2. Handi Treads
  3. NST103748YLB

Handi Treads NST103748YLB, NSN126048BK1, NST103748BK1, NST633748BK1, RNST-100B Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Handi Treads NST103748YLB Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Handi‐Treads Wood Installation
Whatyouwillneed:
●YourHandiTread(s)andincludedscrews
●Apowerdrillorascrewdriver
●Atapemeasure
1.AlignyourHandiTreadinthedesiredstairposition.Ifyouareinstallingatread,setitbackroughly½”
fromtheedge.Ifyouareinstallinganosing,makesureitfitssnuglyattheedgeofyourstair.

2.Startingwiththemiddlescrewholes,drillyourscrewsintothestairworkingyourwayoutfromthecenter.
Makesurethatyouaredrillingperpendiculartothesurfaceandthatyouuseallofthescrewholesprovided.
Installationiscompleteonceallscrewshavebeendrilledintoplace.Notethatthescrewholesarenot
raised;DONOTusetheraisedtractionbumpsforyourscrewplacement.

Handi‐Treads Concrete Installation
Whatyouwillneed:
●YourHandiTread
●Clearliquidsilicone(OPTIONAL)
●3/16”drivepinanchors
●3/16”masonrydrillbit
●Ahammer
●Apowerorhammerdrill
Werecommendusingahammerdrillbutapowerdrillwilldothejob.TypesofFastenersHandiTreadsrecommendsusingdrive
pinstofastenyourtreadstoyourstairs.Ensurethateachdrivepinisatleast¾”long.
HandiTreadConcreteStairInstallation
1.Onceyouhaveacquiredallofthenecessarymaterials,alignthetreadinthedesiredposition.Ifyouareinstallinganosing,make
surethatitfitssnuglyattheedgeofthestair.Ifyouareinstallingatread,setitbackroughly½”fromtheedge.Usingamarkerand
thetreadasatemplate,placeadotineachofthepinholestomarktheplacementofthedrivepinsontheconcretesurface.Note
thatthepinholesarenotraised,DONOTusetheraisedtractionbumpsforyourpinplacement.
2.Removethetreadfromthestair.Usinga3/16”masonrydrillbitandyourhammer/powerdrillateachmarkedspot,drillaholeinto
theconcretedeepenoughtoaccommodatethelengthoftheconcretedrivepinyouareusing.Makesurethatyouaredrilling
perpendiculartothesurface.Usecautionwhendrillingtheholes.Iftheconcreteisnotingoodconditionoryouaredrillingtooclose
totheedge,theconcretecanfracture.Thiswouldpreventyoufromusingthislocationandwillnecessitatetheneedtorelocatethe
tread.Toensurethatyouaredrillingdeepenough,attachapieceoftapetothedrillbitattheheightofyourscrew.Forexample,if
youareusingapinthatis¾”long,attachthetape¾”abovethetipofthebit.
Inthepicturebelow,thetapehasreachedthesurface,indicatingthattheholeisattheperfectdepth.

3.Makesurethattheholesyouhavedrilledarefreeofanyconcretedebris.
OPTIONAL:Depositasmallamountofclearsiliconeintoeachdrilledhole.
Asthepinsareplacedintheirpositions,theexcesssiliconewillflowoutoftheholeleavingyouwithawatertightseal.Thismeasure
istakentopreventanywaterfromcollectingwithinthepinhole,whichmightcausetheconcretetofractureifitfreezesandexpands.
4.Placethetreadbackinposition,makingsurethateachpinholeisaboveeachdrilledhole,thenplaceadrivepinineachofthe
pinholes.Startinginthecenterofthetread,workyourwaytotheoutside,hammeringeachpinintoitsrespectivehole.Installationis
completewhenallofthedrivepinshavebeenhavebeenhammeredintoposition.
/