Heath Zenith 598-1109-06 User manual

Heath Zenith
Brand
Heath Zenith
Model
598-1109-06
Type
User manual
This package includes (Style of push button and chime may vary from illustration):
• Wirelesschime
• Wirelesspushbuttonwithbattery
• Hardwarepack
This chime requires 4 “C” alkaline batteries (not included). In typical use,
alkalinebatterieswilllastupto2
1
/
2
years.
Wireless Mechanical
Battery Operated
Chime
©2008HeathCoLLC 598-1109-06
Figure 2
Figure 3
1. Install alkaline type A23 12 volt push button
battery (included). Remove back of case by
pushingintabonbottomwithasmallscrew-
driver. See diagram inside push button for
correct battery orientation. Note: If batteries
are preinstalled, remove orange battery tab.
2. Remove chime cover.Pullrmlyasshown
inFigure2.
3. Install 4 alkaline “C” batteries in chime.
Make sure batteries are oriented properly as
showninFigure3.
4. Test range. Temporarily position chime and
pushbuttonwhereyouwantthemmounted.
Press push button to verify chime and push
buttonworkproperly.Ifchimedoesnotsound,
see Troubleshooting.
Figure 1
1 2 3 4 5 6 7
ON
Type “C” Type “C”
Type “C”Type “C”
WARNING: To prevent possible
SERIOUS INJURY or DEATH:
 
batteries.
     

-2-
598-1109-06
5. Mount push button. Useeitherscrewsordoublesided
tape to mount push button.
• Tomount withscrews,remove
backofcasebypushingintabonbottomwithasmall
screwdriver(seeFigure1).Note: Remove material in
screwholes(ifneeded)beforemountingwithscrews.
Attachbackofcasetodoorjamborwall(seeFigure
4). Snap front of push button on.
• Tape Mounting:Whenattachingpushbuttonusing
double sided tape, make sure the surface of the door
jamborwallisclean.
6. Mount chime. Determine mounting location.
 There are threedifferent waysto mount the chime
depending upon the model of chime purchased. De-
terminewhichmodelyoupurchasedbelow.Mountthe
chime according to the instructions for your chime.
Basic Chime with Separate Chime with Attached
Chime Decorative Cover Decorative Cover
Style of push button and chime may vary from illustration.
Figure 4
-3-
598-1109-06
Basic Chime:
1. Remove batteries from chime.
2. Placechimeagainstwallandverifythechimeislevel.
3. Usechimeholesasatemplate(seeFigure5).Drill7/32"diameterpilothole
for2wallanchors(provided)andinsertanchors.
4. Insert2screws(provided)throughholesinbackofchime.
5. Usingarrowinsidechimeunitasaguide,mountchimewitharrowpointing
up(seeFigure5).Donottightencompletely.
6. Verifychimeislevelandtightenscrewssecurely.
7. Replacebatteries(seeFigure3).Snapcoverontochimebase.
1 2 3 4 5 6 7
ON
Holes
forWall
Mounting
Figure 5
Mount
ChimeUnit
withArrow
Pointing Up
1 2 3 4 5 6 7
ON

1. SlidecoverpinontorearofchimeasshowninFigure6.Pinmustbeassem-
bledtobasepriortomountingbasetowall(pinmaybepre-assembled).
2. Followdirectionsunder“BasicChime”tomountchimebasetowall.
3. Hangcoveroncoverpin.
Figure 6
TopofChime
BackofChime
CoverPin
CoverPin
Installed on
ChimeBack
-4-
598-1109-06
   
Cover:
1. Mount hanger to chime (hanger
maybepre-assembled):
• Place hanger over predrilled
holes (either in top or bottom
panel).
• Connecthangertochimeusing
2#4screws(provided).
2. Determinewherechimeistobe
mounted.
3. Drill 1/4" diameter pilot hole for
wallanchor(provided)andinsert
anchor.
4. Screw#8screw(provided)intoanchor.Leave1/16"gapbetweenscrewhead
andwall.
5. Placehangeroverscrewtomountchime.
Figure 7
Predrilled
Hanger
Holes
Hanger
#4Screws
-5-
598-1109-06
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
PushButtonSet
for One Note Tune
(Dong)
Note: Some models might require
the use of tweezers to remove
and replace the jumpers.
Figure 8 - Inside Push Button
Tune Settings
Yourwirelesschimehasdifferentselectabletunes:Dong (one note) and Ding-
Dong(twonote).ThefactorysettingisfortheDing-Dongtune.Thistunecan
bechangedbyfollowingtheinstructionsbelow.
• Dong (one note tune)
 InsidePushButton:Addjumpertolocation8.
• Ding-Dong(twonotetune)
 InsidePushButton:Removejumperfromlocation8.
Note:Allmodelshavebothfrontandbackdoortunecapabilities.Werecommend
the back door use the Dong tune and the front door use the Ding-Dong tune.
Modelsthatincludetwopushbuttonswillcomefactorysetforfrontandback
doors.Decalsontherearofthepushbuttonwillindicateitssetting.
Tune Setting
PushButtonSet
forTwoNoteTune
(Ding-Dong)
-6-
598-1109-06
Troubleshooting
Whenthepushbuttondesignatedforthe“Ding-Dong”
toneispressed,onlya“Dong”notewillplaywhenbatterypowerislowin
chime unit.
B. Chime does not sound:
• Makesurepushbuttonandchimecodesarethesame(seeFigure9).
• Checkorientationofpushbuttonandchimebatteries.(Seediagraminside
push button and chime for correct battery orientation.)
• Checkchargeofpushbuttonandchimebatteries,replaceifnecessary.
Chimeisreceiving
interferencefrom another wireless device;change thecode setting (see
Code Settingbelow).

• Donotmountchimeorpushbuttononmetalornearmetalstuds.This
reducesthetransmitterrange.Use1/4"to1/2"(6to13mm)woodshims
to move chime or push button off metal surface.
• Concreteoorsmayreducerange.Movechimeawayfromoor.
• Trylocatingchimeclosertopushbutton.
E. Code Setting:
It is recommended to only change one code position at a time and then check
to see if system is functioning properly.
1. Openthecasesandlocatethejumpersonthepushbuttonandtheswitches
onthechime(seeFigure9).
2. Thepushbuttonhaseightdifferentjumperlocationsandthechimehasseven
switches.Jumperpositions1through7onthepushbuttonandtheswitches
on the chime are used for setting the code.
3. Tochangethecode,either:
• Addajumpertothepushbuttonandsetthematchingchimeswitchto
“ON”or...
• Removeajumperonthepushbuttonandsetthematchingchimeswitch
to“OFF”or...
• Moveajumperonthechimefromonelocationtoanother.Setthematching
twodipswitchesonthepushbuttontomatchthejumpersettingsonthe
chime.
Example:Inthechime,movethechimejumperatlocation“5”tolocation
“4”.Inthepushbutton,setthe“5”dipswitchtoOFFandthe“4”dipswitch
to ON.
-7-
598-1109-06
* Code Settings 1-7
MustMatchBoth Push
ButtonandChime
Note: Some models might require
the use of tweezers to remove
and replace the jumpers.
Figure 9 - Inside Push Button and Chime
PushButton
Jumperson
Positions5,6,and7
ChimeSwitches
5,6,and7in“ON”
Position
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7
ON
Type “C” Type “C”
Type “C”Type “C”
Note:

Note:Unitwillcomefactorysetwithjumpersinlocations5,6,and7onthe
pushbuttonandswitchlocations5,6,and7inthe“ON”positiononthechime
(seeFigure9).
The range of the wireless chime can vary with location, temperature, and
battery condition.
-8-
598-1109-06
Technical Service


Ifyouexperienceaproblem,followthisguide.Youmayalsowanttovisitour
Websiteat: If the problem persists, call* for assistance
at 7:30AMto4:30PMCST(M-F).Youmayalsowrite*to:
HeathCoLLC
P.O.Box90045
BowlingGreen,KY42102-9045
ATTN: Technical Service
*IfcontactingTechnicalService,pleasehavethefollowinginformationavailable:
Model Number, Date of Purchase, and Place of Purchase.

           
requests.

ThisdevicecomplieswithPart15oftheFCCRulesandRSS-210ofIndustry
Canada.Operationissubjecttothefollowingtwoconditions:(1)thisdevicemay
notcauseharmfulinterference,and(2)thisdevicemustacceptanyinterference
received, including interference that may cause undesired operation.
The user is cautioned that changes or modifications not expressly approved by
the party responsible for regulatory compliance could void the user’s authority
to operate the equipment.
-9-
598-1109-06
HeathCoLLCreservestherighttodiscontinueandtochangespecications
atanytimewithoutnoticewithoutincurringanyobligationtoincorporatenew
features in previously sold products.
ONE YEAR LIMITED WARRANTY
Thisisa“LimitedWarranty” which givesyou specic legalrights.You
mayalsohaveother rightswhichvaryfromstatetostateorprovince
to province.
For a period of one year from the date of purchase, any malfunction
causedbyfactorydefectivepartsorworkmanshipwillbecorrectedat
no charge to you.
Not Covered - Repair service, adjustment and calibration due to misuse,
abuse or negligence, light bulbs, batteries, and other expendable items are
notcoveredbythiswarranty.Unauthorizedserviceormodicationofthe
productorofanyfurnishedcomponentwillvoidthiswarrantyinitsentirety.
Thiswarrantydoesnotincludereimbursementforinconvenience,installation,
setuptime,lossofuse,unauthorizedservice,orreturnshippingcharges.
ThiswarrantycoversonlyHeathCoLLCassembledproductsandisnot
extended to other equipment and components that a customer uses in
conjunctionwithourproducts.
THISWARRANTYISEXPRESSLYINLIEUOFALLOTHERWARRAN-
TIES,EXPRESSORIMPLIED,INCLUDINGANYWARRANTY,REPRE-
SENTATIONORCONDITIONOFMERCHANTABILITYORTHATTHE
PRODUCTSAREFITFORANYPARTICULARPURPOSEORUSE,AND
SPECIFICALLYINLIEUOFALLSPECIAL,INDIRECT,INCIDENTAL,OR
CONSEQUENTIALDAMAGES.
REPAIRORREPLACEMENTSHALLBETHESOLEREMEDYOFTHE
CUSTOMERANDTHERE SHALL BE NO LIABILITYONTHE PART
OF HEATHCOLLCFORANYSPECIAL,INDIRECT,INCIDENTAL,OR
CONSEQUENTIALDAMAGES,INCLUDINGBUTNOTLIMITEDTOANY
LOSSOFBUSINESSORPROFITS,WHETHERORNOTFORESEE-
ABLE.Somestatesorprovincesdonotallowtheexclusionorlimitationof
incidental or consequential damages, so the above limitation or exclusion
may not apply to you.

requests.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Heath Zenith 598-1109-06 User manual

Heath Zenith
Brand
Heath Zenith
Model
598-1109-06
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents