Moog Videolarm FDP75C2N Product Instructions

Brand: Moog Videolarm

Model: FDP75C2N

Category: Security camera accessories

Type: Product Instructions

This manual is also suitable for

FusionDome FDW75C2N

Moog Videolarm FDP75C2N provides ready-to-use network camera housing for enhancing home security. This camera provides continues protection with IP PTZ cameras and an inbuilt heater and blower system. The camera is equipped with two 120 to 24Vac, 40Va transformers for supplying power to the accessories and camera. With simple mounting on walls or ceilings, Moog Videolarm FDP75C2N offers flexible installation options.

- 1 -

Before attempting to connect or operate this product,

please read these instructions completely.

Product

Instructions

IP Ready

™

Series

FDW75C2N & FDP75C2N

81-IN5358

04/12/06

- 2 -

SAFETY PRECAUTIONSIMPORTANT SAFEGUARDS

1. Read Instructions - All the safety and operating instructions

should be read before the unit is operated.

2. Retain Instructions - The safety and operating instructions

should be retained for future reference.

3. Heed Warnings - All warnings on the unit and in the operating

instructions should be adhered to.

4. Follow Instructions - All operating and user instructions should

be followed.

5. Electrical Connections - Only a qualiﬁed electrician should make

electrical connections.

6. Attachments - Do not use attachments not recommended by

the product manufacturer as they may cause hazards.

7. Cable Runs - All cable runs must be within permissible

distance.

8. Mounting - This unit must be properly and securely mounted to

a supporting structure capable of sustaining the weight of the

unit. Accordingly:

a. The installation should be made by a qualiﬁed installer.

b. The installation should be in compliance with local codes.

c. Care should be exercised to select suitable hardware to

install the unit, taking into account both the composition of

the mounting surface and the weight of the unit. Be sure to

periodically examine the unit and the supporting structure to

make sure that the integrity of the installation is intact. Failure

to comply with the foregoing could result in the unit separating

from the support structure and falling, with resultant damages

or injury to anyone or anything struck by the falling unit.

WARRANTY INFORMATION

Videolarm, Incorporated warrants that products sold hereunder

shall be ﬁt for the ordinary purpose for which said products

are intended and shall be free from defects in material and

workmanship for a period of two years from date of sale to

buyer. Videolarm makes no other warranty of any kind with

respect to this product, whether expressed or implied, including,

without limitation, the implied warranty of ﬁtness for a particular

purpose.

In the event of a breach of the above warranty, Videolarm shall,

at its option, repair or replace said product. This is Videolarm's

sole obligation under this warranty. In no event shall Videolarm

be liable for any incidental or consequential damages, as deﬁned

in section 2-715 of the Uniform Commercial Code by a breach

of this warranty.

Videolarm shall repair or replace defective products upon shipment

of products prepaid to Videolarm, Inc., 2525 Park Central Blvd.,

Decatur, GA 30035.

Repairs made necessary by reason of accident, misuse or normal

wear shall be charged at Videolarm's standard rate. This warranty

gives you speciﬁc legal rights, and you may also have other rights

which vary from state to state.

UNPACKING

Unpack carefully. Electronic components can be damaged if

improperly handled or dropped. If an item appears to have been

damaged in shipment, replace it properly in its carton and notify

the shipper.

Be sure to save:

1. The shipping carton and packaging material. They are the safest

material in which to make future shipments of the equipment.

2. These Installation and Operating Instructions.

SERVICE

If the unit ever needs repair service, the customer should contact

Videolarm (1-800-554-1124) for authorization to return and shipping

instructions.

TECHNICAL SUPPORT

If technical support is needed, Videolarm has set-up a 24 hour

technical support line for their customers.

1-800-554-1124

CAUTION: TO REDUCE THE RISK OF

ELECTRICAL SHOCK, DO NOT EXPOSE

COMPONENTS TO WATER OR MOISTURE.

The lightning ﬂash with an arrowhead symbol,

within an equilateral triangle, is intended to alert the

user to the presence of non-insulated "dangerous

voltage" within the product's enclosure that may

be of sufﬁcient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

appliance.

24 HOUR TECHNICAL SUPPORT

CAUTION

RISK OF

ELECTRIC SHOCK!

- 3 -

ELECTRICAL SPECIFICATIONS (OUTDOOR ONLY):

Power 24Vac, Class 2 Only

Total Power: 52 watts

Accessories (Heater/Blower): 26 watts

Heater: 25 watts

Blower: 1 watt

Camera Power: 26 watts

NOTE: This unit is designed for operation in an

upright position. Installing the housing

upside down may cause damage to

the internal equipment, and will void the

warranty.

Be sure the bracket is properly and securely mounted

to a supporting structure capable of rigidly holding

the weight of the entire unit.

GENERAL INSTRUCTIONS:

Tools Required: .100" Flat Head Screwdriver

Phillips Head Screwdriver

FDW75CN2, FDP75CN2

IP Ready Network Housing

IP Ready Network Housing with 24Vac input, wall mount or

pendant mounting, heater & blowers, ready for standard IP

PTZ cameras. Includes (2) 120 to 24Vac, 40Va transformers.

NOTE: (2) 40Va transformers are provided for

Accessory and Camera Power.

ASSEMBLING THE UNIT:

1. Remove content from all boxes.

Contents should include:

Main Housing Assembly

Either with wall mount or pendant bracket

Dome Assembly - Clear or Tinted

Do not remove the protective ﬁlm until the product is

assembled and installed.

3 Packet Assemblies

(2) 40Va Transformers

- 4 -

INSTALLATION OF PTZ CAMERA

See model for speciﬁc instruction.

Listed on the following pages are the speciﬁc instructions

for each of the individual network cameras. See speciﬁc

instruction for the model that matches the unit you have.

INDEX OF CAMERAS

AXIS 213 5

AXIS 214 6

AXIS 231D/232D 7-9

CANON VB-C10R 10

CANON VB-C50iR 11

CANON VC-C4R / VC-C50iR 12

ELMO PTC-200C 13

ELMO PTC-201 14

ELMO PTC-400C 15

ELMO PTC-401 16

JVC VN-C30U 17

JVC VN-C625U / TK-625U 18

JVC VN-C655U 19

PANASONIC BB-HCM381 / KX-HMC280 20

PIXORD 261 / 262 21

SONY SNCRZ25 22

SONY SNCRZ30 23

SONY SNCRZ50 24

TOSHIBA IK-WB21A 25

- 5 -

INSTALLING QUICK RELEASE BRACKETS

AXIS 213

2539 Mounting Plate:

1. Install the camera to the 2539 mounting plate using

(2) 10-32 screws and lockwashers provided.

2. The Axis 213 camera requires 3.5" of spacing for optimal

position within the housing. Use (4) 2" spacer(s), plus

(4) 1" spacer(s) and (4) ½" spacer(s) provided in the (2)

hardware packets.

Attach camera using these (2) holes

½"

Captive Screw

(3) screws

in housing

3. Place (3) 8 x 32 x 9Phillips head screws on the top

of the spacer as shown above. Be sure to place the

screws so that they line up with the open slots on the

mounting plate.

4. Slide the mounting plate with camera into position on

top of spacers. Secure 3 screws and captive fastener.

- 6 -

INSTALLING QUICK RELEASE BRACKETS

AXIS 214

2685 Mounting Plate:

Attach camera using these (3) holes

1. Install the AXIS 214 camera to the 2685 mounting

plate using the (3) 3mm x 12mm bolt and lock washers

provided.

2. The AXIS 214 camera requires 2” of spacing for optimal

position within the housing. Use the 4 (2”) spacers

provided in the packet.

3. Place (3) 8 x 32 x 9Phillips head screws on the top

of the spacer as shown above. Be sure to place the

screws so that they line up with the open slots on the

mounting plate.

4. Slide the mounting plate with camera into position on

top of spacers. Secure 3 screws and captive fastener.

- 7 -

INSTALLING QUICK RELEASE BRACKETS

AXIS 231D/232D

2685 Mounting Plate:

Attach camera using these (3) holes

1. The AXIS 231D/232D mounts to the 2685 mounting plate

using the (3) locking pins on the base of the pan tilt.

2. Hold pan/tilt with dome facing down, and ﬁnd “tab” on

the bottom of the unit. Loosen the screw which is to the

right of the tab by approximately 5 turns.

3. Position the locking pins and locking screw over the key

hole slots and twist clockwise. Secure locking screw.

4. The AXIS 231D/232D cameras require ½” of spacing for

optimal position within the housing. Use (4) ½” spacer

provided in the packet.

5. Place (3) 8 x 32 x 9Phillips head screws on the top

of the spacer as shown above. Be sure to place the

screws so that they line up with the open slots on the

mounting plate.

6. Slide the mounting plate with camera into position on

top of spacers. Secure 3 screws and captive fastener.

½"

Keyhole slot (3)

Loosen screw

Locking screw

Small keyhole

slot

Locking pins

- 8 -

Installing the Axis 231D/232D Camera (cont.)

7. Housing with 2685 mounting plate installed.

8. Since the 231D/232D camera operates on 24vac, the power

board that is located inside the housing is not needed. The

remove the power board, start by loosening the screws

on the terminal block and disconnect the orange and red

wires.

9. With a Phillips head screwdriver remove the (4) machine

screws holding the power board to the base bracket.

10. Locate the connector

block, which is included

with the camera. Then

locate the connector

block bracket, which

is included with the

housing. Attach the

block to the bracket as

shown in the following

diagram. Use the M3

screws and washers

that are located in the

housing packet.

11. Attach the connector block assembly to the housing using

(1) 6-32x3/8” screw and star washer located in the housing

packet.

Machine screws (4)

Base Bracket

- 9 -

Installing the Axis 231D/232D Camera (cont.)

13. To manage the input cable running from the connector

block to the camera use the (2) cable tie mounts and

cable ties that are located in the housing packet.

12. Make wiring connections to connector block assembly per

camera instructions.

For Model 25733 only

CONTROL

RJ45 Ethernet Connector

ALARMS

1 Alarm 1 Blue

2 Alarm 2 Violet

3 Alarm 3 Gray

4 Common White

POWER

1 Camera Power (24VAC) Red

2 Camera Power (24VAC) Orange

14. Now grab the camera assembly and connector the RJ45

cable and the input cable to the camera (see diagram

opposite).

15. Now attach the camera assembly to the housing by sliding

the (3) open screw slots over the screws in the housing.

Slide the bracket forward, and the tighten the captive

screw on the bracket.

Open screw slots

Captive screw

Cable Tie Mounts

Cable Ties

- 10 -

INSTALLING QUICK RELEASE BRACKETS

CANON VB-C10R

2539 Mounting Plate:

1. Install the camera to the 2539 mounting plate using

(2) 10-32 screws and lockwashers provided.

2. The Canon VB-C10R camera requires 4" of spacing for

optimal position within the housing. Use (4) 2" spacer(s),

plus (4) 1" spacer(s) and (4) ½" spacer(s) provided in the

(2) hardware packets.

Attach camera using these (2) holes

3. Place (3) 8 x 32 x 9Phillips head screws on the top

of the spacer as shown above. Be sure to place the

screws so that they line up with the open slots on the

mounting plate.

4. Slide the mounting plate with camera into position on

top of spacers. Secure 3 screws and captive fastener.

Captive Screw

(3) screws

in housing

½"

- 11 -

INSTALLING QUICK RELEASE BRACKETS

CANON VB-C50iR

2539 Mounting Plate:

1. Install the camera to the 2539 mounting plate using

(2) 10-32 screws and lockwashers provided.

2. The Canon VB-C50iR camera requires 3.5" of spacing for

optimal position within the housing. Use (4) 2" spacer(s),

plus (4) 1" spacer(s) and (4) ½" spacer(s) provided in the

(2) hardware packets.

Attach camera using these (2) holes

½"

3. Place (3) 8 x 32 x 9Phillips head screws on the top

of the spacer as shown above. Be sure to place the

screws so that they line up with the open slots on the

mounting plate.

4. Slide the mounting plate with camera into position on

top of spacers. Secure 3 screws and captive fastener.

Captive Screw

(3) screws

in housing

- 12 -

INSTALLING QUICK RELEASE BRACKETS

CANON VC-C4R / VC-C50iR

2539 Mounting Plate:

1. Install the camera to the 2539 mounting plate using

(2) 10-32 screws and lockwashers provided.

2. The Canon VC-C4R / VC-C50iR camera requires 4" of

spacing for optimal position within the housing. Use (4)

2" spacer(s), plus (8) 1" spacer(s) provided in the (2)

hardware packets.

Attach camera using these (2) holes

3. Place (3) 8 x 32 x 9Phillips head screws on the top

of the spacer as shown above. Be sure to place the

screws so that they line up with the open slots on the

mounting plate.

4. Slide the mounting plate with camera into position on

top of spacers. Secure 3 screws and captive fastener.

Captive Screw

(3) screws

in housing

- 13 -

INSTALLING QUICK RELEASE BRACKETS

ELMO PTC-200C

Mounting plate for this unit is included in the housing

packet. Remove existing mounting plate installed in the unit

before proceeding.

2539 Mounting Plate:

1. Place the camera onto the quick release bracket using

the (4) metric 3M Phillips head screws provided with the

kit.

Attach camera using these (4) holes

½"

2. The Elmo PTC-200C camera requires 3.5" of spacing for

optimal position within the housing. Use (4) 2" spacer(s),

plus (4) 1" spacer(s) and (4) ½" spacer(s) provided in the

(2) hardware packets.

- 14 -

INSTALLING QUICK RELEASE BRACKETS

ELMO PTC-201

Mounting plate for this unit is included in the housing

packet. Remove existing mounting plate installed in

the unit before proceeding.

2539 Mounting Plate:

1. Place the camera onto the quick release bracket using

the (4) metric 3M Phillips head screws provided with the

kit.

Attach camera using these (4) holes

½"

2. The Elmo PTC-201 camera requires 2½" of spacing for

optimal position within the housing. Use (4) 2" spacer(s)

plus (4) ½" spacer(s) provided in the (2) hardware

packets.

3. Place (3) 8 x 32 x 9Phillips head screws on the top

of the spacer as shown above. Be sure to place the

screws so that they line up with the open slots on the

mounting plate.

4. Slide the mounting plate with camera into position on

top of spacers. Secure 3 screws and captive fastener.

- 15 -

INSTALLING QUICK RELEASE BRACKETS

ELMO PTC-400C

Mounting plate for this unit is included in the housing

packet. Remove existing mounting plate installed in the unit

before proceeding.

2539 Mounting Plate:

1. Place the camera onto the quick release bracket using

the (4) metric 3M Phillips head screws provided with the

kit.

Attach camera using these (4) holes

½"

2. The Elmo PTC-400C camera requires 3.5" of spacing for

optimal position within the housing. Use (4) 2" spacer(s),

plus (4) 1" spacer(s) and (4) ½" spacer(s) provided in the

(2) hardware packets.

3. Place (3) 8 x 32 x 9Phillips head screws on the top

of the spacer as shown above. Be sure to place the

screws so that they line up with the open slots on the

mounting plate.

4. Slide the mounting plate with camera into position on

top of spacers. Secure 3 screws and captive fastener.

- 16 -

INSTALLING QUICK RELEASE BRACKETS

ELMO PTC-401

Mounting plate for this unit is included in the housing

packet. Remove existing mounting plate installed in

the unit before proceeding.

2539 Mounting Plate:

1. Remove the mounting plate from the camera and

place it onto the quick release bracket using the (4)

metric 3M Phillips head screws provided with the kit.

Then place the ELMO mounting plate back onto the

Elmo PTC-401C.

Attach camera using these (4) holes

2. In the packet, there will be a number of 2 inch and 1

inch spacers. Take four of the 1 inch spacers and screw

them onto the spacers that are on the base bracket

(to make a 3 inch spacer). Place two 8/32 X 9 Philips

head screws on the three inch spacer in the dome. Be

sure to place the screws so they line up with the two

open screw slots on the quick release bracket. Place

the Elmo PTC-401C pan/tilt and quick release bracket

in the housing, sliding the two open screw slots over the

screws in the housing. Slide the bracket forward, and

then tighten the captive screw on the bracket.

- 17 -

INSTALLING QUICK RELEASE BRACKETS

JVC VN-C30U

2539 Mounting Plate:

1. Remove the mounting plate from the camera and

place it onto the quick release bracket using the (3)

metric 3M Phillips head screws provided with the kit.

Then place the mounting plate back onto the

JVC VN-C30U.

Attach camera using these (3) holes

½"

2. In the packet, there will be a number of 2 inch and

½ inch spacers. Take four of the ½ inch spacers and

screw them onto the spacers that are on the base

bracket (to make a 2½ inch spacer). Place two 8/32

X 9 Philips head screws on the two and a half inch

spacer in the dome. Be sure to place the screws so

they line up with the two open screw slots on the quick

release bracket. Place the JVC VN-C30U pan/tilt and

quick release bracket in the housing, sliding the two

open screw slots over the screws in the housing. Slide

the bracket forward, and then tighten the captive

screw on the bracket.

- 18 -

INSTALLING QUICK RELEASE BRACKETS

JVC VN-C625U / TK-625U

Attach camera using these (4) holes

1. Remove plastic cover (1 screw).

2. Detach Q/R Bracket from camera.

2630 Mounting Plate:

3. The JVC VN-C625U / TK-625U requires a total of 2” of

spacing to properly position the camera within the

housing.

4. Attach (4) 1” spacers to the 2630 mounting plate in the

position shown. Secure with (4) 6 x 32 x .5” screws and

lock washers.

5. Place (4) additional spacers on the main bracket as

shown in picture above.

6. Place (3) 8 x 32 x 9Phillips head screws on the top

of the spacer as shown above. Be sure to place the

screws so that they line up with the open slots on the

mounting plate.

7. Slide the mounting plate with camera into position on

top of spacers. Secure 3 screws and captive fastener.

- 19 -

INSTALLING QUICK RELEASE BRACKETS

JVC VN-C655U

2630 Mounting Plate:

1. Place the camera onto the quick release bracket using

the (4) metric 3M Phillips head screws provided with the

kit.

Attach camera using these (4) holes

½"

2. The JVC VN-C655U requires 1 ½ “ to properly position

the camera within the housing. Use (4) 1” spacers and

(4) ½” spacer provided in the (2) hardware packets.

3. Place (3) 8 x 32 x 9Phillips head screws on the top

of the spacer as shown above. Be sure to place the

screws so that they line up with the open slots on the

mounting plate.

4. Slide the mounting plate with camera into position on

top of spacers. Secure 3 screws and captive fastener.

NOTE: The JVC VN-C655U is an 18Vdc unit.

Check instructions for connecting 18Vdc

camera (page xx).

- 20 -

½"

INSTALLING QUICK RELEASE BRACKETS

PANASONIC BB-HCM381 / KX-HMC280

2539 Mounting Plate:

Attach camera using this hole

1. Install the camera to the 2539 mounting plate using the

¼ x 20, washer and lockwasher provided.

2. The Panasonic BB-HCM381 / KX-HMC280 requires 3½"

of spacing to properly position the camera within the

housing.

3. Place (3) 8 x 32 x 9Phillips head screws on the top

of the spacer as shown above. Be sure to place the

screws so that they line up with the open slots on the

mounting plate.

4. Slide the mounting plate with camera into position on

top of spacers. Secure 3 screws and captive fastener.

Page is loading ...

Moog Videolarm FDP75C2N Product Instructions

Brand: Moog Videolarm

Model: FDP75C2N

Category: Security camera accessories

Type: Product Instructions

This manual is also suitable for

FusionDome FDW75C2N

Download PDF

report

Moog Videolarm FDP75C2N Product Instructions

This manual is also suitable for

Moog Videolarm FDP75C2N Product Instructions

Related papers

Other documents