VONN Lighting VRP29104BL Installation guide

Brand
VONN Lighting
Model
VRP29104BL
Type
Installation guide
Installation Guide
ON
© VONN Lighting,2019
Model:VRP29104
Tools You May Need
GOGGLES
TAPE MEASURE
RUBBER
GLOVES
PHILLIPS
LADDER
DRILL
SCREW DRIVER
Circuit Box
Make sure that you have all necessary parts by checking the parts list. If
any part is missing or damaged, please contact VONN Lighting
Customer Service at 888-604-8666 for a replacement.
Please read and comprehend the entire manual before attempting to
assemble, operate, or install the product.
VONN highly recommends to use a qualified, licensed electrician to install
the fixture.
VONN recommends to install the fixture on its own independent circuit.
Do not install the fixture on the same circuit with other appliances, or
HVAC systems.
LED INFO & WARNINGS
•
•
All parts must be used as indicated in these instructions. Do not substitute
any parts, leave parts out, or use any parts that are worn or broken.
•
Inspect the LED fixture prior to installation to make sure that it has not
been damaged during shipping.
•
Please handle the LED light with care when unpacking. Do not apply
pressure to the LEDʼs, do not open any factory sealed compartments, and
do not touch the LEDs with your hands.
•
•
Place the wall switch in the “OFF” position of the room you are installing
the fixture.
•
Shut “OFF” the electricity at main fuse box.
•
VONN recommends ELV (Electric Low Voltage) type dimmers for this
fixture.
•
•
Do not remove or replace VONN manufactured driver that is provided
with the fixture.
VONN Lighting
Parts List
A.
B.
C.
D.
E.
F.
G.
H. Down Rods
A
F
B
C
D
E
Mounting Bracket
Outlet Screws x 4
Wire Connectors x 3
Ground Screw x 1
Canopy Screws x 3
Canopy
G
Wire Clips x 2 (Located in Canopy)
H
© VONN Lighting,2019
Fixture Diagram
Wire
Connector
D
Canopy
B
Mounting
Bracket
A
Mounting
Bracket
A
Ground
Screw
E
Oulet
Scew
C
Canopy
Screw
F
Wire
Connector
G
Wire
Connector
G
(Located in Canopy)
(Located in Canopy)
Down
Rods
H
© VONN Lighting,2019
Step 1. Install Mounting Bracket
Ceiling
Ceiling
Outlet Box
Outlet Box
Align mounting bracket (A) with outlet box.
Attach mounting bracket (A) to outlet box. Secure with
outlet screws (C).
Mounting
Bracket
A
Oulet
Scew
C
Mounting
Bracket
A
© VONN Lighting,2019
Step 2. Assemble Fixture
Connect down rods (H) together and tight-
en by hand. Connect attached down rods
(H) to connector and secure into canopy
(B).
Down
Rods
H
Canopy
B
Cannector
© VONN Lighting,2019
Ceiling
Step 3. Connect Wires
Supply Wires:
Ground Wires:
Connect Black (Line Wire) from fixture to Black (Hot Wire)
from outlet box.
Connect White (Neutral Wire) from fixture to White (Neutral
Wire) from outlet box.
Connect Bare Copper (Ground Wire) from fixture to Green
or Bare Copper (Ground Wire) from outlet box.
Twist wires together clockwise and secure with wire
connector (D).
Installer Tip (1): If ground wire is not available in outlet
box, then secure Bare Copper (Ground Wire) from fixture to
ground screw (E) on mounting bracket (A).
Installer Tip (2): It is recommended that two installers are required to
install the fixture. One installer to hold the fixture, and the second installer
to connect the wires.
Wire Connector
D
White
(Neutral Wire)
Black
(Line Wire)
Bare Copper
(Ground Wire)
Wire
Connector
G
Wire
Connector
G
(Located in Canopy)
(Located in Canopy)
Ground
Screw
E
Canopy
B
Fixture Wires:
Insert wire from fixture into wire connector (G) attached to
driver located in canopy (B).
Step 5. Turn Power ON
© VONN Lighting,2019
Turn electricity “ON” at main fuse box.
Place the recommended ELV type dimmer switch in the “ON” position to test the fixture.
ON
ON
Circuit Box
Ceiling
Ceiling
Mounting
Bracket
A
Step 4. Mount Fixture
Attach canopy (B) to mounting
bracket (A). Secure with canopy
screws (F).
Mounting
Bracket
A
Outlet Box
Canopy
Screws
F
Canopy
Screws
F
Canopy
B
© VONN Lighting,2019
Closed View
Opened View
Installer Tip (3): Separate the rings one by one using both
hands. DO NOT USE EXCESSIVE FORCE.
Step 6. Open Fixture
© VONN Lighting,2019
1
4
2
5
3
6
The fixture has a standard height of
48.50"; however, an extra down rod is
added to provide a total length of
60.50", if needed.
Remove wire from wire connector (G).
G
1. Unscrew down rod (H) from
connector (B).
2. Pull wire out of canopy and
connector (B).
3. Snake wire through extra down
rod (H) and connector (B).
H
B
Secure and tighten addtional down rod
(H).
H
G
Reconnect wire to wire connector (G).
1232mm
48.50”
1537mm
60.50”
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

VONN Lighting VRP29104BL Installation guide

Brand
VONN Lighting
Model
VRP29104BL
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents