Kettler 2533 User manual

Brand: Kettler

Model: 2533

Type: User manual

Place arm rest on top of chair legs, align

front predrilled holes, insert bolt.

2533 ADIRONDACK BAR STOOL

Contents:

(1) Seat, (1) Back

(2) Arm Rests

(2) Front Chair legs

(2) Back Chair legs

(1) Footrest

(2) Side Braces

Tools Required:

7/16” Wrench

(1) Short Cross Brace

(4) Cross Braces

(22) 1/4 - 20 x 2” Bolts

(6) 1/4 - 20 x 2 1/2” Bolts

(12) Washers

(12) Locknuts

a. Align predrilled then

insert bolts to attach

front legs.

b. Align predrilled

holes then insert bolts

to attach back legs.

Locknut Washer 1/4-20 x 2” Bolt

#3 Phillips Head Screwdriver

Properly Seated

Washer and Nut.

Assembly Instructions

a. With the wing on the post facing front,

align the predrilled holes on front leg to the seat

and insert the 1/4 - 20 x 2” Bolts through the leg

in thru the seat. Clean any plastic residue from the

bolt then slide a washer on. Screw on the locknut

and then tighten it with the wrench and phillips

screwdriver. Repeat on the other front leg.

b. Align the predrilled holes on the back leg to

the seat and insert the 1/4 - 20 x 2” Bolts through

the leg in thru the seat. Clean any plastic residue

from the bolt then slide a washer on. Screw on the

locknut and then tighten it with the wrench and

phillips screwdriver. Repeat on the other back leg.

Place arm rest on top of chair legs align the

front predrilled holes and insert the 1/4 - 20 x 2”

Bolts through the leg and in thru the arm. Clean

off any plastic residue then slide a washer on the

end of bolt. Screw on the locknut and then tighten

it with the wrench and phillips screwdriver.

a. Attach the back of the chair to the seat

by aligning holes and inserting a 1/4 - 20 x 2”

Bolt then tighten with a phillips screwdriver.

b. Attach the back of the chair to the arm by

aligning holes and inserting a 1/4 - 20 x 2 1/2”

Bolt thru the arm, leg and into the chair back, then

tighten with a phillips screwdriver.

Repeat on both sides.

Attach the cross braces of the chair to the

legs by aligning holes and inserting a 1/4 - 20 x

2” Bolt through the leg into the cross brace and

tighten with a phillips screwdriver.

Repeat on other leg.

Do Front and Back cross braces.

Slide washer then

locknut onto end of

bolt then tighten.

Attach the braces to

the legs by aligning

holes and inserting

a 2” bolt.

Attach the back of the

chair by aligning holes

on the arm and the seat

to insert bolt.

3b.

3a.

KETTLER® International Inc. • 1355 London Bridge Road • Virginia Beach, VA 23453

www.kettlerusa.com • [email protected]

Care & Maintenance

Ocean Comfort products are constructed from HDPE (High Density Polyethelene), primarily a

recycled material. UV inhibitors are also added to resist fading. Simply maintain your furniture by

cleaning with soap and warm water to ensure its long lasting beauty. A soft bristle brush can be used

on any tough to clean stains. Stainless steel hardware is used in the assembly of these products and

should be rinsed regularly with fresh water if being used in a coastal environment.

KETTLER Limited Warranty

Ocean Comfort products are guaranteed for a period of 20 years (for residential use) and 5 years (for

commercial use), starting from original purchase date. This warranty covers defects in materials and/or

workmanship and does not apply to the hardware.

Warranty not applicable to any products deemed as misused, abused or damaged due to an uncontrollable act

of nature.

*For Parts and Service, please contact us directly at 866-804-0440 or email [email protected]

Made in the U.S.A.

Assembly Instructions continued

a. Bolt the left and right side braces onto the front legs

by aligning the predrilled holes and inserting a 1/4 - 20

x 2 1/2” Bolt. Clean any plastic residue from the bolt

then slide a washer on. Screw on the locknut and then

tighten it with the wrench and phillips screwdriver.

b. Then align the side braces to the holes on the

back legs, place the short brace across between them

aligning with the predrilled holes. Insert the 1/4 - 20

x 2 1/2” thru the leg, in thru the side brace and into

the short brace. Tighten with the phillips screwdriver.

Repeat on the other front leg.

3b. Aligning holes

on the side brace with

the back leg, place

the short brace in

then insert bolt.

3a. Aligning holes on the

front leg and the side brace

then insert the bolt, slide on

a washer, screw on a locknut

and tighten.

3a.

3b.

Short brace goes in between the side

braces on the back of the stool.

Place the footrest on the side braces align the front

predrilled holes and insert the 1/4 - 20 x 2” Bolts through the

footrest and into the end hole of the brace then tighten it with the

phillips screwdriver.

Place the footrest on the side

braces align the front predrilled

holes and insert the bolts.

Kettler 2533 User manual

Kettler 2533 User manual

Related papers

Other documents