La Crosse 925-1418 Installation guide

La Crosse
Brand
La Crosse
Model
925-1418
Type
Installation guide

La Crosse Technology 925-1418 is a Sensor Weather Shield designed to protect your outdoor sensors from rain and snow. It offers limited protection from the sun's heat and is compatible with temperature sensors, temperature/humidity sensors, and probe sensors.

The shield features holes for mounting screws and slots for zip ties, allowing for flexible and secure installation on flat surfaces, walls, or posts. It comes with a mounting bracket for easy attachment to a shaded location.

The shield's dimensions are 7.00” H x 3.73” W x 3.98” D (177.8 x 94.74 x 101.9 mm), providing ample space for most outdoor sensors. It is designed to keep the sensor securely in place and protect it from the elements, ensuring accurate and reliable readings.

La Crosse Technology 925-1418 is a Sensor Weather Shield designed to protect your outdoor sensors from rain and snow. It offers limited protection from the sun's heat and is compatible with temperature sensors, temperature/humidity sensors, and probe sensors.

The shield features holes for mounting screws and slots for zip ties, allowing for flexible and secure installation on flat surfaces, walls, or posts. It comes with a mounting bracket for easy attachment to a shaded location.

The shield's dimensions are 7.00” H x 3.73” W x 3.98” D (177.8 x 94.74 x 101.9 mm), providing ample space for most outdoor sensors. It is designed to keep the sensor securely in place and protect it from the elements, ensuring accurate and reliable readings.

Sensor Weather Shield
Model: 925-1418
DC: 021318
The Sensor Weather Shield is designed to protect your outdoor sensors from rain and snow.
This shield will oer limited protection from the sun’s heat.
• Temperature sensor
• Temperature/Humidity sensor
• Probe sensor
• Twist the cover clockwise to remove the base.
• Attach the Velcro tape to the sensor and to the upright on the base. This keeps the sensor from tipping.
• Alternately, secure the sensor with a zip tie.
• With a probe sensor, be sure the probe wire fits through the round hole in the base.
• Place cover over sensor and base. Twist counter clockwise to lock into place. Sensor must fit entirely in
the sensor shield to be protected.
• Mount the sensor shield so that the sensor is in range of the display.
Slots for zip ties
Holes for mounting screws
Holes for mounting screws
Sensor
Velcro Tape
Upright
Base
If you have a sensor with a
probe wire, there is a hole for
the probe to exit.
Note: Sensor and probe are
not included
INSERT SENSOR (not included)
MOUNT SENSOR SHIELD
Mount to a flat surface:
• Twist the cover clockwise to remove the base.
• Place one long screw through the center hole of the base.
• Tighten until the head of the screw is flat with the base. Do not over tighten.
Mount to a wall or post:
• Slide the mounting bracket down and remove from the cover.
• Take note of the UP ARROW on the back of the bracket.
• Find a shaded location and attach the bracket (arrow UP) with the four screws (included), or with the two zip ties (included).
Note: Allow room to slide cover onto bracket.
• Slide the shield down onto the bracket.
DIMENSIONS: 7.00” H x 3.73” W x 3.98” D (177.8 x 94.74 x 101.9 mm)
WARRANTY & SUPPORT
La Crosse Technology, Ltd. provides a 1-year limited time warranty (from date of purchase) on this product relating to
manufacturing defects in materials & workmanship.
For Full Warranty Details and online support, Visit: www.lacrossetechnology.com/support
For warranty work, technical support or other information contact out friendly support staff:
La Crosse Technology, Ltd
2830 South 26th St
La Crosse, WI 54601
Contact Support: 1-608-782-1610
  • Page 1 1
  • Page 2 2

La Crosse 925-1418 Installation guide

La Crosse
Brand
La Crosse
Model
925-1418
Type
Installation guide

La Crosse Technology 925-1418 is a Sensor Weather Shield designed to protect your outdoor sensors from rain and snow. It offers limited protection from the sun's heat and is compatible with temperature sensors, temperature/humidity sensors, and probe sensors.

The shield features holes for mounting screws and slots for zip ties, allowing for flexible and secure installation on flat surfaces, walls, or posts. It comes with a mounting bracket for easy attachment to a shaded location.

The shield's dimensions are 7.00” H x 3.73” W x 3.98” D (177.8 x 94.74 x 101.9 mm), providing ample space for most outdoor sensors. It is designed to keep the sensor securely in place and protect it from the elements, ensuring accurate and reliable readings.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents