Generation Lighting 61660 Installation guide

Brand
Generation Lighting
Model
61660
Type
Installation guide

This manual is also suitable for

Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
FIGURE 1
*NOT INCLUDED
BEFORE YOU BEGIN
Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
HC-1433
1
12008
• Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
• Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
• If you are unclear as to how to proceed, contact a qualified
electrician.
• You don’t need special tools to install this fixture.
• Be sure to follow the steps in the order given.
• Read instructions carefully.
• Save these instructions.
IMPORTANT SAFETY INSTRUCTIONS
Feed the fixture wire through the fixture loop (F) and thread fixture
loop (F) to top of fixture.
STEP 1:
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
CLEANING
ORDERING PARTS
Slide screw collar ring (K) and canopy (G) (in that or
der) to top of
socket assembly (U). Be sur
e not to damage the fixtur
e wir
e. Thread
rod assembly (E) to nipple of the coupling (J).
Feed the fixture wire from the socket assembly (U), thr
ough: the r
od
assembly (E) and thread rod assembly (E) into socket assembly (U).
Assemble r
od assembly (E) by thr
eading desired amount of r
ods
together
.
Secure mounting bar (A) to outlet box using outlet box scr
ews (not
supplied). Thr
ead nut (C) onto nipple (I) so five threads are exposed.
Thread nipple (I) to mounting bar (A) and secure by threading nut (C)
to mounting bar (A). Thread screw collar (B) to nipple (I).
INSTALLATION – ROD ASSEMBLY
STEP 1:
STEP 2:
STEP 3:
STEP 4:
*OUTLET BOX
*WIRE
CONNECTORS
CANOPY (G)
NIPPLE (I)
SHADE (R)
COUPLING (J)
ROD ASSEMBLY (E)
RET
AINING RING (T)
FOR STEM MOUNT
MOUNTING
BAR (A)
SCREW COLLAR
RING (K)
SCREW COLLAR (B)
NOTE: THIS FIXTURE
CAN BE HUNG USING
1, 2, OR 3 RODS.
SELECT THE NUMBER
OF RODS DESIRED.
GREEN GROUNDING
SCREW (D)
SOCKET
ASSEMBLY (U)
NUT (C)
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
FIXTURE
LOOP
(F)
Open other length of chain and attach to the screw collar (B). Close
all lengths of chain to secure.
After wires ar
e connected, tuck them carefully inside outlet box and
then raise the canopy (G) against the ceiling. Secur
e by threading
screw collar ring (K) onto screw collar (B).
Make sure no bare wires can be seen outside wire connectors.
Install lamp.
Place shade (R) securely in socket assembly (U). Secur
e by
threading retaining ring (T) onto socket.
FINAL ASSEMBLY
STEP 7:
STEP 8:
STEP 9:
STEP 6:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is to
be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (D) on the
mounting bar (A). If uninsulated wire is on the mounting bar (A),
connect the ground wire from the fixture (if supplied) and the outlet
box to it using a small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
FIGURE 2
*NOT INCLUDED
*OUTLET BOX
*WIRE
CONNECTORS
CANOPY (G)
NIPPLE (I)
SHADE (R)
COUPLING (J)
ROD ASSEMBLY (E)
RET
AINING RING (T)
FOR CHAIN MOUNT
MOUNTING
BAR (A)
SCREW COLLAR
RING (K)
SCREW COLLAR (B)
NOTE: THIS FIXTURE
CAN BE HUNG USING
1, 2, OR 3 RODS.
SELECT THE NUMBER
OF RODS DESIRED.
GREEN GROUNDING
SCREW (D)
SOCKET
ASSEMBLY (U)
NUT (C)
Slide screw collar ring (K) and canopy (G) over chain to fixture loop
(F).
U
sing 2 pairs of pliers, open one link of chain (M) and attach to
fixture loop at top of fixture. Run wire through every other loop of
chain.
S
ecure mounting bar (A) to outlet box using outlet box screws (not
supplied). Thread nut (C) onto nipple (I) so five threads are exposed.
Thread nipple (I) to mounting bar (A) and secure by threading nut (C)
to mounting bar (A). Thread screw collar (B) to nipple (I).
I
NSTALLATION – CHAIN HC-1433
STEP 1:
S
TEP 2:
STEP 3:
STEP 4:
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
Open other length of chain and attach to the screw collar (B). Close
all lengths of chain to secure.
A. Use a listed wire connector to connect the fixture hot wire (black
wire, or round and smooth tracer) to the supply hot wire.
B. Use a listed wire connector to connect the fixture common wire
(white wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do the wiring connection.
STEP 5:
WIRING
CHAIN (M)
  • Page 1 1
  • Page 2 2

Generation Lighting 61660 Installation guide

Brand
Generation Lighting
Model
61660
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents