Hanover HANGAZ10X10-GRY Installation guide

polycarbonate panels.

Do not tighten the steps in the Aluminum Pavilion until completing on the assembly of the

You must read these instructions carefully before you start to assemble this pavillon.Please ensure that you find all parts

9820401-1

size/cm:297L×297W×196/252H

size/inch:117L×117W×77/99H

Aluminum Pavilion

Instruction manual

IMPORTANT

in the carton box in the correct type and quantity as mentioned in the list illustrated in every page accordingly.

Please carry out the steps in the order set out in these instructions.

Keep these instructions in a safe place for future reference.

9820401-2

with cold clean water.

Aluminum Pavilion needs cleaning, use a mild detergent solution and rinse

Note that the door is hinged on the right hand side and therefore opens to the right space needed.

This is a multi-part assembly, Allow at least 3.5 hours for assembly.

Hot items such as recently used grills, blowtorches etc.must not be stored in the Wall shed.

Keep children away from the assembly area.

5.Electric screwdriver+5mm Hexagon

2.Spanner 10mm/(25/64) (Ratchet Wrench is better)

1.Triangle Stairs≈

9.Percussion bit(10mm)9.Percussion bit(10mm)(25/64)

!

SAFETY ADVICE

We strongly recommend the use of work gloves during assembly.

Do not attempt to assemble the Aluminum Pavilion in windy or wet conditions,

Do not touch overhead power cables with the aluminum profiles.

Always wear shoes and safety goggles when working with extruded aluminum.

The Aluminum Pavilion must be positioned and fixed on a flat level surface.

Do not lean against or push the Aluminum Pavilion during construction.

Do not position your Aluminum Pavilion in an area exposed to excessive wind.

Do not attempt to assemble this Aluminum Pavilion if you are tired ,have taken drugs or

alcohol or if you are prone to dizzy spells.

If using a step ladder or power tools ensure that you follow the manufactures safety advice.

Ensure there are no hidden pipes or cables in the ground before inserting the pegs.

GENERAL ADVICE

Selecting a site-choose a sunny level position away from overhanging trees.

If you are fixing your Aluminum Pavilion directly to a solid concrete foundation use the

pre drilled holes in the metal base supplied.

The component parts should be checked and laid out close at hand.

Keep all small parts(screws etc)in a bowl so they do not get lost.

Keep roof clear of snow and leaves.

CARE & MAINTENANCE

When your

Do NOT use acetone, abrasive cleaners or other special detergents to clean the

clear panels.

TOOLS & EQUIPMENT REQUIRED

Protective Equipment:

1.Helmet

2.Glove

3.Long Sleeve Cotton Overalls

4.Emergency Medicine Cabinet

5.Eye Shield

2.Angle Square

3.Level Meter

-2-

3.Spanner 14mm/(35/64) (Install the expansion screw)

4.Hexagon wrench 5mm(13/64)inch

wrench (suggest)

6.Wooden Mallet

7.Marking Pen

10.Knife

11.Phillips screwdriver

4.9 Feet Height

(13/64)inch

(16.4Feet)

Installation Tool:

Dispose of all plastic bags safely and keep them out of reach of children.

1.Tape Measure

Measurement Tools:

be caused from screws facing into month.

screws that might hurt your eyes, and avoid suffocation that may

5.Avoid looking up while working high up and avoid dropping

4. Wear long sleeve cotton overalls,gloves and helmet during

of them and pay high attention to electric safety.

9820401-2

9820401-1

7.If injuries occur, please take immediate action to

196cm / 77inch

297cm / 117inch

OTHER CAUTIONS

PRODUCT SIZE

-3-

!

OTHER CAUTIONS

1. 4-5 people required, one is for measuring & taking marks to

ensure the installation dimension ,the second person is

responsible for the installation and the last one do as assistant

and assure the safety.

2. High-power electric tools are required, ensure the normal work

3. Be careful when using the kind of blunt tools, like hammer.

installation and wear safety glasses when using power tools .

6. No climbing, No standing on the tent to avoid falling down.

297cm / 117inch

256cm / 100.8inch

200cm / 78.7inch

252cm / 99.2inch

locate and use a first-aid kit. In case of emergency,

please go to the nearest emergency room.

Make sure to install at the right location

/ 59"

1497mm

/ 100"

/ 29.4"

/ 27.8"

/ 76.7"

/ 31.7"

/ 56"

/ 104.7"

/ 76.7"

T4.8(3/16)

PARTS LIST

SKELETON

NO.

1 4

Qty.

2 4

1950mm

10 8

SCREW

11 8

2660mm

1423mm

806mm

5 4

8L 4

8R 4

6 4

12 4

CONNECT

B1 1

B2 1

B3 1

B5 4

B6 4

B8 8

B9 4

B10 12

B11 4

B12 4

SUMMARY STATEMENT FOR POLYCARBONATE PANEL

OTHER

P1L

P1R

P3L

P3R

x4

F1 48

F2 76

F3 12

F4 8

F5 32

B15 12

S6 112

S8 12

比例

25.400

比例 25.400

比例

25.400

比例 25.400

比例

25.400

比例 25.400

比例

25.400

2548mm

706mm

748mm

B13 8

F6 2

S9 48

M6(15/64)

M8(5/16)

T5(13/64)

M4(5/32)

M6(15/64)

806mm

/ 31.7"

Schematic diagram of connections

Schematic diagram of frames

-5-

B9

6

8L

8R

1

2

5

8L

8R

8L

8R

8L

8R

8L

6

10

11

12

B2

B1

B3

B5

B6

B8

B9

B10

B13

B12

B15

10

B11

B5

B8

1

2

B2

B1

B3

B9

6

5

B8

2

12

B6

6

B13

1

B12

B15

1

Face the white film side of panels towards the sun as they are UV-protected.

"hexagonal screw" installation

Place the "hexagonal screw"into the groove,turn clockwise

until it stops turning.

Adjust the "hexagonal screw"by hand and twist so threads fix

it in place.

Place other parts on "screw"and assemble nut .

SUMMARY STATEMENT FOR POLYCARBONATE PANEL

UV

-6-

-7-

x4

Ⅰ

x4

Ⅱ

F2 x28

1 x4

B5 x4

B12 x4

F2

B5

1

F2

Ⅲ

x4

B12

F2

1

Ⅳ

12 x4

B13 x8

-8-

F5 x 16

S6 x112

2

12

F5

B13

x4

Ⅰ

x8

Ⅱ

S6 x14

12

B13

F5

12

F5

B13

2

Ⅰ

Ⅱ

F5x4

12

2

2 x4

Ⅲ

x4

2

Ⅲ

B8 x8

F2 x32

x4

Ⅰ

B8

2

1

B5

B8

2

x2

Ⅱ

F2

B8

x4

Ⅰ

B8

F2

2

x2

Ⅱ

1

B8

Ⅲ

x2

Ⅲ

x2

Ⅱ

Ⅲ

x2

B5

F2

2

1

-9-

Connection among columns,

beams and studdles.

Don't completely tighten all screws.

F2 x8

Ⅱ

x2

Ⅰ

Ⅱ

F2

B5

2

F2

1

B8

B5

-10-

Make sure the columns are vertical

to the ground,and beams are horizotal.

Tighten all screws by diagonals.

F2 x8

F1 x8

B6 x4

1

B8

F2

x4

Ⅰ

B6

x4

Ⅱ

2

1

B6

-11-

Do not tighten F1.

Preparation: Reserve F1 Screws before installing the roof.

!

B1

F1 x4

F1

B1

-12-

Skeleton Assembly.

5 x4

6 x4

F4 x8

6

5

B1

6

B1

F4

F1

6

F4

B1

F4 and F1 need tighten

!

x4

Ⅰ

x4

Ⅱ

F4

5

B1

-13-

Do not tighten F1

Roof stators installation

F1 x20

B9 x4

6

5

B9

B1

Ⅰ

x4

B9

F1

!

x4

Ⅱ

F1

6

F1

-14-

F1

5

B9

Ⅲ

x4

5

B9

F1

761mm

!

761mm

!

761mm

!

761mm±3

!

5

B9

F1

B9

6

B9

x4

Ⅳ

F1

F1 need tighten

!

30inch

30inch±0.1

B2

B3

-15-

F6 x2

B1

B2

B1

F6

B3

B2

B1

Roof cap installation

-16-

Roof Installation

Team Work Required (2 or 3 persons)

!

180°

-17-

F1 x8

F1

Ⅰ

x4

5

6

5

F1

x4

Ⅱ

F1

6

B6

126±3mm

5

B5

F1 need tighten

!

6

154±3mm

F1 need tighten

!

4.96±0.1inch

6±0.1inch

Make sure the measurements

below are in tolerances.

-18-

8L x4

8R x4

8L

8R

8L

8R

8L

8R

F1 x8

Ⅰ

x4

2

12

F1

2

F1

!

Ⅰ

8L

12

2

12

8R

x4

Ⅱ

2

8L

8R

F1

B9

F1

B9

Ⅲ

x4

F1 need tighten

!

8L

8R

6

B9

Studdles Installation

Do not tighten F1.

-19-

P1L

P1R

P3L

P3R

x4

!

PC Panels Installation

Face the UV surface of the panels towards the sun

PC Panels Holders and Plastic end caps installation

-20-

10 x8

11 x8

B10 x12 B11 x4

10

11

B10

B11

Ⅰ x4

x8

Ⅱ

Ⅲ

x4

B10

10

5

Ⅰ

Ⅱ

Ⅲ

Ⅱ

Ⅲ

5

F5 x 16

B10

10

11

8R

8L

8R

6

11

B11

F5

x4

Page is loading ...

Hanover HANGAZ10X10-GRY Installation guide

This manual is also suitable for

Hanover HANGAZ10X10-GRY Installation guide

Related papers

Other documents