724-746-5500 | blackbox.com724-746-5500 | blackbox.com 724-746-5500 | blackbox.com
Page 5 Page 6
© Copyright 2012. Black Box Corporation. All rights reserved.
Black Box and the Double Diamond logo are registered trademarks of
BB Technologies, Inc. Any other trademarks mentioned in this manual
are acknowledged to be the property of the trademark owners.
BLACK BOX
®
Quick Start Guide
Isolated and non-isolated models available.
Industrial Grade 4-Port USB Hub
ICI200A
ICI202A
Black Box Tech
Support: FREE! Live.
24 / 7. Tech support
the way it should be.
Great tech support is just 30 seconds
away at 724-746-5500 or blackbox.com.
Order toll-free in the U.S.:
Call 877-877-BBOX
(outside U.S. call 1-724-746-5500)
FREE technical support
24 hours a day, 7 days a week:
Call 724-746-5500 or
fax 724-746-0746
Mailing address:
Black Box Corporation
1000 Park Drive
Lawrence, PA 15055-1018
Web site: www.blackbox.com
E-mail: info@blackbox.com
Customer
Support
Information
BLACK BOX
®
Industrial Grade 4-Port USB Hub
Table 1. LED indicators.
LED Type State Description
*USB Power
ON
The hub is running on USB power.
External power is not applied. The hub
can supply up to 100 mA power per
downstream port.
OFF
The hub is either using external power,
or no power is present.
External Power
ON
External power is applied and an active
host connection exists. The hub will
provide 500 mA per downstream port.
OFF
The hub is bus powered (ICI200A only)
or no power is present (ICI202A).
Port LEDs 1–4
ON Port is active and ready for use.
OFF
Port has a fault. Power may need to be
cycled.
*USB Power LED is on ICI200A model only.
Troubleshooting
Problem: The hub is installed, but a downstream
device isn’t working.
Soluton: Some USB devices get their power from the
USB cable. If you are using the ICI200A without an
external power supply, it will only provide 100 mA to
the downstream ports. If your devices need more
power, connect an external power supply to the
ICI200A. It will then provide 500 mA to the down-
stream ports.
Problem: Do I need drivers for the hub?
Solution: No, the operating system will detect it and
install it automatically.
Problem: How can I be sure it has been installed?
Solution: The new hub will be listed in the Device
Manager.
Troubleshooting (Continued from page 5)
Problem: Can I use USB 1.1 and USB 2.0 devices
together?
Solution: Yes. USB 2.0 is backwards-compatible with
USB 1.0 and 1.1.
SUITABLE FOR USE IN CLASS I, DIVISION 2,
GROUPS A, B, C AND D HAZARDOUS
LOCATIONS, OR NONHAZARDOUS LOCATIONS
ONLY.
WARNING - EXPLOSION HAZARD -
SUBSTITUTION OF ANY COMPONENT MAY
IMPAIR SUITABILITY FOR CLASS I, DIVISION 2.
WARNING - EXPLOSION HAZARD - DO NOT
DISCONNECT EQUIPMENT WHILE THE CIRCUIT IS
LIVE OR UNLESS THE AREA IS KNOW TO BE FREE
OF IGNITABLE CONCENTRATIONS.
INSTALL IN ACCORDANCE WITH CONTROL
DRAWING NUMBER 260-10135-00
724-746-5500 | blackbox.com724-746-5500 | blackbox.com 724-746-5500 | blackbox.com
Industrial Grade 4-Port USB Hub Industrial Grade 4-Port USB HubIndustrial Grade 4-Port USB Hub
Page 3Page 2 Page 4
What’s Included
Your package should include the following items. If
anything is missing or damaged, contact Black Box
Technical Support at 724-746-5500 or
info@blackbox.com.
• (1) Industrial Grade 4-Port USB Hub
• (1) USB cable
• (2) panel-mount adapters and (4) mounting screws
• (1) DIN rail adapter and (3) mounting screws
• This quick start guide
NOTE: A power supply is not included.
Overview
Figure 1 shows the front view of the hub. Figure 2
shows the side view.
To USB host
LED
indicators
Downstream
ports
Figure 1. Front view.
Detachable
terminal block
Power plug
Figure 2. Side view
Installation Steps
Step 1: Mounting
DIN rail mounting: Attach the DIN rail bracket with
the flat surface of the bracket facing the back of the
hub, as shown in Figure 3.
DIN rail
bracket
Figure 3. DIN rail bracket attached to hub.
Panel mounting: Attach the panel-mount brackets to
either side of the hub. They can be attached in (4)
positions: up, down, forward, and back.
Panel-mount
brackets
Figure 4. Panel-mount bracket positions.
Step 2: Connect the Power Supply
ICI200A: The non-isolated Industrial Grade 4-Port USB
Hub (ICI200A) can operate without an external power
supply. When the hub is running on USB power,
it provides a maximum of 100 mA to each of the
downstream ports.
ICI202A: Unike the non-isolated hub, the isolated
Industrial Grade 4-Port USB Hub (ICI202A) will not
operate without an external power supply. You can
use the detachable terminal block input or the locking
barrel jack. The terminal block is polarity protected.
When powered, the ICI200A and ICI202A will provide
500 mA to each downstream port. They require 10
to 30 VDC of external power and will consume a
maximum of 16 W.
NOTE: The ICI202A adds 4-kV isolation.
Step 3: Grounding
We recommend that you ground the chassis. Connect
a grounding wire from the green ground lug to a
good source of earth ground.
Figure 5. Grounding the chassis.
Step 4: LED Status
Figure 6 shows the LEDs on the ICI200A and ICI202A.
Table 1 describes their functions.
Figure 6. Left: ICI200A; right: ICI202A.
-
1
-
2
Black Box Industrial Grade 4-Port USB Hub User manual
- Category
- Dehumidifiers
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Black Box IC640A User manual
-
-
-
Black Box IC401A User manual
-
-
-
Black Box IC400A User manual
-
-
Black Box ServSwitch ACS253A-U-SM-R2 User manual
-
Black Box Black Box ServSwitch Wizard VGA (USB) User manual