La Crosse Online Temperature and Humidity Wireless Alert Sensor User manual

Online Temperature and Humidity Wireless Alert Sensor
La Crosse
Brand
La Crosse
Model
Online Temperature and Humidity Wireless Alert Sensor
Category
Weather stations
Type
User manual

This manual is also suitable for

TX60U-IT
Wireless 915 MHz
Temperature and Humidity Sensor
www.weatherdirect.com
TX60U-IT sensor measures:
(A) Ambient air temperature and humidity (Channel 1)
(B) Probe temperature (Channel 2): Use the included 6 Ft. detachable,
waterproof temperature probe to measure water, soil, or even the conditions
inside of a refrigerator or aquarium.
The TX60U-IT sensor sends the collected outdoor temperature and humidity
measurements to your existing Weather Direct® Gateway (not included) with a
wireless range over 200 Ft. (60.96 m). The Weather Direct® Gateway uses your
high-speed internet connection to upload the temperature and humidity
measurement log to your included www.weatherdirect.com account. Login to
your account and view your temperature and humidity measurement log
anywhere in the world with an Internet connection.
SUGGESTED USES
Note: The base unit cannot get wet, and may be affected by high humidity
conditions. Use the detachable probe for wet or high humidity environments.
• Humidity monitoring:
o Pianos
o Greenhouses
o Reptile terrariums
o Cigar storage/humidors
o Allergies (prevent dust mites & mold)
o Laundry rooms and basements at
rental properties or vacation homes
• Storage conditions (temperature and humidity):
o R.V. storage
o Warehouses
o Long-term storage
o Laboratories
o Medicine/pharmaceuticals
o Cosmetics
• Temperature monitoring using detachable probe:
o Pools, spas hot tubs
o Aquariums, terrariums and other pet care
o Bird baths
o Refrigerators, freezers, laundry rooms and
basements at rental properties or vacation homes
o Food service
o Computers/ server rooms
o Home beer brewing
o Soil temperature using probe:
o Farms
o Gardens
o Greenhouses
PACKAGE LIST OF CONTENTS
1. One TX60U-IT wireless temperature & humidity sensor
2. Mounting hardware
3. Instruction manual
ADDITIONAL EQUIPMENT (NOT INCLUDED)
• Two fresh AAA, IEC LR03, 1.5V Alkaline batteries
• A Weather Direct® Gateway
• PC with high speed internet to configure the TX60U-IT sensor
IMPORTANT SETUP & OPERATION NOTES
• The TX60U-IT sensor should be placed in a dry, shaded area. Please
avoid a location with direct sun, as that will cause incorrect readings.
• Fog and mist will not harm the TX60U-IT sensor but direct rain must be
avoided. Note: Exposing the TX60U-IT sensor case to extreme humidity
may temporarily disrupt data. The sensor case reads humidity, but should
not be ‘submerged’ in water. The included 6 ft. probe can be used for
measuring water temperature.
• The TX60U-IT sensor has a wireless range of 200 feet (60.96 m). Keep
in mind that the 200 ft range equates to open air with no obstructions, and
that radio waves DO NOT curve around objects. Actual transmission
range will vary depending on what is in the path of the signal. Each
obstruction (roof, walls, floors, ceilings, thick trees, etc.) will effectively cut
signal range in half.
Example: If the TX60U-IT Sensor, with a 200 feet (60.96 m) range, is
mounted on an exterior wall, the signal must then pass through one
exterior wall, one interior wall, and across the 10 feet (3 m) width of the
room between the 2 walls to reach the Weather Direct® Gateway. The
first wall will reduce the range to 100 feet (30.48 m), and the second wall
will reduce the range to 50 feet (15.24 m). Factoring in the 10 foot room,
this leaves a maximum of 40 feet (12.2 m) of remaining signal range.
This allowance is typically enough for a frame wall with non-metallic
siding; however certain materials can reduce range even further. Metal
siding, stucco, and some types of glass can reduce signal range by as
much as ¾ or more, compared to the ½ reduction typical of most
obstructions. It is possible to receive a signal through these materials,
however maximum range will be much less due to their tendency to
absorb or reflect a much larger portion of the sensor’s signal.
• The TX60U-IT sensor measures and updates the temperature and
humidity on the LCD every 6 seconds. Note: The new measurement is
reported to the computer at intervals that you select
using your online
account. Your online account will be updated with the new measurements
based on the time interval that you select.
(A)
BEGIN SET UP
First you must have a Weather Direct® Gateway registered so that it can
communicate with your new TX60U-IT sensor. If you do not already have a
Gateway registered, begin by registering your Weather Direct® Gateway online
at: www.weatherdirect.com
After successful online Weather Direct® Gateway registration, you will use to
following steps to "connect" both devices:
Step 1. Please make sure the TX60U-IT sensor is 3 to 10 feet away from the
Gateway during the registration process. Registration may fail if the
device is too close or too far from the Gateway.
Step 2. Install batteries into the TX60U-IT sensor. (See “Battery Installation”)
Step 3. Press and release the button on the TX60U-IT Sensor.
Step 4. Press and release the button on the Weather Direct® Gateway.
Step 5. Wait approximately 10 seconds for the two devices to make a
connection. The LED on the TX60U-IT sensor will turn ON to signal
that it is trying to connect to the Gateway.
Step 6. The LED on the TX60U-IT Wireless sensor will turn OFF once the
device is successfully connected to the Gateway.
Step 7. The channel number for connection will briefly display on the TX60U-IT
LCD and the LED will light up for approximately 5 seconds. Then, the
LCD will alternate the measurement values for channel 1 and 2:
o CHANNEL 1: Measurement received by the internal
temperature and humidity sensor within the sensor body.
o CHANNEL 2: Measurement received by the optional
external temperature probe. "nC" will be displayed if no
probe is attached.
Note: If registration fails, the LCD on the TX60U-IT will display “1” and LED will
continue to blink in sets of three. If this happens, please return to Step 3 to
restart the setup process.
OPTIONAL CHANNEL 2 TEMPERATURE PROBE
If the optional probe for the TX60U-IT sensor is unplugged, the LCD on the
TX60U-IT sensor will display "nC" for the CHANNEL 2 reading. The probe can
be plugged into the TX60U-IT sensor at anytime without resetting the units.
ONLINE ACCOUNT SETUP
1 YEAR OF E-MAIL / TEXT MESSAGE ALERTS IS INCLUDED WITH INITIAL
SENSOR ACTIVATION ON WWW.WEATHERDIRECT.COM:
Once the TX60U-IT sensor is set up on your www.weatherdirect.com account,
you may choose to activate the optional e-mail / text message alerts:
(1) If temperature or humidity exceed your defined range
(2) If connection is lost
(3) If batteries are low
TX60U-IT ONLINE REGISTRATION / CONFIGRUATION
Please log in to your account on www.weatherdirect.com and follow the online
instructions to register and configure the TX60U-IT sensor so that you may
begin collecting measurement logs. You may select your desired transmission
period (2, 5, 10, 20 minutes). When e-mail / text alerts are active on your
account, settings for temperature and humidity alerts are available
Note: To delete or reset the TX60U-IT sensor from your account, press and
hold the button on the sensor until the LCD displays a full segment and then
delete the record in your Weather Direct® account. WARNING: If you do this,
you will have to re-register your device.
AUTOMATIC SPREADSHEET CREATION OF MEASUREMENT LOG
Once the TX60U-IT sensor is set up on your www.weatherdirect.com account
and is building a measurement log, you can download the data to your
computer in the form of a spreadsheet. You have the option to either: "save the
file to your hard drive" or "open it directly from the website". You must have an
application on your computer that supports Microsoft® Excel formatted files for
this option to work. No subscription required. Please refer to
www.weatherdirect.com for more information.
(B)
Optional
external probe
LCD
This socket is ONLY
for the external probe.
DO NOT insert
power plug into it.
Button
WARRANTY INFORMATION BATTERY INSTALLATION
1. Remove the battery cover by sliding the cover down. La Crosse Technology, Ltd provides a 1-year limited warranty on this product
against manufacturing defects in materials and workmanship. 2. Observing the correct polarity install 2 AAA, Alkaline batteries. The
batteries will fit tightly (to avoid start-up problems make sure they do not
spring free).
This limited warranty begins on the original date of purchase, is valid only on
products purchased and used in North America and only to the original
purchaser of this product. To receive warranty service, the purchaser must
contact La Crosse Technology, Ltd for problem determination and service
procedures. Warranty service can only be performed by a La Crosse
Technology, Ltd authorized service center. The original dated bill of sale must
be presented upon request as proof of purchase to La Crosse Technology, Ltd
or La Crosse Technology, Ltd’s authorized service center.
3. Replace the battery cover by sliding upwards. Be sure battery cover is on
securely.
LOW BATTERY INDICATOR
When batteries are low, the low battery indicator show up on the LCD. You will
receive an e-mail or cellular notification (if notifications have been configured)
when the battery power of the TX60U-IT sensor is low. Change the batteries
immediately.
La Crosse Technology, Ltd will repair or replace this product, at our option and
at no charge as stipulated herein, with new or reconditioned parts or products if
found to be defective during the limited warranty period specified above. All
replaced parts and products become the property of La Crosse Technology, Ltd
and must be returned to La Crosse Technology, Ltd. Replacement parts and
products assume the remaining original warranty, or ninety (90) days,
whichever is longer. La Crosse Technology, Ltd will pay all expenses for labor
and materials for all repairs covered by this warranty. If necessary repairs are
not covered by this warranty, or if a product is examined which is not in need or
repair, you will be charged for the repairs or examination. The owner must pay
any shipping charges incurred in getting your La Crosse Technology, Ltd
product to a La Crosse Technology, Ltd authorized service center. La Crosse
Technology, Ltd will pay ground return shipping charges to the owner of the
product to a USA address only.
Note: The LED turns ON briefly after changing batteries. However, the LED
turns OFF if there is no Weather Direct® Gateway connected. The previously
stored information in the TX60U-IT sensor will not be affected or cancelled
while you change the batteries.
MOUNTING
THE TX60U-IT TEMPERATURE & HUMIDITY SENSOR
The TX60U-IT sensor can be mounted onto a wall with the use of screws
MOUNTING WITH SCREWS
Your La Crosse Technology, Ltd warranty covers all defects in material and
workmanship with the following specified exceptions: (1) damage caused by
accident, unreasonable use or neglect (including the lack of reasonable and
necessary maintenance); (2) damage occurring during shipment (claims must
be presented to the carrier); (3) damage to, or deterioration of, any accessory or
decorative surface; (4) damage resulting from failure to follow instructions
contained in your owner’s manual; (5) damage resulting from the performance
of repairs or alterations by someone other than an authorized La Crosse
Technology, Ltd authorized service center; (6) units used for other than home
use (7) applications and uses that this product was not intended or (8) the
products inability to receive a signal due to any source of interference.. This
warranty covers only actual defects within the product itself, and does not cover
the cost of installation or removal from a fixed installation, normal set-up or
adjustments, claims based on misrepresentation by the seller or performance
variations resulting from installation-related circumstances.
1. Remove the mounting bracket from the TX60U-IT sensor.
2. Place the mounting bracket over the desired location.
3. Mark the mounting surface with a pencil through the two screw holes of
the bracket,.
4. Screw the mounting bracket onto the mounting surface. Ensure that the
screws are tight against the bracket.
5. Insert the TX60U-IT sensor into the bracket.
LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR
INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR
DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF
THIS PRODUCT. THIS PRODUCT IS NOT TO BE USED FOR MEDICAL
PURPOSES OR FOR PUBLIC INFORMATION. THIS PRODUCT IS NOT A
TOY. KEEP OUT OF CHILDREN’S REACH.
TABLE STANDING AND OTHER MOUNTING OPTIONS
With the mounting bracket installed at the bottom
or on the top of the TX60U-IT sensor, the user can
place it on any flat surface.
Note:
Before permanently fixing the TX60U-IT sensor wall base, place all
units in the desired locations to check that the outdoor temperature
& humidity readings are receivable. In event that the signal is not
received, relocate the TX60U-IT sensor or move them slightly as
this may help the signal receptio
This warranty gives you specific legal rights. You may also have other rights
specific to your State. Some States do no allow the exclusion of consequential
or incidental damages therefore the above exclusion of limitation may not apply
to you.
n.
For warranty work, technical support, or information, please contact:
MAINTENANCE AND CARE
La Crosse Technology, Ltd
• Extreme temperatures, vibration, and shock should be avoided to prevent
damage to the units.
2809 Losey Blvd. S.
La Crosse, WI 54601
• Clean displays and units with a soft, damp cloth. Do not use solvents or
scouring agents; they may mark the displays and casings.
Phone: 608.782.1610
Fax: 608.796.1020
• Do not submerge the sensor case in water.
• Avoid kinking the temperature probe cable.
For online contact / support / e-mail:
• Immediately remove all low powered batteries to avoid leakage and damage.
www.lacrossetechnology.com/support
• Opening the casings invalidates the warranty. Do not try to repair the unit.
Contact La Crosse Technology® for repairs.
For information on other products:
[email protected]
SPECIFICATIONS
For online setup and registration:
www.weatherdirect.com
Data measuring range:
The device sensor:
Temperature range: -40 °F to 140°F with 0.2°F resolution
“OFL” displayed if outside this range.
Humidity measuring range: 3% to 99%
Transmission range: 200 feet (60.96 m) in open space
The probe sensor:
Temperature range: -40 °F to 140°F with 0.2°F resolution
“OFL” displayed if outside this range, and
displayed “nC” if no connection.
Power Supply:
Temperature transmitter : 2 x AAA, IEC LR03, 1.5V
Battery life cycle: Approximately 24 months
Recommended battery type: Alkaline
Dimensions (H x W x D):
5.23" x 0.76" x 1.44"
For online product information:
www.weatherdirect.com/tx60
FCC DISCLAIMER
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
All rights reserved. This handbook must not be reproduced in any form, even in
excerpts, or duplicated or processed using electronic, mechanical or chemical
procedures without written permission of the publisher.
This handbook may contain mistakes and printing errors. The information in
this handbook is regularly checked and corrections made in the next issue. We
accept no liability for technical mistakes or printing errors, or their
consequences.
All trademarks and patents are acknowledged.
  • Page 1 1
  • Page 2 2

La Crosse Online Temperature and Humidity Wireless Alert Sensor User manual

Online Temperature and Humidity Wireless Alert Sensor
La Crosse
Brand
La Crosse
Model
Online Temperature and Humidity Wireless Alert Sensor
Category
Weather stations
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents