Anova CIRCLEBR Installation guide

Type
Installation guide

This manual is also suitable for

Hammer DrillHammer
Pencil
Wire Brush
Level
Safety Glasses
anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED: HARDWARE NEEDED:
Installation Instructions
Step-by-Step Installation Sequence
!
Tandem Bike Racks, Surface Mount
Product ships fully assembled.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a
3,000 psi minimum and be cured for at least 28 days prior to the installation of the bike rack.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
(6) SS or Rubber Washers
90107A127 OR 90130A050
(6) 3/8”-16 x 1” SS
Button Head Cap Screw
92949A624
(6) 3/8" Drop-in Anchors
97083A310
Allen Wrench Set
7/32"
Masonry Drill Bit Set
1/4" & 1/2"
3/8" Drop-in Anchor
Setting Tool
Unit Weight
Unit Shipping Wt. UPS
(1-2 Units)
Unit Shipping Wt. Truck
(3+ Units)
Unit Ship Size
w/Pallet
Max Units
Per Pallet
Pallet Size/Wt.
(48” X 32”)
Total No.
Pkgs.
Shipping
Class
35 lbs.
38 lbs./unit
38 lbs./unit
10 cu. ft.
8
50 lbs.
1
250
211 North Lindbergh Blvd.
St. Louis, MO 63141
800.231.1327 tel.| 314.754.0835 fax
specify@anovafurnishings.com
anovafurnishings.com
5.50"
Ø 2.38"
7.75"
4.25"
4.00"
Ø .50"
FOOT MOUNT
10.77"
Manufactured in the U.S.
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
Installation Instructions
Step-by-Step Installation Sequence
1.
2.
3.
5.
4.
6.
7.
8.
Evacuate debris from mounting holes using compressed air and a steel wire
brush. This will create a clean environment for the anchor system.
Repeat steps 3 - 6 until all anchors are installed.
!
!
5
42
5
Copyright 2019 ANOV
09/19/2018
Care should be given to avoid rubbing the powder coating o the foot.
A 3/8" rubber washer is a suitable replacement option. Mount the bike rack
to the anchors by fastening a button head cap screw and washer into each
anchor. Leave the hardware nger tight until all of them have been installed.
Verify that the bike rack is level before tightening the anchors. Tighten all of
the hardware with a 7/32" Allen wrench.
Align the mounting holes of the bike rack over top of the anchors.
Use the 3/8" drop-in anchor setting tool and hammer to x the anchor into
the drilled hole by inserting the narrow end of the tool into the anchor and
giving it several hammer blows.
Insert one 3/8" drop-in anchor into the hole and use a hammer to tap the
anchor ush with the concrete.
It is recommended that you start holes in sequential order from the
smaller to the larger drill bits to avoid oversized holes or holes drilled too
deep. Begin with 1/4" diameter drill bit followed by the 1/2" diameter bit.
Place the bike rack in the desired location. Mark the location of the holes with
a pencil. To verify the alignment of the anchor markings you may reference
bottom of page 1.
Tandem Bike Racks, Surface Mount
7
8.1 8.2
  • Page 1 1
  • Page 2 2

Anova CIRCLEBR Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI