Assembly Instructions
Before commencing assembly, pleass read instruction thoroughly
Beechcraft Bonanza V35/A36
A36ST/A36UP Technical data:
Specification:
Wingspan: 1280mm
Length: 1030mm
Weight: 1384g / 1442g
Configuration
Radio: 6CHanneL 2.4G radio
Motor: 3715 980KV
ESC: 30A / 50A
Battery: 11.1V 2200mA 20C lipo / 14.8V 2200mA 20C lipo
Servo: 9g * 1PCS + 17g * 3PCS / 9g * 2PCS + 17g * 3PCS
Charger: 3S lipo balancer and adapter / 4S lipo balancer
and 3A adapter
Propeller: 1070 3blades
V35ST/V35UP Technical data:
Specification:
Wingspan: 1280mm
Length: 1030mm
Weight: 1384g / 1442g
Configuration
Radio: 6CHanneL 2.4G radio
Motor: 3715 980KV
ESC: 30A / 50A
Battery: 11.1V 2200mA 20C lipo / 14.8V 2200mA 20C lipo
Servo: 9g * 1PCS + 17g * 3PCS / 9g * 2PCS + 17g * 3PCS
Charger: 3S lipo balancer and adapter / 4S lipo balancer
and 3A adapter
Propeller: 1070 3blades
1
Battery and Charging
1. Please do not repair and modify the airplane with non-factory parts. The responsibility is
yours if you do.
2. Please do not mix new and old batteries, or alkaline and rechargable batteries. Use only
fresh alkline batteries, and be sure to install them with the correct polarity.
3. Do not fly the model over roads, railways, near power lines, near airports, or over people
or structures.
1. This RC model is not a toy. The owner / pilot is responsible for any damage to persons or
propety that results from the use of this producer
2. It is very important to follow All instructions for setting up and debugging the model
before attempting to flight
3. The manufacturer and their distributors decline any and all responsibility for any liability
arising from the use of this product
1. Do not charge or use the battery near fire or high temperature, or tinder.
2. Do not leave the battery alone during charging, and remove from charge as soon as the
charge cycle is complete.
3. Keep children away from the battery and charger.
4. Do not disassemble or modify the battery or charger in any way.
5. Do not exhaust the battery cycle, or it will cause the battery permenently damaged.
6. Allow the battery to cool before attempting to recharge it after flying.
7. Do not use any charger except for the factory provided one.
8. Read and follow all instructions...misuse of this Lithium polymer battery or the charger
can result in fire or explosion
Safety Precautions
5
Main wing servos assembly
Assembly the aileron servo and flaps servo to the indication position by glue as picture
Servo protector assembly
Apply glue to the protector then fix it to the appointed place as picture
Clevis assembly
Turn the clevis clockwise into the control rod as picture shown
Main wing control wire assembly
First insert the (z) end of the control wire into the servo arm, then fix the servo arm to the
servo by screw as picture
Motor assembly
Fix the to the motor mount with screw provided as pictures shown
Cowl assembly
Install the cowl into the front of the fuselage as picture show
3X10mm
Screw
X4
X4
X 4
11
Front landing gear assembly
Fix the to the motor mount with screw provided as pictures shown
Steering servo assembly
Apply the glue to the servo interface and fix it to the appointed in front of fuselage, then
control wire as picture shown
Propeller assembly
Fix the propeller adapter to the motor shaft, finally install the propeller spinner as pictures
shown
Main wing assembly
First, put the carbon fibre through the fuselage, then connect the two halves togetger
and fix it to the fuselage with screw provided as pictures shown
X4
X4
12
Canopy decoration assembly
Apply the glue to the canopy and fuselage appointed insterface, then fix the decoration to
as pictures shown
Receiver assembly
Connect all wires into the channels, then apart the mask and fix it as picture shown
Radio power battery assembly
Install the transmitter battery, be sure that the throttle is in the off position. Then turn on
the power and check controls.
13
Battery assembly
Connect the battery to the ESC and fix it into the place appointed, then put the canopy
back to the fuselage as pictures shown
/
