Fortinet 2 SXRC User manual

2

SXRC Remote Control

Introduction

Attention:

Please record your purchase information in the area

provided below. We recommend attaching the original

sales receipt or a copy of it to this manual for future

reference.

If you require service on this remote control during the

warranty period, you will need to provide this

information and a copy of the receipt to Kicker

to validate your warranty.

ALWAYS KEEP YOUR RECEIPT!

Congratulations!

You have just purchase the latest in microprocessor

powered amplifier control technology to carry the famous

KICKER name. Your KICKER SXRC is designed and

built to give you years of unmatched control, flexibility

and trouble-free performance in the judging lanes

and on the street.

Please read this installation manual, it contains valuable

information to help you get the most out of your new

SXRC Remote Control.

This is your “Fuel for Livin’ Loud ™“!

SX Series

SXRC Remote Control

Owner’s Manual

SX Series Amplifier Remote Control:

SXRC

Dealer Where Purchased:

Purchase Date:

Model Number:

SXRC

3

SXRC Remote Control

Features

A Brief Plug For The SXRC SX Amplifier Remote

Control And Our Support Materials At

www.KICKER.com

The SXRC is a component we envisioned from the start to

compliment your KICKER SX Series amplifier. That is why all SX

Series amplifiers have been built from day one with the ability to

be controlled remotely...and now you have the tool to do so, the

SXRC. The SXRC incorporates the latest in microprocessor

technology which allows you to not only update the software in

your SX Series amplifier (so you are always on the cutting edge)

but also group, diagnose and control them in a way never before

possible in the car audio world. This technological marvel is

loaded with diagnostic and control features that literally put the

SX Series amplifier controls at your fingertips from the driver’s

seat...plus a whole lot more! PLEASE read this manual so you

have a thorough understanding of the capabilities, installation and

operation of your SXRC. Also, sometimes things change, we find

things we overlooked or a customer points out a mistake we

made when writing this manual. When in doubt, always check out

the SUPPORT section at www.KICKER.com for the latest

information. If we change anything in this manual, or add to it,

you will always find the latest version available for download

there. Last but not least...grab a cold beverage, kick back and

read about this latest creation from the Livin’ Loud Labs. Enjoy!

Full Control Of SX Amplifiers The SXRC gives you

complete access to all settings and diagnostic tools for up to 16

KICKER SX Series amplifiers.

Very Important Note!!!

Ok...we know you are chomping at the bit to get this new toy

plugged in and working but there are some initial steps you will

have to take before you can use your SXRC with your SX Series

amplifiers.

After you follow the instructions for mounting and wiring your

SXRC into your system you will have to perform these steps

before you can use your SXRC.

1.) SET EACH OF YOUR SX AMPLIFIERS TO A UNIQUE

COMMUNICATION ADDRESS.

In order for the SXRC to properly communicate with all

your SX Series amplifiers, each amplifier must have its

own unique Communication Address.

2.) PERFORM A SOFTWARE UPGRADE TO ALL OF YOUR

SX SERIES AMPLIFIERS!

The SXRC has new software (Version 3.00) loaded into it for

all SX Series amplifiers. By using a one-at-a-time process,

each of your amplifiers will need to be updated to Version

3.00 so that all SXRC functions work properly.

So get your initial mounting and wiring done but keep in mind

that BOTH of the steps outlined above MUST be performed

before your SXRC will work properly with your SX Series

amplifiers.

PLEASE read the entire manual so you are aware of ALL the

steps required for this procedure.

4

SXRC Remote Control

Features

Amplifier Adjustment Allows you to individually select and

adjust any setting on any amplifier controlled by the SXRC.

Amplifier Grouping & Group Adjustment Allows you to

build groups of amplifiers which can then share similar settings

and be adjusted all at once. Great for multiple sub amps, front

stage, rear stage, etc!

SickBay ™ Allows you to view operation history and use

diagnostic tools on any amplifier connected to the SXRC.

SXRC Setup Allows you to setup and adjust many options for

the SXRC like ISIS display brightness, lock codes, amp names,

memory names, etc. See details further in the manual.

Security Mode Allows you to ‘Lock’ and ‘Unlock’ your SXRC

and connected SX amplifiers to prevent un-authorized

adjustments.

Global Memory Presets Allows you to store and recall up to 4

memory settings for all amplifiers connected to the SXRC.

DIN Sized Control Head The controller for the SXRC is very

thin and includes hardware to be mounted in a standard DIN

sized opening.

ISIS Display Indicate Status & Input Settings ISIS is a VFD

(Vacuum Fluorescent Display), 5-way soft-touch keypad and 4

memory presets that allows you to view any current settings and

make changes to your SXRC and the connected amplifiers.

SXRC Name The name of the SXRC is displayed in the default

screen scrolling menu. Name is ‘SXRC’ by default but can be

changed by you to any name using up to 10 characters.

Digital Remote Volume Control (DRVC) Allows instant

control of the output level of selected amplifiers. The current

setting of the digital remote volume control is displayed in the

default screen scrolling menu.

Number Of Units Under SXRC Control The number of

amplifiers currently being controlled by the SXRC is displayed in

the default screen scrolling menu.

Real Time Calendar & Clock The SXRC is capable of

displaying the current date and time and is user adjustable.

Amplifier Temperature Display Selected amplifier’s

current temperature is displayed in the default screen scrolling

menu. All amplifiers can be viewed through SickBay™.

Amplifier Voltage Display Selected amplifier’s current

voltage is displayed in the default screen scrolling menu. All

amplifiers can be viewed through the SickBay™.

5

SXRC Remote Control

Features

Metal DIN Mounting Cage This cage is designed to mount

into a standard DIN sized opening and provide a solid mounting

for your SXRC.

Plastic Cosmetic Trim Ring This ring trims out the DIN

Mounting Cage and provides a professional finished look to your

install.

R-Tool Tool used to assist in removing the SXRC Control Head

from the Plastic Cosmetic Trim Ring.

X 2

Parts List

Here is a breakdown of the components and accessories

included with your SXRC Remote Control kit.

SXRC Control Head This is the DIN sized unit used to control

the SXRC and your SX amplifiers. It includes an attached 1 meter

long 6-pin DIN cable. This cable is also referred to as a PS2

cable and you can use an extension (Male to Female) cable to

lengthen the cable if required (not included).

SXRC Interface Box This small enclosure provides the power

connections for the SXRC as well as being the communication

bridge between the Control Head and your SX Series amplifiers.

M1

M2

M3

M4

HOME

ENT

ESC

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

** kicker

FROM AMP

+ 12V

REM

GND

TO SXRC

6

SXRC Remote Control

Features

ISIS

The ISIS (Indicate Status & Input Settings) system consists of

the VFD (Vacuum Fluorescent Display) and nine soft touch

buttons that make up the Keypad. The ISIS allows you to view

and adjust the settings of your SXRC and all of the SX Series

amplifiers connected to it.

VFD DISPLAY

Here is a brief description of the indicators found on the VFD.

AMP1 - Indicates amplifier 1 is selected for adjustment. Only

available with four channel amplifiers.

AMP2 - Indicates amplifier 2 is selected for adjustment. Only

available with four channel amplifiers.

LOCK - Indicates the SXRC and/or SX Series amplifier controls

are locked out and not usable.

LEFT - Indicates an action or adjustment of the left channel.

SYS - Indicates you are in the System Menu.

M1

M2

M3

M4

HOME

ENT

ESC

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

** kicker

Mounting Hardware Includes four (4) sheet metal screws for

mounting the Interface Box and two (2) M3 flathead screws to

mount the Cosmetic Trim Ring to the DIN Mounting Cage.

Rubber Mounting Washers Includes four

(4) rubber mounting washers to protect the

mounting flange on the Interface Box.

One 5-Meter Network Cable This cable is used to create your

SXRC Communications Network and connects your Interface Box

to your first SX amplifier. This cable is known as a Straight-

Through Ethernet Cable.

Two 1-Meter Network Cables These cables are used to

connect additional SX Series amplifiers to the SXRC

Communications Network. These cables are known as a Straight-

Through Ethernet Cable.

3 Amp Mini Glass Fuse Extra replacement fuse for use in

SXRC Interface Box. See the Service section of this manual for

replacement instructions

X 4

X 2

X 4

250V

3A

7

SXRC Remote Control

Features

KEYPAD

Here is a brief description of the soft touch buttons.

M1 - Used to select memory preset 1 or to store current

settings into memory preset 1.

M2 - Used to select memory preset 2 or to store current

settings into memory preset 2.

M3 - Used to select memory preset 3 or to store current

settings into memory preset 3.

M4 - Used to select memory preset 4 or to store current

settings into memory preset 4.

ESC - Used to exit the current menu.

ENT - Used to enter the selected menu.

HOME - Used to return to the Main Menu and other

functions explained later in this manual.

UP - Used to advance up through menu selections

and/or adjust SXRC and amplifier controls.

DOWN - Used to advance down through menu selec-

tions and/or adjust SXRC and amplifier controls.

These controls and their usage will be explained later with

more detail in each menu usage section.

M1

M2

M3

M4

ESC

ENT

HOME

RIGHT - Indicates an action or adjustment of the right

channel.

MUTE - Indicates you are in the mute menu or the mute

function is active.

GAIN - Indicates you are in the gain menu.

EQ - Indicates you are in the equalizer menu.

LPF - Indicates you are in the low pass filter menu.

HPF - Indicates you are in the high pass filter menu.

PHASE - Indicates you are in the phase menu.

KOMP - Indicates you are in the Kompressor™ menu.

MEM-1 - Memory preset 1 activated or stored.

MEM-2 - Memory preset 2 activated or stored.

MEM-3 - Memory preset 3 activated or stored.

MEM-4 - Memory preset 4 activated or stored.

8

SXRC Remote Control

Installation

Mounting

DIN Mounting

Using the supplied hardware you can mount the SXRC into a

standard DIN sized opening.

Be sure you will have a minimum of 2”

(51 mm) clearance depth behind your mounting

surface panel to mount the SXRC.

If not using an existing DIN opening, you will first need to cut

an opening that is 7-3/16” (182 mm) by 2-1/8” (53 mm) into your

mounting surface panel.

It is VERY important that you DO NOT make the hole any

larger than the specified dimensions. If you make the opening too

large then the mounting cage will not work properly.

7-3/16"

2-1/8"

182 mm

53 mm

2"

51 mm

Mounting

Surface

Other

Surfaces

7-3/16"

2-1/8"

182 mm

53 mm

Using the existing DIN opening or

the one you just created, slide the

Metal DIN Mounting Cage into the

opening. Secure the Cage by bending

the Mounting Tabs on the sides, top

and bottom of the Cage using a small

flat-blade screwdriver. Use only the

tabs that when bent will secure the

Cage to the Mounting Surface.

Next, place the Plastic Cosmetic Trim Ring into the Metal DIN

Mounting cage. There are two plastic retainers in the Trim Ring

(one on top and one on bottom) that will snap into place.

Mounting

Surface

SMAC-ON TOOLZ

Mounting

Tabs

Mounting

Surface

Mounting

Tabs

SMAC-ON TOOLZ

Side View

Top and Bottom View

Plastic Cosmetic Trim Ring

Mounting

Surface

Metal DIN Mounting Cage

9

SXRC Remote Control

Installation

Once in place use the 2 supplied M3 flathead screws to secure

the Trim Ring to the Metal Cage.

The SXRC Control Head is held in place by two clips (one on

each side) of the Plastic Trim Ring.

Trim Ring & Metal Cage Assembly

Front View

Screws Here

Mounting

Surface

Trim Ring & Metal Cage Assembly

Side View

Mounting

Surface

SXRC Control Head

Mounting Clips

Route the SXRC Control Head cable through one of the

openings in the Trim Ring/Metal Cage assembly to your SXRC

Interface Box location.

Press the SXRC control head in to the assembly until it locks

into place.

Your SXRC Control Head is now mounted and you can move

on to the wiring section of this manual

M1

M2

M3

M4

HOME

ENT

ESC

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

** kicker

M1

M2

M3

M4

HOME

ENT

ESC

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

** kicker

10

SXRC Remote Control

Installation

Surface Mounting With Screws

The SXRC Control Head can also be surface mounted if you

do not have a spare DIN opening in your dash or do not want to

cut one into an existing panel.

The back of the SXRC Control Head has two metal inserts

designed to work with M3 screws.

Find a suitable location and drill two 1/8 inch (3 mm) holes to

secure the SXRC Control Head.The holes should be 5-17/32”

(140 mm) apart from center to center.

NOTE: You will need to have access to the area behind this

location to install the mounting screws.

Inserts for M3 Screws

Center to Center

5-17/32" (140mm)

Mounting Surface

Center to Center

5-17/32" (140mm)

Once your holes are drilled you can use the two supplied M3

screws to secure the SXRC Control Head to your mounting

surface. If the supplied screws are not long enough to reach the

SXRC Control Head you can supply your own M3 screws of the

required length to secure the SXRC.

NOTE!!! Whether using the supplied M3 screws from the SXRC

kit or your own, the screws can not enter into the SXRC more

than 5/16” (4 mm). If you attempt to insert the screw any deeper

than this into the SXRC Control Head you will run the risk of

damaging the unit.

Route the SXRC Control Head cable to your SXRC Interface

Box location.Your SXRC Control Head is now mounted and you

can move on to the wiring section of this manual.

Mounting Surface

NO MORE THAN 5/16" (4 mm)

Mounting Surface

11

SXRC Remote Control

Installation

Surface Mounting With Velcro

If you do not want to cut any openings or drill any holes you

can use a material such as Velcro™ to secure your SXRC

Control Head to your dashboard or other mounting surface.

Velcro™ is not supplied with your SXRC but can be obtained

from any local fabric or retail store.

Velcro™ is a two

piece product, one half

is soft and fuzzy(loop)

while the other is stiff

and prickly (hook).

Place a 5” (127 mm)

strip of the loop half on

the SXRC.

Place the 5” (127 mm)

strip of the hook half on

the mounting surface.

The SXRC Control Head will now be able to stick to the dash

or other mounting surface. Route the SXRC Control Head cable

to your SXRC Interface Box location.Your SXRC Control Head is

now mounted and you can move on to the wiring section of this

manual.

Loop Side Of Velcro™ Strip

Mounting Surface

Hook Side Of Velcro™ Strip

Mounting Surface

Stiff Side Of Velcro™ Strip

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

** kicker

HOME

ENT

ESC

M1

M2

M3

M4

Got No Time For Mounting

If this is the case there are many options...ranging from ‘Ok’ to

‘What are you thinking?’...and we do not recommend any of

them. But we know some of you may use these...or a variation of

them...so we included these for your entertainment. Got your own

idea? E-mail them to questions@kicker.com, Attn: Hank.

In the center console. This one makes some sense as it

keeps the SXRC in an ‘easy to access’ location while protecting it

from your gym bag that gets tossed in the ride everyday for ball

practice.

In the glove box. Another excellent choice for protection. Just

be sure you run the SXRC Control Head cable through the back

of the glove box...not out the front with the door pinching the wire.

Lay it in the seat. This allows quick and easy access to your

SXRC...just be sure that your girl or best friend Larry does not sit

on it when sharing your ride. Being ‘sat on and squashed’ is not

covered under warranty.

Lay it in the catch-all pocket in your center console. This

also allows quick and easy access to your SXRC...plus it adds

another item to rattle along with all those nickels, dimes and

quarters sitting there. Could be very harmonious.

Stand vertically in your cup holder. This is an excellent

location that puts your SXRC within reach. Just be sure to tell

your guests riding in the car that one cup holder is for you and

the other is for your remote...they will just have to hold their

128 oz. Super Ultra Chug drink.

Under your seat. This location is not ideal but is usable. When

you need to adjust your SXRC simply ‘tap’ the brakes which will

slide the unit forward onto your floor mat for easy access.

12

SXRC Remote Control

Installation

Using the R-Tool

The included R-Tools are used to remove the SXRC Control

Head from the Trim Ring/Metal Cage assembly. The R-Tools

simply slide into the notched area on both sides of the Plastic

Cosmetic Trim Ring and will release the clips holding the SXRC

Control Head.

M1

M2

M3

M4

HOME

ENT

ESC

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

** kicker

R-Tool R-Tool

Wiring

Now that you have mounted your SXRC Control Head it is time

to do some wiring. The first step is to plug your SXRC Control

Head into the SXRC Interface Box.

Next, run a fused (5 amp) constant 12 volt, ground and remote

turn on to the SXRC Interface Box. Connect the wiring to the

removable power plug by loosening the set screws, inserting the

stripped wire and then tightening the set screw.

M1

M2

M3 M4

HOME

ENT

ESC

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

** kicker

FROM AMP

+ 12V

REM

GND

TO SXRC

Interface Box

Control Head

Power On

LED

PS2 - SXRC

Connector

HyperFlex

Strip Back Wire

1/4" (6 mm)

Ground

Remote

+ 12 Vol

t

Tighten Set ScrewLoosen Set Screw

5

Fuse

13

SXRC Remote Control

Installation

Now insert the removable power plug into the SXRC Interface

Box.

You should have something resembling this picture at this

point. The Control Head plugged in and the power plug wired

correctly and plugged in.

FROM AMP

+ 12V

REM

GND

TO SXRC

Interface Box

RJ45 Communication

Network Jack

Power, Ground

Remote Jack

+12 Vol

t

Ground

Remote

HyperFlex

5

Fuse

Control Head

M1

M2

M3

M4

HOME

ENT

ESC

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

** kicker

+12 Volt

Ground

Remote

HyperFlex

FROM AMP

+ 12V

REM

GND

TO SXRC

Interface Box

5

Fuse

NOTE!!!

There are 8 pins in each RJ45 jack used on the SXRC

Interface Box and on SX Series amplifiers. We only use 3 of

these pins for the Digital Communications Network: Pins #2, #7

and #8.

If pins #2, #7 or #8 are bent or damaged, you will not be able

to establish reliable communications on the SXRC Digital

Communications Network.

A common issue is if your SX Series amplifier has been used

with the Remote Bass Level Controller prior to being used with

the SXRC. Some cables that came with the SX Series amplifiers

for use with the Remote Bass level Controller will bend pins #1

and #8 down too far causing poor contact with the SXRC

Communications Network Cable. To fix this simply take a small

screwdriver or paper-clip and pull these pins back up into place.

Check all the RJ45 jacks on your amplifiers to insure the pins

are up and in place before plugging in any of your SXRC

Communications Network Cables.

12345678

SX Amplifiers

SXRC

14

SXRC Remote Control

Installation

Now we can run the Network Cables from the SXRC Interface

Box to your SX Series amplifiers to create the SXRC

Communications Network.

Run the supplied

5-meter Network Cable

from the Interface Box to

the REMOTE IN jack of

your first SX Series

amplifier.

Run the first supplied

1-meter Network Cable

from the first SX Series

amplifier’s REMOTE OUT

jack to the REMOTE IN

jack of the second

amplifier.

Run the second supplied

1-meter Network Cable

from the second SX Series

amplifier’s REMOTE OUT

jack to the REMOTE IN

jack of the third amplifier.

You can continue adding

amplifiers (16 total) by

following this setup and

supplying your own

Network Cables.

FROM AMP

+

12

V

R

E

M

G

N

D

TO SXRC

Interface Box

Communication

Network Jack (RJ45)

Power, Ground

Remote Jack

+12 Vol

t

Ground

Remote

HyperFlex

AMP STRAPPING

IN OUT

AMP STRAPPING

IN OUT

AMP STRAPPING

IN OUT

5-Meter Network Cable

1-Meter Network Cable

To Next Amplifier

Additional Network Cable

(Supplied By You)

5

Fuse

SXRC Network Cables

The SXRC is supplied with 3 Network Cables, one 5-meter and

two 1-meter. This is enough to connect 3 SX Series amplifiers to

the SXRC Interface Box. You can connect up to 16 SX Series

amplifiers to the SXRC by supplying additional cables.

If you need additional cables or need to use custom lengths,

you can purchase pre-made cables at any computer or

electronics store. You want to purchase a Straight-Through,

Ethernet Network Cable.

If you want to make your own custom length cables you will

need:

•Bulk Cat3, Cat5, Cat5e or Cat6 network cable.

•Crimp on RJ45 plugs.

•Cable cutters.

•Electrician's scissors.

•RJ45 crimp tool.

•A UTP/Network Cable stripping tool.

Step 1.) Cut a piece of net-

work cable the required length

from the bulk cable roll using

your Cable Cutters.



15

SXRC Remote Control

Installation

Step 2.) Using the UTP/Network Cable stripping tool, remove

1 inch (25 mm) of the outer insulating jacket from each end of the

cable exposing the 8 wires (4 twisted pairs).

Step 3.) Untwist the 4 wire pairs on each end back to the

outer insulating jacket and lay them in this order.

•Orange-White

•Orange

•Green-White

•Blue

•Blue-White

•Green

•Brown-White

•Brown

Step 4.) Hold the now

grouped and sorted wires

together tightly and using the

Electrician's Scissors cut

them all 1/2 inch (13 mm) in

length at a 90 degree angle.

NOTE: The wires must be cut at a 90 degree angle to insure

proper fit in the RJ45 plug.

Step 5.) Slide an RJ45 plug (clip side down) onto the cable

and seat it fully onto the cable. The 8 wires should butt up against

the end of the plug tightly. Crimp the plug onto the wire securely

using the RJ45 Crimp Tool. Repeat the process for the other end

of the cable.

Step 6.) Lay the cable ends side by side (clip down) and verify

the wire colors are in the correct order. The ends should be

identical. If they are not, cut off the incorrect end and return to

step 2 to put on a new RJ45 plug.

1 inch

(25 mm)

Network

Cable

Network

Cable

•Blue-White

•Blue

•Green-White

•Green

Pair 1

Pair 2

Pair 3 Pair 4

•Orange-White

•Orange

•Brown-White

•Brown

1/2 inch

(13 mm)



90°

Network

Cable

Network

Cable

Yes !

No !

Network

Cable

Yes !

No !

Network

Cable

Network

Cable

Network

Cable

1-Orange-White

2-Orange

3-Green-White

4-Blue

5-Blue-White

6-Green

7-Brown-White

8-Brown

Network

Cable

1

2

3

4

5

6

7

8

1

2

3

4

5

6

7

8

16

SXRC Remote Control

Installation

Software Updates

Now that you have the SXRC mounted and wired properly it is

time to update the software in all of your SX Series amplifiers.

This process has to be completed for EACH amplifier and does

require you to disconnect

and reconnect cables

between each step.

Please read the

instructions and follow

them exactly as

described.

You only have to do this

setup and programming

process one time for each

amplifier.

Step 1.) Un-plug the

Communications Network

Cables from the REMOTE

OUT jacks on ALL the SX

Series amplifiers. Leave

the Communications

Network Cables

connected to the

REMOTE IN jacks. The

SXRC Interface Box

should only be connected

to the first SX Series

amplifier as the diagram

to the right is showing.

NOTE!!!

Each SX Series amplifier must be assigned its own unique

address from the amplifier’s keypad before it can be updated and

controlled by the SXRC. This has to be done at each amplifier

’s

keypad and can not be done from the SXRC. Think of the

amplifiers like houses...no two houses can share the same street

address...the mailman would throw a complete fit! Well, the

SXRC feels the same way about two amps sharing the same

Remote Communication Address.

Each series of SX amplifiers (.2-Stereo, .1-Mono Block, .4-Four

Channel) has a unique address range that is not shared between

the others. So it is impossible to accidentally share addresses

from one series with another. All you need to do is assign a

unique (different) address to each amplifier in you system. The

possible choices for each series are:

All SX Series amplifiers are shipped from the factory with their

Remote Address set to the lowest setting.

For example, lets say you have 4 SX.2, 4 SX.4 and 4 SX.1

amplifiers in your system for a grand total of 16 amplifiers. Set the

Remote Addresses as such:

FROM AMP

+

12

V

R

E

M

G

N

D

TO SXRC

Interface Box

Communication

Network Jack (RJ45)

Power, Ground

Remote Jack

+12 Vol

t

Ground

Remote

HyperFlex

AMP STRAPPING

IN OUT

AMP STRAPPING

IN OUT

AMP STRAPPING

IN OUT

5-Meter Network Cable

1-Meter Network Cable

To Next Amplifier

Additional Network Cable

(Supplied By You)

5

Fuse

SX.2 # 1 - 10

SX.2 # 2 - 11

SX.2 # 3 - 12

SX.2 # 4 - 13

SX.2 Series - Addresses 10-59

SX.1 Series - Addresses 60-109

SX.4 Series - Addresses 110-119

SX.1 # 1 - 60

SX.1 # 2 - 61

SX.1 # 3 - 62

SX.1 # 4 - 63

SX.4 # 1 - 110

SX.4 # 2 - 111

SX.4 # 3 - 112

SX.4 # 4 - 113

SX.2 Series - Address 10

SX.1 Series - Address 60

SX.4 Series - Address 110

1717

SXRC Remote Control

Installation

The important thing is that no matter what combination of

amplifiers you are running, each amplifier must have its own

unique Remote Address.

It is also a good idea to write down which amplifier has been

assigned which address. This will help you later in identifying the

amplifier and assigning it a name based on its function. For

example:

BASS AMP 1, BASS AMP 2, FRONTSTAGE, MIDBASS,

etc. A fill-in-the-blank form is provided in the back of this manual

to assist you.

Step 2.) Power up your system so you can access the settings

and controls of your SX Series amplifiers. When the amplifiers

power up you will see

* KICKER *. You are now in the amplifiers

Default Screen.

Step 3.) Press the ENT key to enter the Main

Menu of the amplifier.

Step 4.) Press the UP or DOWN key until the

display reads

SYSTEM. Press the ENT key to enter

the System Menu.

Step 5.) Press the UP or DOWN key until the

display reads

Remote adr. Press the ENT key to

enter the Remote Address Selection Menu.

Step 6.) Press the UP or DOWN key to select

the Remote Address you want to assign to this

amplifier. Press the

ESC key three times to save

your setting and return to the Default Screen.

Step 7.) Repeat steps 3 through 6 for each amplifier.

Step 8.) Power cycle your system by turning it off, waiting 3

seconds, then turning it back on.

NOTE:

At this point each SX Series amplifier has been assigned a

unique Remote Address. Be sure you have properly done this to

each amplifier before proceeding! If multiple amplifiers share the

same address, they all will be detected and you will corrupt the

software that is loaded into each of the amplifiers. If this

happens the SXRC display will flash

FAILED and then show

Manual SW Update Required . You will then need to perform a

Manual Software Update (

SW UPDATES Menu) as described on

page 73 in this manual for each amplifier.

If you need assistance please visit your local KICKER dealer or

contact KICKER Technical Services.

Step 9.) The SXRC will display

STARTING * while the amp(s) and remote

are booting. When completed booting it will

switch to

* KICKER * . You are now in the

Default Menu.

Step 10.) Press the ENT key one time to enter

the SXRC Main Menu. The first Main Menu item will

be displayed which is

AMP ADJ.

Step 11.) Press the UP or DOWN key until

the display reads

SXRC SETUP . Press the ENT

key to enter the SXRC SETUP Menu.

Step 12.) Press the UP or DOWN key until

the display reads

AUTOSearch . Press the ENT

key to activate the AUTOSEARCH function.

HOME

ENT

ESC

HOME

ENT

ESC

HOME

ENT

ESC

HOME

ENT

ESC

ss**taarrttiinngg

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

**** kkiicckkeerr

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

HOME

ENT

ESC

HOME

ENT

ESC

HOME

ENT

ESC

EXTREMELY IMPORTANT NOTE:

DO NOT power down your system or amplifiers during this

process (Step 13, A-P). Doing so will

corrupt the software and force you to

perform a Manual Software Update!

18

SXRC Remote Control

Installation

Step 13.) The SXRC is now:

A.) Searching for the first amplifier

connected to the Communications

Network.

B.) Detecting the amplifier’s

software boot loader.

C.) Erasing the old software.

D.) Loading the new software into

the amplifier.

E.) Checking the software in the

amplifier to insure it has been

loaded correctly.

F.) Confirming the software update

is successful.

G.) Loading the amplifier into the

SXRC.

H.) Displaying how many amplifiers

have been detected (1 at this

point), successfully updated and

brought into the SXRC

Communications Network.

ss eaarrcchh **

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

ddrretteecctt lldd

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

ee raassiinngg **

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

pp00rooggrraamm==00

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

vv00erriiffyy ==00

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

vv erriiffyy ookk

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

**looaaddiinngg

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

1 uunniittss

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

A

B

C

D

E

F

G

H

The SXRC will now ask you if you

want to save the current settings of your

amplifier into a memory preset. Use the

UP or DOWN keys to select:

I.) SAVE - YES

J.) SAVE - NO

and press the ENT key to select.

If you select

SAVE - NO then the

amplifier’s current settings are not stored

into the SXRC.

If you select

SAVE - YES then you

choose which Global Memory Location to

store the amplifier’s settings in by using

the

UP or DOWN key to scroll through

the options (

K, L, M, N). When the

memory you want to use is selected

press the

ENT key to store. The SXRC

will respond by blinking

STORED (O) to

confirm the memory storing has

completed successfully.

The display will then read

AUTOSEARCH

(P) which indicates the software update

process has completed and the SXRC is

ready to find and update another SX

Series amplifier.

All of the above steps happen

automatically once you initiate the

AUTOSEARCH function.

ssssavvee -- yyee

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

ss avvee -- nnoo

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

meemmoorryy--11

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

meemmoorryy--22

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

meemmoorryy--33

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

meemmoorryy--44

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

ssttoorreedd

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

aahhuttoosseeaarrcc

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

I

J

K

L

M

N

O

P

19

SXRC Remote Control

Installation

NOTE:

If steps 8-13 worked correctly, you have taken the first step to

remote control bliss, skip to step 14. If not, then read on.

If the display came back blinking

0 Units after doing the

AUTOSEARCH then there is a problem with the Communications

Network.

• Go back and double check your Communications Network

cable and make sure it is inserted properly and ‘snapped’ into

place.

• If you have purchased different cables, double check that they

are Straight-Through Ethernet Network cables.

• If you have made your own cables double check them for

secure and proper termination.

• Did you check the pins (#1 and #8) in the SX Series

amplifiers to make sure they are not bent or damaged?

You have to get the Communications Network working with the

first amplifier and update its software before we can proceed with

the rest of the amplifiers so double check everything. Try a

different cable if necessary. Repeat steps 8-13 after double

checking your cable and jacks. Once the first amp is successfully

updated and in the SXRC Communications Network you can

move on to step 14.

If you can not get the amplifier to accept a software update

then visit your local KICKER dealer or call KICKER Technical

Services for more troubleshooting advice.

Step 14.) If you are

only controlling one SX

Series amplifier with the

SXRC (yeah...right...we

bet you have at least two!)

you can skip to the next

section in the manual

titled Operation (look for

the gray box tabs on the

side of the pages...in case

you missed that up to

now). If you have more

than one SX Series

amplifier to control then

continue with Step 15.

Step 15.) Plug the

Communications Network

Cable from the REMOTE

IN jack on the second

amplifier into the

REMOTE OUT jack of the

first amplifier in the chain.

Even if you have more

than two amps, at this

point only the first and

second one should be

connected as the diagram

on the right shows.

FROM AMP

+

12

V

R

E

M

G

N

D

TO SXRC

Interface Box

Communication

Network Jack (RJ45)

Power, Ground

Remote Jack

+12 Vol

t

Ground

Remote

HyperFlex

AMP STRAPPING

IN OUT

AMP STRAPPING

IN OUT

AMP STRAPPING

IN OUT

5-Meter Network Cable

1-Meter Network Cable

To Next Amplifier

Additional Network Cable

(Supplied By You)

5

Fuse

20

SXRC Remote Control

Installation

NOTE: If you take longer than three minutes to plug the

Network Cable in from the second amplifier (Step 15) the SXRC

will time out and return to the scrolling Default Menu. If this

happens you will then need to skip Step 16 and return to the

Autosearch Menu by following Steps 17-19.

Step 16.) If the ISIS Display is showing

AUTOSEARCH press the ENT key to detect, update

and load the second amplifier. Skip to Step 20.

Step 17.) Press the ENT key one time to enter

the SXRC Main Menu. The first Main Menu item will

be displayed which is

AMP ADJ.

Step 18.) Press the UP or DOWN key until

the display reads

SXRC SETUP . Press the ENT

key to enter the SXRC SETUP Menu.

Step 19.) Press the UP or DOWN key until

the display reads

AUTOSearch . Press the ENT

key to activate the AUTOSEARCH function.

Step 20.) The SXRC is now searching

for the second amplifier connected to the

Communications Network. It will do the

exact same sequence (A-P) as in step 13.

Once it detects the amplifier it will load the

new software into the amplifier and verify

the software upload has been successful.

The remote will then display how many

amplifiers have been detected (2 at this

point), successfully updated and brought

into the SXRC Communications Network.

HOME

ENT

ESC

HOME

ENT

ESC

HOME

ENT

ESC

ss eaarrcchh **

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

pp00rooggrraamm==00

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

vv00erriiffyy ==00

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

2 uunniittss

SYS

MEM-1

GAIN EQ LPF HPF KOMP

AMP1

LOCK

MEM-2 MEM-3 MEM-4

PHASE

MUTE

AMP2

LEFT RIGHT

Like before, the SXRC will ask if you want to

save the current settings of your second amplifier

into a memory preset. Use the

UP or DOWN

keys to select SAVE - YES or SAVE - NO and

press the

ENT key to select.

If you select

SAVE - NO then the amplifier’s current settings

are not stored into the SXRC.

NOTE:

The memory settings in the SXRC are a global memory

system. What this means is that each memory preset (1-4) stores

the settings of all (up to 16) the amplifiers connected to it. This

allows you to have unique settings for each amplifier stored and

ready for instant recall. If you chose

Memory-1 before, you can

choose it again. All amplifiers will have their individual settings

stored here in memory location 1 for instant recall later.

If you select

SAVE - YES then you choose which Global

Memory Location to store the amplifier’s settings in by using the

UP or DOWN key to scroll through the options

(

Memory-1 through Memory-4). When the memory

you want to use is selected press the

ENT key to

store. The SXRC will respond by blinking

STORED to

confirm the memory storing has completed successfully.

The display will then read

AUTOSEARCH which indicates the

software update process has completed.

HOME

ENT

ESC

HOME

ENT

ESC

HOME

ENT

ESC

Page is loading ...

Fortinet 2 SXRC User manual

This manual is also suitable for

Fortinet 2 SXRC User manual

Other documents