Sceptre X 7G Naga V X7g-NagaV X7g-NagaV User manual

X7G-NagaV

User’s Manual

i

FCC Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

FCC WARNING

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may

cause harmful inerference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Caution:

To comply with the limits for an FCC Class B computing device, always

use the shielded signal cord supplied with this unit.

ii

The Federal Communications Commission warns that changes or

modifications of the unit not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

CE mark for Class B ITE (Following European standard EN55022/1998; EN61000-

3-2/1995; EN61000-3-3/1995, EN55024/1998, EN60950/1992+A1+A2+A3+A4+A11)

Radio Frequency Interference Statement

Warning:

This is a Class B product. In a domestic environment, this product may

cause radio interference in which case the user may be required to take

adequate measures.

Canadian Doc Notice

For Class B Computing Devices

This digital apparatus does not exceed the Class B limits for radio noise

emissions from digital apparatus as set out in the Radio Interference

Regulation of the Canadian Department of Communications.

“Le présent appareil numérique n’èmet pas de bruits radioélectriques

dépassant les limites applicables aux appareils numériques de la class B

prescrites dans le Règlement sur le brouillage radioélectrique édicté par

le ministère des Communications du Canada."

iii

TABLE OF CONTENTS

TABLE OF CONTENTS ..........................................................................................III

Your New LCD Monitor 1

Unpacking 1

Identifying Components 3

Adjusting the Tilting Angle 5

Connecting AC Power and Video Cable 6

Power Management System 6

The LCD Monitor’s Control Panel 7

Adjusting the Monitor’s Display 8

TFT LCD Monitor Specifications 14

Supported Timing 16

Troubleshooting 17

1 Rev.1

The LCD Monitor

Your New LCD Monitor

Your LCD Monitor has been designed to be versatile, ergonomic and

user-friendly. The LCD Monitor is capable of displaying most

standards, from 640x400 VGA to 1280x1024 SXGA. The digital

controls located on the front panel allow the user to easily adjust the

Monitor’s display parameters, and the LCD Monitor’s small footprint

gives you more room in your workspace for other peripherals.

Lightweight and compact, the LCD Monitor is the perfect solution for

users on the go. You can use the LCD Monitor for everything from

making business presentations to playing computer games.

The architecture of the LCD Monitor incorporates an LCD panel that produces a clear display

with low radiation emission. And with its low power consumption, the LCD Monitor helps you

reduce your power bill.

Unpacking

Before unpacking your LCD Monitor, prepare a suitable workspace for

your LCD Monitor and computer. Look for a stable, level and clean

surface near a wall outlet. Even though the LCD Monitor uses very

little power, you should put it in a location which allows sufficient

airflow to ensure that the LCD Monitor and your computer do not

overheat. Set up your LCD Monitor so that the panel is not facing a

window where sunlight often comes in. The glare caused by sunlight

reflecting off of the LCD Monitor’s screen will make it difficult to use the

Monitor for viewing.

Note: Using a computer for an extended period of time with a poor workstation

set-up and incorrect working habits can cause health problems. The science of

ergonomics studies the relationship between health and a suitable working

environment. There is a section on ergonomics at the end of this chapter. For

more information on ergonomics, contact your nearest computer bookstore, or

local library. The Internet also has information on this and other subjects.

2 Rev.1

After unpacking your LCD monitor, make sure the following items are included

in the box and are in good condition:

• LCD monitor

• Power Cord

• Monitor-To-PC Analog signal cable 15pin

• User’s manual

If you find that any item to be missing or appear to be damaged,

contact your dealer immediately. Do not throw away the packing

material or shipping carton in case you need to ship or store the LCD

monitor in the future.

3 Rev.1

Identifying Components

A. The LCD Monitor — Front View

Figure 1-1: The LCD Monitor Front View

1. Power-On Indicator

This Circular LED indicator green lit when the power is on and

orange lit when the LCD monitor is in power-saving mode.

2. Monitor Stand

3. LCD Screen

The LCD monitor screen is a 17-inch TFT 1280 x 1024 screen.

4. LCD Monitor Control Panel

Refer to Chapter 2 for more details.

3

2

1

4

4 Rev.1

B. "Hot Keys" for Quick Adjustment of Monitor Settings

Figure 1-2: "Hot Keys"

1. Brightness Adjustment "hot key":

Press this + button to allow you to

adjust the brightness of the LCD

Monitor directly

Brightness

50

2. Contrast Adjustment “ Hot key”

Press this - button to allow you to

adjust the contrast of the LCD Monitor

directly

Contrast

50

3. Auto adjustment “ Hot Key “

Press this to allow you to do the

auto adjustment to get the optimized

view

( For VGA port only, DVI port can’t

adjustment )

Auto

P



+

5 Rev.1

Adjusting the Tilting Angle

The LCD Monitor’s angle settings range from 0° to 10°.

10

Figure 1-3: Tilting the Monitor

0 to 10

6 Rev.1

Connecting AC Power and Video Cable

Note: Turn off your PC and the LCD monitor before connecting your LCD monitor to the

computer.

Figure 1-4: The AC Adapter

Power Management System

This LCD Monitor complies with the VESA DPMS power management proposal.

When the LCD Monitor is in power-saving mode or detects an incorrect timing, the monitor

screen will be blank and the power LED indicator from green lit change to orange lit.

VGA

AC-IN

AC Outlet

(Wall Socket)

Computer

Power Cord

Monitor

Power Cord

7 Rev.1

The Display Controls

The LCD Monitor’s Control Panel

Figure 2-1: The Control Panel

1. : Enable the OSD Menu button or

/ Move the cursor to the left ( when OSD is enabled)

2. : Move the cursor to the Right ( When OSD is enabled)

/ Auto-adjustment hot key

3. - : Enter into the sub-menu or decrease the value

/ Contrast hot key

4. + : Enter into the sub-menu or increase the value

/ Brightenss hot key

5. :Power Switch

This button lets you turn power for the LCD monitor ON or

OFF.

P



+

8 Rev.1

Adjusting the Monitor’s Display

OSD Main Menu

1. Pressing the Y button causes the screen below to appear.

2. Use the Y &Z key to select the desired group, then press – or +

key to enter into sub-menu

3. Repeat step 2 to select the changed item, then – or + to change

the value.

Monitor Control

OSD Main SCREEN

Main Menu

Sub Menu

Description

9 Rev.1

Monitro Adjustment

Allow you to adjust the LCD monitor’s display settings. Press the

Adjustment control button to display the submenu. Use the Function

Select button to select one of the following submenu options:

Auto Adjustment (For VGA port only, DVI port can’t adjustment)

Press the Adjustment control button to let the monitor determine

and select the setting that is most appropriate for your system

requirements.

H-POSITION: (For VGA port only, DVI port can’t adjustment)

To move the LCD monitor's display left or right on a horizontal plane.

V- POSITION: (For VGA port only, DVI port can’t adjustment)

To move the LCD monitor's display up or down on a vertical plane.

PHASE: (For VGA port only, DVI port can’t adjustment)

To adjust the focus and clarity of the display

CLOCK: (For VGA port only, DVI port can’t adjustment)

To adjust the display pixel alignmen

t.

RESET:

To reset all of the Monitor-Control submenu settings to

the factory default.

GRAPHIC/TEXT:

Press the adjustment control button to switch between text

and graphic display modes.

EXIT:

10 Rev.1

To exits the Monitor-Control submenu

OSD-control

The OSD-Control menu lets you adjust the position of the OSD on the screen. Press the

Adjustment control button to display the submenu.

OSD-H-POSITION:

To change the position of the OSD on a horizontal plane.

OSD-V-POSITION:

To change the position of the OSD on a vertical plane.

OSD-TIMER:

The OSD menu display time can be set at 5, 10, 15,

20, 25 or 30 seconds.

EXIT:

To exit the OSD-Control submen

u.

GRAPHIC-CONTROL:

The Graphic-Control option lets you make adjustments that effect the contrast,brightness and

color of the LCD monitor’s display.

CONTRAST:

To adjust the contrast level of the display screen

BRIGHTNESS:

To adjust the light level on the display screen.

11 Rev.1

COLOR:

To select the LCD monitor’s color display. The available options are cold, warm and User.

Selecting the user option lets you make individual adjustments to the R, G and B items.

COLOR R, G and B ADJUST:

To make individual adjustments to the Red, Blue, Green

(RGB) gain for the color temperature.

AUTO LEVEL: To adjust automatically the white balance

display.

RESET:

To reset all of the Graphic-Control submenu settings to

the factory default.

EXIT: To exit the Graphic-Control submenu.

MISC-CONTROL:

The Misc-Control menu option lets you select the OSD display

language and view system information.

LANGUAGE:

The supported languages include German, English, French, Spanish, Italian.

INFORMATION:

12 Rev.1

To indicate display mode timings and firmware version.

EXIT: To exit the Misc-Control submenu.

EXIT:

Use the OSD Exit item to close the OSD menu. The OSD will disappear by itself if left inactive.

13 Rev.1

Note:

1) No video

When the monitor is ON and there is no video signal received, the following message will be

displayed

2) Signal out of range

When the frequency range of the signal is out of the Monitor’s specifications, (over 85HZ) the

display will show the following message

Over Range

No Video

14 Rev.1

Appendix A

TFT LCD Monitor Specifications

LCD Panel 17" SXGA

Control

Functions

Power

Software Power switch with LED indicator

(ON/OFF)

Main Menu Submenu

MONITOR-

CONTROL

Auto Adjustment, H-POSITION,

V- POSITION, PHASE, CLOCK,

GRAPHIC/TEXT, RESET, EXIT

OSD-CONTROL OSD-H-POSITION, OSD-V-

POSITION, OSD-TIMER, EXIT

MISC-CONTROL LANGUAGE, INFORMATION, EXIT

GRAPHIC-

CONTROL

CONTRAST, BRIGHTNESS, COLOR,

COLOR R, G and B ADJUST, AUTO

LEVEL, RESET, EXIT

On-Screen

Display

(OSD)

EXIT

Display Area

(mm)

337.92 x 270.336

(17" diagonal)

Display

Colors

16.7 M

Video

Interface

VGA Compatible Analog RGB

15 Rev.1

Scanning Frequency

H/V, Hz

24-80K

50-75

Power Management Meets VESA DPMS

Power Consumption

(ON/OFF, W)

35W/1W Max.

Dimensions

WxHxD

14.74 x 15.10 x 6.81 in.

(374.5 x 383.45 x 173mm)

Net Weight

(approx.)

9.46 lbs

(4.3 Kg)

Power Supply Universal Input AC Socket

Environment Operating Temperature: 32 to 104°F (0 to 40° C)

Relative Humidity: 10% to 90%

Regulatory

FCC B DoC,UL/cUL,Energy star

16 Rev.1

Appendix B

Supported Timing

Item

Standards

Resolution

Dot Clock

(MHz)

Vertical

Scanning

Frequency

(Hz)

Horizontal

Scanning

Frequency

(kHz)

1 NEC PC98 640x400 21.05 56.42 24.83

2 MAC 13" mode 640x480 30.24 66.67 35.00

3 MAC 16" mode 832x624 57.28 74.55 49.73

4 MAC 17" mode 1024x768 80.00 75.02 60.24

5 VGA 640x350 25.18 70.09 31.47

6 VGA 640x400 25.18 70.09 31.47

7 VGA 640x480 25.18 59.94 31.47

8 VESA 640x480 31.50 72.81 37.86

9 VESA 640x480 31.50 75.00 37.50

10 VESA 800x600 36.00 56.25 35.16

11 SVGA 800x600 40.00 60.32 37.88

12 VESA 800x600 50.00 72.19 48.08

13 VESA 800x600 49.50 75.00 46.88

14 VGA 720x400 28.32 70.09 31.47

15 XGA 1024x768 65.00 60.00 48.36

16 VESA 1024x768 75.00 70.07 56.48

17 VESA 1024x768 78.75 75.03 60.02

18 VESA 1280X1024 108 60 63.98

19 VESA 1280X1024 135 75 80

*Once a mode is optimized, there is no need to make any further adjustment

as long as the VGA card remains unchanged.

*Specifications are subject to change without notice.

Page is loading ...

Sceptre X 7G Naga V X7g-NagaV X7g-NagaV User manual

This manual is also suitable for

Sceptre X 7G Naga V X7g-NagaV X7g-NagaV User manual

Related papers

Other documents