Tyan S1563 User manual

Revision 1.0

Single S1563S/Dual S1563D

Pentium Class 430 HX

75MHz thru 200MHz

PCI-ISA System Board

User's Manual

2S1563-001-01 www.tyan.com

Table Of Contents

1. Introduction....................................................................... 4

1.1 Overview................................................................4

1.2 Hardware Specifications..........................................5

1.3 Software Specifications.......................................... 6

1.4 Environment........................................................... 6

2. Board Installation.............................................................. 7

2.1 Unpacking.............................................................. 7

2.2 Installation.............................................................. 7

3. S1563On Board Resource Settings................................. 8

3.1 S1563Board Layout & Jumper Locations................ 8

3.2 Quick Reference for Jumpers.................................. 9

3.3 CMOS RTC............................................................13

3.4 Speaker Connector..................................................13

3.5 Turbo Switch.......................................................... 13

3.6 Turbo LED Connect................................................13

3.7 Reset Connector..................................................... 14

3.8 Flash EPROM Jumpers.......................................... 14

3.9 CMOS & Password Reset...................................... 14

3.10 DRAM Installation................................................ 15

3.11 CPU Installation.................................................... 18

3.12 Cache Memory.................................................... 19

3.13 Understanding Different Clock Speeds................... 20

3.14 Peripheral Device Installation.................................21

3.15 Connecting The Power Supply...............................22

4. BIOS Configuration...........................................................24

4.1 Entering Setup....................................................... 24

4.2 Control Keys......................................................... 25

4.3 Getting Help........................................................... 26

4.4 The Main Menu...................................................... 26

4.5 Standard CMOS Setup Menu...................................28

4.6 BIOS Features Setup.............................................. 31

4.7 Chipset Features Setup............................................34

4.7.1 Power Management Setup........................39

4.8 PCI Slot Configuration.............................................41

4.9 Integrated Peripherals............................................. 43

4.10 Load Setup Defaults..............................................44

4.11Password Setting................................................... 44

4.12 IDE HDD Auto Detection..................................... 46

4.13 Save & Exit Setup.................................................46

4.14 Keyboard Setting Functions....................................47

3S1563-001-01 www.tyan.com

5.AMI WinBIOS....................................................................48

5.1 Standard Setup Options........................................... 48

5.2 Advanced Setup..................................................... 49

5.3 Advanced Chipset.................................................. 52

5.4 Power Management................................................56

5.5 Peripheral............................................................... 57

5.6 Utility..................................................................... 58

5.7 Security.................................................................. 58

5.8 Defaults................................................................. 58

6. Flash Writer Utility............................................................ 59

6.1 The Flash Memory Writer Utility Screen...................61

7. Timer &DMA Channel Map............................................. 62

7.1 Interrupt Map......................................................... 62

Information presented in this publication has been carefully checked for

reliability; however, no responsibility is assumed for inaccuracies. The

information contained in this document is subject to change without

notice.

Trademarks

Award BIOS/Flash are trademarks of Award Software International Inc.

AMI BIOS is a trademarks of American Megatrends Inc.

IBM,PC,AT,PS/2 are trademarks of IBM Corporation

INTEL,Pentium are trademarks of Intel Corporation.

Cyrix is a trademark of Cyrix Corp.

Copyright c 1996 TYAN Computer Corp.

Tomcat III, S1563.

4S1563-001-01 www.tyan.com

1. Introduction

1.1 Overview

The S1563D is a quality, high performance dual processor mainboard

based on the powerful Intel Pentium microprocessors. This mainboard is

designed around the latest and fastest Intel 430HX(II) chipset and can

support CPU speeds of 75MHz through 200MHz and beyond. The

S1563S is single processor mainboard and the S1563D is a dual processor

mainboard.

The S1563 supports single or dual Pentium and singleCyrix processors,

EDO memory, ECC memory and memory parity checking.The S1563's

PCI Local Bus provides high performance capabilities that are ideal for a

wide range of demanding applications such as: CAD, CAM, CAE,

networking, multi-user environments, database management, desktop

publishing, image processing and 3D animation.

This integrated system board achieves the highest reliability and yet is

small enough for all of its features to be supported in a "Baby-AT" form-

factor. Some of the features included are: on-board dual channel PCI

IDE, on-board floppy controller, on-board high speed I/O, and support for

pipeline-burst SRAM.

Flexibility and expandibility have been designed into the S1563. With I/O

and drive controller support built on-board, the four PCI and five ISA

(One ISA and one PCI as a shared slot) slots are free for any add-on

expansion cards. With eight SIMM sockets, the S1563 can provide a very

flexible memory configuration of 8MB to 512MB of RAM. With the

S1563D's support for dual Pentium processors, you can start a system

with just one CPU, and later add another, when more processing power is

required.

Notice

This board uses the Intel 430HX chipset. According to Intel , the USB

function in this chipset is not guaranteed. Compatibility tests cannot be

conducted for USB at this time due to no availability of such devices

and drives. Please log on to the Tyan web page for the latest infomation.

5S1563-001-01 www.tyan.com

1.2 Hardware Specifications/Features

wCPU Intel Pentium 75 MHz thru 200 MHz (Socket 7)

(Single or Dual CPU configuration)

Cyrix 6x86 P120, P150 and P166(Single Only)

wCoprocessor On-chip floating point unit

wSpeed 50/60/66 MHz system bus

25/30/33 MHz PCI bus

7.5/8.33 MHz ISA bus speed

wDRAM 4 double banks of 72 pin SIMM sockets

Supports 5V or 3.3V memory

Supports EDO(Exended Data Out) DRAMs

Supports ECC(Error Correcting Code)w/ parity

Supports Fast Page Mode DRAMs

Supports 8MB to 512MB of DRAMs

wL2 Cache 512KB on board 2nd level cache memory

Supports synchronous pipeline-burst cache

wEIDE Controller Primary and secondary PCI EIDE channels on

board for support of up to four EIDE Mode 0

through Mode 4 drives.

Supports DMA(Bus Master) mode 1 and 2.

( Bus Master driver on web at www.tyan.com)

wEnhanced I/O Multi-mode bi-directional parallel port that

supports standard, EPP and ECP modes.

Supports 16550 compatible UARTS for on-board

high speed serial ports.

Support for an IrDA compliant InfraRed inter-

face.

On-board floppy controller.

wMouse On-board PS/2 mouse connector.

wI/O Bus Slots 4 Master/Slave PCI-Bus

5 ISA Bus (One ISA and one PCI shared slot)

6S1563-001-01 www.tyan.com

1.3 Software Specifications

wBIOS Licensed Award or AMI BIOS

AT CMOS setup, BIOS/CHIPSET setup,

and hard disk utility included.

Support for easy BIOS upgrades with flash

EEPROM chip.

wO.S. Operates with MS-DOS, Windows 3.x, Windows

for Work Groups 3.x, Windows 95, Windows NT,

OS/2, Novell Netware, Novell UnixWare 1.1 and

SCO Unix.

1.4 Environment

Ambient Temperature 0 to +50 C (operating)

Relative Humidity 0 to +85% (operating)

Altitude 0 to 10,000 feet (operating)

Vibration 0 to 1,000 Hz

Voltage 4.9 to 5.2 V

7S1563-001-01 www.tyan.com

2. Board Installation

2.1 Unpacking

The mainboard package should contain the following:

wS1563 Mainboard

wOne IDE 40 pin cables

wTwo serial cables

wwOne parallel cable

wOne 34 pin floppy cable

wUser's Manual

The mainboard contains sensitive electric components which can be easily

damaged by static electricity, so the mainboard should be left in its original

packaging until it is ready to be installed.

With the power supply pluged in and turned off touch an unpainted area of

the system chassis imedietly before handling the mainboard or any compo-

nent. Doing so discharges the static charge your body may have built.

After opening the mainboard carton, extract the system board holding it by

its edges ,and place it only on a grounded anti-static surface, component

side up. Inspect the board for damage. Press down on all of the socket IC's

to make sure that they are properly seated. Do this only with the board

placed on an anti-static mat. Do not touch the bottom of the board.

DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN

DAMAGED!

2.2 Installation

You are now ready to install your mainboard. The mounting hole pattern of

the S1563 matches the "Baby AT" system board spec. It is assumed that

the chassis is for a standard IBM XT/AT form factor.

8S1563-001-01 www.tyan.com

PCI Slot 1

Bank 0

Bank 1

PCI Slot 2

PCI Slot 4

3. On Board Resource Setting

KB CTR

PWR CON. 5V

ISA Slot 1

ISA Slot 2

ISA Slot 3

ISA Slot 4

ISA Slot 5

Bank 3

Floppy Con.

Keyboard

CON

BIOS

AMI/AWARD

J48

J28

Parallel Port

J1

PS/2

Mouse

Header

1

82039AA

Socket 7

CPU 1

82371SB

Socket 7

CPU 0

RTC

pin 1

IR2

USB1

USB2

J14

PCI Slot 3

J15

J45

J13

pin 1

J29

J30

J31

J32

J33

J34

J35

J36

IR1

J25

J24

J27 J23

J22

J20

J26

pin 1

J50

J46

pin 1

Secondary IDE

Primary IDE

Bank 2

Bank 3

Figure 3.1 S1563 Board Layout

Com1

Com2

pin 1

J16

82439HX

J12

J42

J43

J44

J53

J52

J54

J39

J38

J37

J41

J40

J56

J55

J19

SRAM

J9

J10

J2

J11

Jumper is open/off

Jumper is closed/on

Jumpers shown are

defaults

Only on S1563D

9S1563-001-01 www.tyan.com

APIC For DP: J50 (Dual CPU Jumper for S1563D only)

J50

Dual CPU 2-3 Default

Single CPU 1-2

*Note: When using two Pentiums, Intel recommends that the chips

have the same s-spec number. These numbers are stamped on

the top and bottom or the Pentium chips. Check with your

CPU vendor for more info about s-spec numbers.

3.2 Jumper Settings

CPU Speed: J13 J19 J20 CPU Speed

1-2, 3-4 Off Off 75 MHz

3-4 Off Off 90 MHz

1-2 Off Off 100 MHz

3-4 On Off 120 MHz Cyrix P150+

1-2 On Off 133 MHz Cyrix P166+

3-4 On On 150 MHz

1-2 On On 166 MHz

1-2 Off On 200 MHz

1-2, 3-4 On Off 100MHz Cyrix P120+

DRAM Voltage Setting:J1, J2, J11, J12, J8, J9, & J10

Damage to system can result if these are set incorrectly!

Volts J1 J2 J11 J12 J8 J9 J10

Default 5V On On On On Off Off Off

3.3V Off Off Off Off On On On

CMOS Reset: J46

Off: Normal operation(Default)

On: Clears password and resets CMOS

wWith power off, put jumper on J46 for about 10 seconds.

wRemove jumper and power system on and the CMOS will be reset.

10S1563-001-01 www.tyan.com

I/O Selection: J14 & J15

J14 J15

For COM 1 and 2 1-2 1-2 Default

For InfraRed 2-3 2-3

Speaker Connector: J23

Pinout Assignments

1 Speaker out

2 Ground

3 Ground

4 + 5V

Keylock Connector: J22

Pinout Assignments

Pins 1 to 3 for power LED. 1 Led Output

2 No Connect

3 Ground

Pins 4 and 5 for Keylock 4 Keylock

5 Ground

Turbo Switch: J26 ( Non-Turbo Mode Not Supported )

HDD LED: J24

Pinout Assignments

1 Cathode

2 Anode

3 Cathode

4 Anode

Pins 1 and 2 are for primary IDE channel.

Pins 3 and 4 are for secondary IDE channel.

11S1563-001-01 www.tyan.com

PS/2 Pinout:

Ground Data VCC

Keyboard

Connector

ClK

Reset Connector: J27

Pinout Assignment

1 Power Good

2 Ground

Turbo LED Connector: J25

Pinout Assignment

1 Cathode

2 Anode

Flash EEPROM: J48

This jumper should be left at the factory default.

J48 1-2

InfraRed Interface: Con7 and Con9

Pinout Assignment

1 Signal In

2 Gnd

3 Signal Out

4 VCC

12S1563-001-01 www.tyan.com

CPU Voltage Regulator Settings:

Pentium MMX requires two voltage sources, J60, J61, & J62 are settings for

one source. J63, J64 and J65 are settings for the second voltage source. The

default setting is for P54C/Cyrix CPU's.

P54C(Pentium) & Cyrix P55C(Pentium MMX)

3.6V 3.5V 3.3V 3.0V 2.85V 2.65V

J39 off on off J42 on off off

J38 on off off J43 off off on

J37 off off on J44 off on off

J40 on J40 off

J41 on J41 off

J42 off J52 off Settings for

J43 off Default settings J53 on P55C only

J44 off for P54C and Cyrix J54 on

J52 on

J53 off

J54 off

13S1563-001-01 www.tyan.com

3.3 CMOS RTC

CMOS RTC includes an internal battery and Real Time Clock circuit. It

provides the date and the time for the system. Normally the life span of a

RTC internal battery is 10 years. When replacing, you should use the same

model.

3.4 Speaker Connector Installation

S1563 provides a 4-Pin header (J23) to connect the speaker. The polarity

can go either way.

3.5 Turbo Switch

The front panel on your case may have a turbo switch to control system

speed when slower program execution is required for software developed

in the old XT days.

The Intel 430HX chipset doesn't support a de-turbo mode, but the S1563

has a connector (J26) for the cable that may come with the case.

3.6 Turbo LED Connector Installation

The TURBO LED on the front case panel can indicate the current speed

status of the system. The TURBO LED connector should be installed to

J25 in the correct direction.

14S1563-001-01 www.tyan.com

3.7 Hardware Reset Switch Connector Installation

The RESET switch on your cases' display panel provides users with the

HARDWARE RESET function which is the same as power on/off. The

system will do a cold start after the RESET switch is pushed by the user.

The RESET switch is a 2 pin connector and should be installed on jumper

J27.

3.8 Flash EEPROM-Jumper J48

The S1563 uses flash memory to store BIOS data. It can be updated as

new versions of the BIOS becomes available. The flash utility will guide

you through the process step by step. If your system is functioning properly,

you may want to forego updating your BIOS in the event the new one

causes problems with your existing hardware and software.

J48 determines which type of EPROM is used. This jumper have been

set to match the on board BIOS chip. The factory default for the S1563 is

on pins 1-2.

Refer to chapter 6 for Flash EEPROM upgrade procedures.

3.9 Hardware CMOS & Password Reset

(The following steps are valid provided the board has a DS12887A RTC)

If you have been locked out of your system because you forgot your pass-

word or set the CMOS incorrectly, follow the instructions below.

a. Power off the system

b. Short jumper J46.

c. Wait for 5 seconds then remove the jumper from J46.

d.Then power on the system again.

By doing the above procedures, your password will be erased and the CMOS

will be reset to the BIOS defaults.

15S1563-001-01 www.tyan.com

3.10 DRAM Installation

The S1563 uses a 64-bit data path from memory to CPU and can

accommodate up to 512 MB of RAM. The mainboard supports

standard, EDO (Extended Data Out) and ECC(Error Correcting Code)

72 pin SIMMS . All installed memory will be automatically detected so

there is no need to set jumpers.

wSIMM modules must be installed in pairs.

wEach pair of SIMMs must be of the same size and type.

wThe mainboard supports 1, 2, 4, 8 and 16MBx32 SIMMS.

wThe table below shows some of the available memory configurations.

Total Memory In Bank

Bank0 Bank1 Bank2 Bank3 0 0&1 0,1&2 Total

1MB*2 (1MB*2) (1MB*2) (1MB*2) 2MB 4MB 6MB 8MB

1MB*2 (2MB*2) (2MB*2 (2MB*2) 2MB 6MB 10MB 14MB

1MB*2 (4MB*2) (4MB*2) 4MB*2) 2MB 10MB 18MB 26MB

1MB*2 (8MB*2) (8MB*2) (8MB*2) 2MB 18MB 34MB 50MB

1MB*2 (16MB*2) (16MB*2) (16MB*2) 2MB 34MB 66MB 98MB

1MB*2 (32MB*2) (32MB*2) (32MB*2) 2MB 66MB 130MB 194MB

1MB*2 (64MB*2) (64MB*2) (64MB*2) 2MB 130MB 258MB 386MB

2MB*2 (1MB*2) (1MB*2) 1MB*2) 4MB 6MB 8MB 10MB

2MB*2 (2MB*2) (2MB*2) (2MB*2) 4MB 8MB 12MB 16MB

2MB*2 (4MB*2) (4MB*2) (4MB*2) 4MB 12MB 20MB 28MB

2MB*2 (8MB*2) (8MB*2) (8MB*2) 4MB 20MB 36MB 52MB

2MB*2 (16MB*B) (16MB*2) (16MB*2) 4MB 36MB 68MB 100MB

2MB*2 (32MB*2) (32MB*2) (32MB*2) 4MB 68MB 132MB 196MB

2MB*2 (64MB*2) (64MB*2) (64MB*2) 4MB 132MB 260MB 388MB

16S1563-001-01 www.tyan.com

4MB*2 (1MB*2) (1MB*2) (1MB*2) 8MB 10MB 12MB 14MB

4MB*2 (2MB*2) (2MB*2) (2MB*2) 8MB 12MB 16MB 20MB

4MB*2 (4MB*2) (4MB*2) (4MB*2) 8MB 16MB 24MB 32MB

4MB*2 (8MB*2) (8MB*2) (8MB*2) 8MB 24MB 40MB 56MB

4MB*2 (16MB*2) (16MB*2) (16MB*2) 8MB 40MB 72MB 104MB

4MB*2 (32MB*2) (32MB*2) (32MB*2) 8MB 72MB 136MB 200MB

4MB*2 (64MB*2) (64MB*2) (64MB*2) 8MB 136MB 264MB 392MB

32MB*2 (1MB*2) (1MB*2) (1MB*2) 64MB 66MB 68MB 70MB

32MB*2 (2MB*2) (2MB*2) (2MB*2) 64MB 68MB 72MB 76MB

32MB*2 (4MB*2) (4MB*2) (4MB*2) 64MB 72MB 80MB 88MB

32MB*2 (8MB*2) (8MB*2) (8MB*2) 64MB 80MB 96MB 112MB

32MB*2 (16MB*2) (16MB*2) (16MB*2) 64MB 96MB 128MB 160MB

32MB*2 (32MB*2) (32MB*2) (32MB*2) 64MB 128MB 192MB 256MB

32MB*2 (64MB*2) (64MB*2) (64MB*2) 64MB 192MB 320MB 448MB

16MB*2 (1MB*2) (1MB*2) (1MB*2) 32MB 34MB 36MB 38MB

16MB*2 (2MB*2) (2MB*2) (2MB*2) 32MB 36MB 40MB 44MB

16MB*2 (4MB*2) (4MB*2) (4MB*2) 32MB 40MB 48MB 56MB

16MB*2 (8MB*2) (8MB*2) (8MB*2) 32MB 48MB 64MB 80MB

16MB*2 (16MB*2) (16MB*2) (16MB*2) 32MB 64MB 96MB 128MB

16MB*2 (32MB*2) (32MB*2) (32MB*2) 32MB 96MB 160MB 224MB

16MB*2 (64MB*2) (64MB*2) (64MB*2) 32MB 160MB 288MB 416MB

8MB*2 (1MB*2) (1MB*2) (1MB*2) 16MB 18MB 20MB 22MB

8MB*2 (2MB*2) (2MB*2) (2MB*2) 16MB 20MB 24MB 28MB

8MB*2 (4MB*2) (4MB*2) (4MB*2) 16MB 24MB 32MB 40MB

8MB*2 (8MB*2) (8MB*2) (8MB*2) 16MB 32MB 48MB 64MB

8MB*2 (16MB*2) (16MB*2) (16MB*2) 16MB 48MB 80MB 112MB

8MB*2 (32MB*2) (32MB*2) (32MB*2) 16MB 80MB 144MB 208MB

8MB*2 (64MB*2) (64MB*2) (64MB*2) 16MB 144MB 272MB 400MB

Total Memory In Bank

Bank0 Bank1 Bank2 Bank3 0 0&1 0,1&2 Total

17S1563-001-01 www.tyan.com

64MB*2 (1MB*2) (1MB*2) (1MB*2) 128MB 130MB 132MB 134MB

64MB*2 (2MB*2) (2MB*2) (2MB*2) 128MB 132MB 136MB 140MB

64MB*2 (4MB*2) (4MB*2) (4MB*2) 128MB 136MB 144MB 152MB

64MB*2 (8MB*2) (8MB*2) (8MB*2) 128MB 144MB 160MB 176MB

64MB*2 (16MB*2) (16MB*2) (16MB*2) 128MB 160MB 192MB 224MB

64MB*2 (32MB*2) (32MB*2) (32MB*2) 128MB 192MB 256MB 320MB

64MB*2 (64MB*2) (64MB*2) (64MB*2) 128MB 256MB 384MB 512MB

Total Memory In Bank

Bank0 Bank1 Bank2 Bank3 0 0&1 0,1&2 Total

18S1563-001-01 www.tyan.com

3.11 CPU Installation

Many types of Pentiums (75 thru 200 MHz) and Cyrix CPUs can be

used on the S1563. Please refer to the previous pages for the correct CPU

jumper settings for your board.

w The CPU is a sensitive electronic component and it can be easily

damaged by static electricity. Do not touch the CPU pins with your

fingers.

w When installing the CPU into the socket, match the CPU pins to the

socket pins.

w Before the CPU is installed, the mainboard must be placed on a flat

plane. You should be able to insert the CPU with minimal pressure.

Do not push down hard, use firm pressure.

w A cooling fan and heat sink assembly is required to protect the

CPU from being damaged.

1. Make sure the ZIF socket lever is up. To raise the lever, pull it out

to the side a little and raise it as far as it will go. The top plate will

slide back.

2. Align the CPU and socket Pin 1 corners. The pins on the bottom

should align with the rows of holes in the socket.

3. Insert the CPU in the socket. It should insert easily. If it does

not, adjust the position of the lever a little.

4. Press the lever down. The top plate will slide forward. You will

feel some resistance as the pressure starts to secure the CPU in

the socket. This is normal and will not damage the CPU.

The lever should snap into place at the side of the socket.

19S1563-001-01 www.tyan.com

3.12 Cache Memory

The S1563 comes with 512Kb of L2 synchronous pipeline burst SRAM.

The S1563's L2 cache is surface mounted and can be enabled or dis-

abled through the BIOS setup.

wThe BIOS will auto detect the cache size so a you don't need to change

any jumpers.

wThe mainboard has an 11 bit tag built on board so cachability of main

memory is to 512MB.

20S1563-001-01 www.tyan.com

3.13 Understanding The Different Clock Speeds

The following chart shows the different CPU, mainboard and PCI fre-

quencies. As you may have noticed, all the Intel Pentium CPUs use an

internal clock multiplier(x3, x2.5, x2 or x1.5 Motherboard speed). All

Cyrix 6x86 can only use a x2 clock mulitipplier.

Pentium Mainboard PCI Bus

Internal Clock Clock Clock

75 MHz 50 MHz 25 MHz

90 MHz 60 MHz 30 MHz

100 MHz 66.67 MHz 33 MHz

120 MHz 60 MHz 30 MHz

133 MHz 66.67MHz 33 MHz

150 MHz 60 MHz 30 MHz

166 MHz 66.67 MHz 33 MHz

200 MHz 66.67 MHz 33 MHz

In the table above, the 50, 60 and 66.67 MHz figures are oscillator speeds

that establish the external clock speed. The PCI Bus clock speed is fixed at

one half of the mainboard clock speed. The 150MHz Pentium when set for

2.5x mode will achieve a 30MHz PCI bus speed but if it is set for 3x mode

you will get a slower 25MHz PCI bus speed.

Since all of the Cyrix 6x86 CPU's use a x2 mulitplier, the 100MHz P120+

must run on a 50MHz host bus. The PCI speed will then be at 25MHz.

Page is loading ...

Tyan S1563 User manual

This manual is also suitable for

Tyan S1563 User manual

in other languages

Related papers

Other documents