Savant SPK-S1WSW-00 Reference guide

Savant
Brand
Savant
Model
SPK-S1WSW-00
Type
Reference guide

This manual is also suitable for

SPK-S1WSx-xx | 009-1886-00 | 191106 1 of 2 45 Perseverance Way, Hyannis, MA 02601
Copyright 2019 Savant Systems, LLC Savant.com | 508.683.2500
Minimum Support Requirements
Software
Release
da Vinci 9.2
Regulatory
Safety and
Emissions
FCC Part 15B C Tick UL CE
RoHS Compliant
Box Contents
(1) Smart Audio WiSA Sub 1 (SPK-S1WSx-xx)
(2) 2-Pin Screw Down Connector (028-0884-xx)
(1) Power Cord (064-0480-xx)
(1) Quick Reference Guide (this document - 009-1886-00)
Specifications
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity (non-condensing)
Dimensions and Weight with Grille
Height 10.2 in (25.91 cm)
Width 8 in (20.32 cm)
Depth 7.5 in (19.05 cm)
Weight 19.55 lb (9.9 kg)
Power
Input Power
100 - 120V AC (50/60Hz)
220 - 240V (50/60HZ)
Standby Power
Consumption
WiSA input: 2 W
Analog input: 1 W
Operating Parameters
Low Pass Filter 60 - 160 Hz
Low Pass Filter
Slope
12 / 24 dB/octave
Frequency
Range
30hz - 160 hz +/- 0.5 dB
Wattage 200 Watts
Streaming Quality Up to 24 bit / 96kHz High Resolution Audio
Networking
Supported
Standards
WiSA
Input Panel (Bottom)
AC 100-120V
-50/60Hz
220-240V
200W
Min Max
Volume
60
LPF Phase
Trigger
In
IR
In
LPF
12dB/24dB
Power
Mode
Status
Wisa
ResetLFE In
On
Audio Sense
Trigger
160 Hz 0
180
-50/60Hz
Caution: Risk of Electric
Shock - Do Not Open
For Indoor
Use Only
E475835
AV Equipment
!
0981
!
Assembled in China
A B
C D E F G H I J K L
A
AC Power
Input
Main power input.
B
Volume
Control
Adjusts volume.
C
Low Pass
Filter
Adjusts the upper end of frequency
response.
D
Phase Control Used to time-align the output signal from
the WiSA Sub to other speakers.
E
12V Trigger
Input
2-pin screw down connector. Used to
control ON/STANDBY settings based on
12V DC input signal.
F
IR Input 2-pin screw down connector allowing for
IR control.
G
LPF Slope Controls the slope rate upper end
frequency response.
H
Power Mode On: Device is always powered on.
Audio Sense: Power command sent with
active audio signal.
Trigger: Powers on with 12V Trigger Input.
I
LFE Input RCA used for LFE input.
J
Status LED O: Resetting, or is powered up and
booting the embedded firmware.
Green Fast Blinking: Updating.
Green Slow Blinking: Entering or finishing
an update.
Green: Normal operation.
Orange: Critical system error.
Orange Slow Blink: Standby power mode.
K
Reset button Hold for 10 seconds to disconnect
speaker from the network and forget any
associated WiSA devices.
Note: This will place the speaker in
Associate Mode.
L
WiSA LED O: Forced Analog Mode.
Green Fast Blinking: Ready to pair.
Green Slow Blinking: Streaming audio.
Green: WiSA connected.
Orange: Audio is muted.
Orange Slow Blinking: WiSA module reset.
Orange Fast Blinking: Reconnecting.
Savant® Smart Audio WiSA Sub 1 [SPK-S1WSx-xx]
Quick Reference Guide
SPK-S1WSx-xx | 009-1886-00 | 191106 2 of 2 45 Perseverance Way, Hyannis, MA 02601
Copyright 2019 Savant Systems, LLC Savant.com | 508.683.2500
Auto Switch Mode
The default mode for the Smart Audio WiSA Sub 1.
In this mode, the WiSA Sub will switch to WiSA or analog inputs as needed. To enter this mode, press the reset button until the WiSA LED turns
green. This mode will remain active through reboots.
– Both the WiSA and the LFE input are active.
– If a WiSA device is connected, input will automatically switch to WiSA.
– If the WiSA LED transitions to Standby/Reset or Pairing, input will switch back to analog.
– If the user presses and holds reset button, input will be switched to WiSA so that a test tone can be heard.
Forced Analog Mode
The analog-input only mode for the Smart Audio WiSA Sub 1.
To enter Forced Analog Mode, toggle the LFP slope switch 4 times within 10 seconds. This mode will remain active through reboots.
– The LFE input will always be active, and WiSA output will not be active.
– The WiSA LED will be turned o to indicate this mode.
– Press and hold the reset button to place the unit back in Auto Switch mode.
Associate Mode
This indicates the WiSA Sub has not been paired to any WiSA transmitting device. To enter this mode, hold the reset button for 10 seconds. For
information on how to associate the Smart Audio WiSA Sub 1 with a WiSA transmitting device, review the WiSA Setup Guide (009-1903-xx).
The WiSA logo, WiSA, WiSA Ready, and WiSA Certified are trademarks, or certification marks of WiSA LLC. Third-party trade names, trademarks
and product names are the intellectual property of their respective owners.
  • Page 1 1
  • Page 2 2

Savant SPK-S1WSW-00 Reference guide

Savant
Brand
Savant
Model
SPK-S1WSW-00
Type
Reference guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents