Page is loading ...
4. Start up the mCapture and set up the system
Use the DTP menu to confi gure your mCapture device to
the network.
Connect the mCapture to your local KVM.
Press CTRL+ALT+F3 to view the third available terminal.
At the login prompt, type root and press Enter.
At the password prompt, type DTVinabox and press
Enter.
At the # prompt, type stopdtp and press Enter.
At the # prompt, type cd/home/ and press Enter.
At the # prompt, type sh confi guredtp.sh and press
Enter.
Access the mCapture Confi guration
Menu
Attach an extension to the back
of each rail to match the depth of
your rack.
Attach the rails to the rack posts.
Slide the chassis into the rail.
To remove the chassis from
the rack:
Stand in front of the unit and pull
the chassis out as far as it will go.
On the left side, press down on
the plastic retaining mechanism.
On the right side, press up on
the plastic retaining mechanism.
Attach a slide to each side of the
chassis using (5) M4x10mm
screws on each side. Make sure
the plastic retaining mechanism
is located at the back of the
chassis.
f
ront rac
k
posts
rear rac
k
post
s
slide
rail
2. Rack mount the mCapture
• 1 RU chassis (1)
• Power cables (2)
Rack rail kit contains the following:
• Rails (2)
• Slides (2)
• Short extensions (2)
• Nut plates (6)
• Bag of screws
Cable
• VHDCI/RJ 16 Port x 6 feet
1. Verify the contents
NX1011MC INSTALLATION
QUICK START
If the customer orders the
NX-ASI-44 card, place the card in
the PCIe x8 bottom slot.
Keyboard (Purple)
Mouse (Green)
RJ-45 IPMI LAN Port
Serial Port
VGA for Video
Integrated RS-422 Control
Ports
Power Supply (2)
USB (2)
Eth0 (NIC 1)
Eth1 (NIC 2)
Optional NX-GE-4
Optional NX-ASI-44
3. Attach the cables to the back panel
Input 0:0Input 0:1Input 0:2Input 0:3
8. For more information...
Visit support.imaginecommunications.com
for downloads and documentation.
View support and sales contacts at:
www.imaginecommunications.com/
company/contact-us.aspx
Refer to the Nexio® mCapture User Guide,
part number 175-100463-00.
Copyright© 2014 --- Imagine Communications™
Part Number: 175-100358-00
Unlike ASI inputs, where
programs are automatically
enumerated and displayed,
Ethernet inputs must be
discretely set up. Indicate the
input type, session address,
and UDP port.
Manage the input ports and recorders using the jRCS application window. Input ports are shown on the left.
Recorders are to the right of the input port view.
7. Set up mCapture ports in the jRCS
The jRCS application displays in your browser.
Enter your username and password into the
Connection Manager.
Enter the URL for your mCapture Device into your
browser’s address bar. Include the port number 49230.
Example: http://192.168.0.126:49230
You will Need:
- PC with network access to the mCapture
- IP address for your mCapture device
- mCapture username and password
6. Access jRCS to manage the mCapture
To operate the remote KVM over IP you must have a Java Runtime Environment set up on the client PC, then click on the
monitor or choose Remote Control from the menu options.
To access server management, type http://NewlyAssigned-IPaddres. The login credential is ADMIN/ADMIN
dSave any changes and exit from BIOS.
cThe default IP Address is 192.168.000.024 and the
default Subnet Mask is 255.255.255.000. Either use
the defaults or enter a new IP Address and Subnet Mask.
bSelect LAN Confi guration.
aVerify the IPMI Firmware version is 2.23 or higher.
Change the following BIOS settings in Advanced > IPMI Confi guration.
Press DEL to enter system BIOS.
Connect the IPMI port (RJ-45 port next to the Keyboard
and Mouse connectors) to the switch that enabled DHCP.
5. Set up server management via IPMI
/
