La Crosse Technology RADIO CONTROLLED PROJECTION ALARM CLOCK Owner's manual

Brand: La Crosse Technology

Model: RADIO CONTROLLED PROJECTION ALARM CLOCK

Category: Alarm clocks

Type: Owner's manual

This manual is also suitable for

433 MHz RADIO CONTROLLED PROJECTION

ALARM CLOCK

Instruction manual

INTRODUCTION:

Congratulations on purchasing this innovative 433MHz Projection alarm clock which

also displays indoor temperature and humidity. To enjoy the full benefits of this

innovative product, please read this operating manual.

Adapter

socket

Stand

Battery

com

artment

LCD

Dis

Function

FEATURES

• Radio-controlled time and date

• Projection of time

• EL backlight

• Displays time with seconds, indoor temperature & humidity

• Time alarm wit snooze h

• Table-standing

TO INSTALL AND REPLACE BATTERIES IN THE PROJECTION ALARM

The Projection Alarm uses 2 x AA, IEC LR6, 1.5V batteries. To install and replace the

batteries, please follow the steps below:

1. Insert finger or other solid object in

the space at the bottom center of the

battery compartment and lift up to

remove the cover.

2. Insert batteries observing the correct

polarity (see marking).

3. Replace compartment cover.

In addition or instead of inserting batteries, the AC adapter can be used:

1. Connect the power adapter to a wall socket

2. Insert the adapter into the jack at the bottom of the clock

3. The Projection clock will now start receiving the DCF time signal. After

approximate 3 to 5 minutes, the DCF time will be displayed (see Notes at below

clause).

Important!

Use only the adapter provided with the projection clock and make sure that your

household voltage is appropriate to the working voltage of the transformer. Otherwise

your projection clock may be damaged.

BATTERIES POWERED WITH THE USE OF AC/DC ADAPTER

If the Projection clock is first powered by batteries and the power adapter is

subsequently used for extended period of time, the main power source of the Projection

clock will switch to AC/DC power. The batteries will then act as a backup power source

in case of power failure.

Notes:

• After the projection clock is powered, there will be a beep sound and the LCD

(Liquid Crystal Display) will activate.

• The indoor temperature/humidity and the remote temperature will be displayed.

Also, the time will be displayed as 0:00.

• The DCF time reception will automatically be initiated, and a tower icon will

appear (no tower icon will appear if the time reception is too weak to be detected,

and the time display will start from 0:00).

• When DCF time has not been received, user may use the MODE/MIN key to

manually enter a time and date initially. The clock will automatically attempt to

receive the DCF time at each full hour. When this is successful, the received time

will override the manually set time. The date is also updated with the received

time. (Please refer also to notes on “DCF-77 RADIO CONTROLLED TIME” and

“Manual time setting”).

TO RESET THE PROJECTION CLOCK

To reset the Projection clock to the factory default setting or in case of a malfunction,

please remove all batteries from the unit and unplug the AC/DC adapter from any

power source. Wait at least for 3 minutes before powering up the Projection clock

again.

BATTERY CHANGE:

It is recommended to replace the batteries in all units on an annual basis to ensure

optimum accuracy of these units.

Please participate in the preservation of the environment. Return

used batteries to an authorized depot.

PROJECTION OF TIME

Note:

The projection is a red light, not harmful under normal usage, yet care should be taken

to avoid looking directly into the light.

1. When plugged into an AC outlet, the projection alarm can continuously project

the time

2. When operating on batteries alone, the projection alarm will only project when

the SNOOZE button is pressed or the alarm is sounding.

3. The projection will auto-focus for display from about 1.7 to 2.0 meter away. A

dark surrounding will be necessary to clearly see the projection.

The direction of the display can also be rotated 360° in 90° increments by pressing the

Projection Direction

button. The projector case can be rotated 180° to further help

orient the projected display.

TOGGLE BETWEEN THE DISPLAY OF INDOOR TEMPERATURE/

HUMIDITY, PRESET ALARM TIME AND CALENDAR

By pressing shortly the MODE/MIN key, user may toggle between the following displays:

1. Indoor temperature and humidity;

2. Preset alarm time;

3. Day and weekday;

4. Month and day

DCF-77 RADIO CONTROLLED TIME

The time base for the radio controlled time is a Cesium Atomic Clock operated by the

Physikalisch Technische Bundesanstalt Braunschweig which has a time deviation of

less than one second in one million years. The time is coded and transmitted from

Mainflingen near Frankfurt via frequency signal DCF-77 (77.5 kHz) and has a

transmitting range of approximately 1,500 km. Your radio-controlled Projection clock

receives this signal and converts it to show the precise time in summer or wintertime.

The quality of the reception depends greatly on the geographic location. In normal

cases, there should be no reception problems within a 1500km radius of Frankfurt.

Once the outdoor reception test period is completed, the DCF tower icon in the clock

display will start flashing in the upper center. This indicates that the clock has detected

that there is a radio signal present and is trying to receive it. When the time code is

received, the DCF tower becomes permanently lit and the time will be displayed.

If the tower icon flashes, but does not set the time or the DCF tower does not appear at

all, then please take note of the following:

• Recommended distance to any interfering sources like computer monitors or TV

sets is a minimum of 1.5 - 2 meters.

• Within ferro-concrete rooms (basements, superstructures), the received signal is

naturally weakened. In extreme cases, please place the unit close to a window

and/ or point its front or back towards the Frankfurt transmitter.

During nighttime, the atmospheric disturbances are usually less severe and reception is

possible in most cases. A single daily reception is adequate to keep the accuracy

deviation below 1 second.

FUNCTION KEYS

There are three function buttons located on the front of the projection alarm and one on

the top. The function buttons are: AL/HOUR button MODE/MIN button, Projection

direction button, and SNOOZE button.

SNOOZE button

AL / HOUR

button

Projection Direction

button

MODE/ MIN

button

SNOOZE key

• Press to initiate the snooze function when the alarm is sounding.

• Press to activate the projection of time

• Press to confirm the manual setting in the different setting modes

• Press to activate the EL back-light

AL/HOUR key

• Press and hold to advance to the alarm time setting

• Press to set the hour in alarm setting mode

• Press to set the hour in time setting mode

• Press to stop the alarm and snooze

• Press to activate the EL back-light

MODE/MIN key

• Press and hold to advance to the manual setting

• Press to set the minute in alarm setting mode

• Press to set the minute in time setting mode

• Press to set the weekday and year in calendar setting mode

• Press to stop the alarm and snooze

• Press to activate the EL back-light

Projection Direction key

• Press to rotate the time projection image in 90° increments

• Press to activate the EL back-light

MANUAL SETTING

Time zone setting

The time zone default of the Projection clock is “0”. To set a different time zone:

1. Press and hold the MODE/MIN key for about 3 seconds. The current time zone

value at the bottom of the LCD display starts flashing.

flashing

2. Press and release MODE/MIN key to adjust the time zone. The range runs from 0,

1 to 9, then –9, -8 to 0, in consecutive 1-hour intervals.

3. Confirm with the SNOOZE key and enter the Manual time setting.

Manual time setting

In case the Projection clock cannot detect the DCF-signal (for example due to

disturbances, transmitting distance, etc.), the time can be manually set. The clock will

then work as a normal Quartz clock.

Hour flashing

Minutes flashing

1. The hour and the minute digits will start flashing.

2. Use the AL/HOUR key to set the hour; MODE/MIN key to set the minute.

3. Confirm with the SNOOZE key and enter the Calendar setting.

Note:

The unit will still try and receive the signal every hour despite it being manually set.

When it does receive the signal, it will change the manually set time into the received

time.

Calendar setting

The date default of the Projection clock is 1. 1. in the year 2005. Once the radio-

controlled time signals are received, the date is automatically updated. However, if the

signals are not received, the date can also be set manually.

1. The year starts flashing.

flashing

2. Use the MODE/MIN key to set the year (between year 2000-2029).

3. Press the SNOOZE key again to confirm and to enter the month and day setting.

The month and day digits will start flashing.

flashing

4. Use the AL/HOUR key to set the day and MODE/MIN key to set the month.

5. Press the SNOOZE key again to confirm and to enter the Weekday setting mode.

The weekday digit starts flashing.

flashing

6. Use the MODE/MIN key to set the weekday (Mo, Tu, We, Th, Fr, Sa or Su).

7. Confirm all calendar settings with the SNOOZE key and return to the normal

display.

TIME ALARM

Setting the alarm

1. Press and hold “AL/HOUR” button for about three seconds until the alarm time

is flashing.

Alarm-on

icon

flashing

2. Press and release “AL/HOUR” to advance the hour, and “MODE/MIN” to

advance the minute. The time will display in 24-hour format.

3. Press the SNOOZE key to confirm. The alarm is now set and activated.

Activating / Deactivating the alarm

1. After entering the alarm setting mode, the alarm is activated.

2. To toggle between activating and deactivating the alarm, press the “AL/HOUR”

button briefly. Alarm-on icon, “

(((•)))” will be displayed next to the time display

when the alarm is activated.

Turning alarm off (while sounding)

1. While the alarm is sounding, press and release the SNOOZE bar to disable the

alarm for 10 minutes. (After the SNOOZE bar is pressed, the alarm icon will

keep flashing. After 10 min, the alarm will sound again.)

2. To disable the alarm, press and release the AL/HOUR or MODE/MIN button.

EL BACKLIGHT

1. The projection alarm has an EL backlight designed for night-viewing. This will

light up for about 2 seconds whenever the SNOOZE button is pressed.

2. The EL backlight cannot be turned on constantly; this would drain the batteries.

CARE AND MAINTENANCE:

• Extreme temperatures, vibration and shock should be avoided as these may

cause damage to the units and give inaccurate forecasts and readings.

• When cleaning the display and casings, use a soft damp cloth only. Do not use

solvents or scouring agents as they may mark the LCD and casings.

• Do not submerge the units in water.

• Immediately remove all low powered batteries to avoid leakage and damage.

Replace only with new batteries of the recommended type.

• Do not make any repair attempts to the units. Return it to their original point of

purchase for repair by a qualified engineer. Opening and tampering with the units

may invalidate their guarantee.

Page is loading ...

La Crosse Technology RADIO CONTROLLED PROJECTION ALARM CLOCK Owner's manual

Brand: La Crosse Technology

Model: RADIO CONTROLLED PROJECTION ALARM CLOCK

Category: Alarm clocks

Type: Owner's manual

This manual is also suitable for

Download PDF

report

La Crosse Technology RADIO CONTROLLED PROJECTION ALARM CLOCK Owner's manual

This manual is also suitable for

La Crosse Technology RADIO CONTROLLED PROJECTION ALARM CLOCK Owner's manual

Related papers

Other documents