KitchenAid 29.7 cu. ft. 48" Width User manual

SIDE BY SIDE BUILT-IN REFRIGERATOR

Installation Guide

IMPORTANT: READ AND

SAVE

THESE INSTRUCTIONS. INSTALLATION REQUIRES 2 OR MORE PEOPLE.

REFRIGERADOR EMPOTRADO

DE DOS PUERTAS

Manual de instalación

IMPORTANTE: LEA Y GUARDE ESTAS INSTRUCCIONES. LA INSTALACIÓN REQUIERE DE 2 O MÁS PERSONAS.

RÉFRIGÉRATEUR ENCASTRÉ CÔTE À CÔTE

Guide d’installation

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS. L’INSTALLATION NÉCESSITE L’INTERVENTION DE 2 PERSONNES OU PLUS.

Table of Contents/Índice/Table des matières ..................................................................2

2316565B

2

TABLE OF CONTENTS

REFRIGERATOR SAFETY .............................................................3

MODELS..........................................................................................4

INSTALLATION REQUIREMENTS................................................6

Tools and Parts ............................................................................6

Location Requirements................................................................6

Electrical Requirements ...............................................................7

Water Supply Requirements........................................................8

Tipping Radius .............................................................................8

Product Dimensions.....................................................................9

Door Swing Dimensions.............................................................10

Overlay Series Door Panel & Cabinetry Clearance....................11

Overlay Series Custom Panels and Handle Kits .......................13

Classic Series Factory Panels and Kits .....................................14

Classic Series Custom Panels...................................................15

Classic, Architect

®

and Complete Series

Custom Side Panels...................................................................16

Overlay Series Custom Side Panels..........................................17

INSTALLATION INSTRUCTIONS ................................................18

Unpack the Refrigerator.............................................................18

Reduce Tipping Radius..............................................................18

Move the Refrigerator into House..............................................19

Install Anti-Tip Boards................................................................19

Connect the Water Supply.........................................................19

Plug in Refrigerator.....................................................................21

Move Refrigerator to Final Location...........................................21

Level and Align Refrigerator.......................................................21

Install Classic Series Custom Panels.........................................22

Install Overlay Series Custom Panels........................................23

Adjust Doors...............................................................................24

Install Side Panel........................................................................25

Install Base Grille........................................................................25

Complete Installation..................................................................26

Water System Preparation .........................................................26

ÍNDICE

SEGURIDAD DEL REFRIGERADOR...........................................28

MODELOS.....................................................................................29

REQUISITOS DE INSTALACIÓN.................................................31

Piezas y herramientas................................................................31

Requisitos de ubicación.............................................................31

Requisitos eléctricos..................................................................32

Requisitos del suministro de agua.............................................33

Arco de vuelco ...........................................................................33

Medidas del producto................................................................34

Medidas de oscilación de las puertas .......................................35

Espacio para el panel de la puerta y para los gabinetes de

la serie Overlay...........................................................................36

Paneles a la medida y juegos de agarraderas de la serie

Overlay .......................................................................................38

Paneles y juegos de fábrica de la serie Classic ........................39

Paneles a la medida para la serie Classic .................................40

Paneles laterales a la medida para las series Classic,

Architect

®

y Complete................................................................41

Paneles laterales a la medida para la serie Overlay ..................42

INSTRUCCIONES DE INSTALACIÓN.........................................43

Desempaque el refrigerador ......................................................43

Cómo reducir el arco de vuelco.................................................43

Cómo hacer entrar el refrigerador en la casa ............................44

Cómo instalar los tableros antivuelco........................................44

Conexión del suministro de agua ..............................................45

Cómo enchufar el refrigerador...................................................46

Cómo mover el refrigerador a su ubicación final.......................46

Nivelación y alineamiento del refrigerador.................................46

Cómo instalar los paneles a la medida para la serie Classic ....47

Cómo instalar los paneles a la medida para la serie Overlay....48

Ajuste las puertas.......................................................................49

Cómo instalar el panel lateral.....................................................50

Cómo instalar la rejilla de la base ..............................................50

Cómo terminar la instalación .....................................................51

Preparación del sistema de agua ..............................................51

TABLE DES MATIÈRES

SÉCURITÉ DU RÉFRIGÉRATEUR ..............................................52

MODÈLES .....................................................................................53

EXIGENCES D’INSTALLATION...................................................55

Outillage et pièces......................................................................55

Exigences d’emplacement.........................................................55

Spécifications électriques .........................................................56

Spécifications de l’alimentation en eau.....................................57

Rayon de basculement ..............................................................57

Dimensions du produit...............................................................58

Dimensions pour le pivotement des portes...............................59

Série Overlay - Panneau de porte et placard - dimensions et

espace libre................................................................................60

Panneaux personnalisés et poignées de la série Overlay.........62

Ensembles de panneaux d'origine de la série Classic..............63

Panneaux personnalisés de la Série Classic.............................64

Panneaux latéraux personnalisés des Séries Classic,

Architect

®

et Complete ...............................................................65

Panneaux latéraux personnalisés de la Série Overlay ..............66

INSTRUCTIONS D’INSTALLATION.............................................67

Déballage du réfrigérateur..........................................................67

Réduction du rayon de basculement.........................................67

Faire entrer le réfrigérateur dans le domicile .............................68

Installation de planches antibasculement..................................68

Raccordement à la canalisation d'eau.......................................69

Brancher le réfrigérateur.............................................................70

Déplacement du réfrigérateur à l'emplacement final.................70

Réglage de l'aplomb et alignement du réfrigérateur .................70

Installation des panneaux personnalisés de la Série Classic....71

Installation des panneaux personnalisés de la Série Overlay ...72

Ajustement des portes ...............................................................73

Installation du panneau latéral ...................................................74

Installation de la grille de la base...............................................74

Achever l’installation ..................................................................75

Préparation du système d’eau...................................................75

3

REFRIGERATOR SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

4

MODELS

Side by Side Non-Dispensing Refrigerators

Architect

®

Series

Features wraparound styling that complements the contoured

door handles. This series provides a warm commercial-looking

built-in refrigerator.

KSSC36FTS KSSC42FTS KSSC48FTS

Classic Series

Features factory-installed, traditional style trim to provide a

“framed” look. This series requires the installation of custom

panels that are not included.

KSSS36FTX KSSS42FTX KSSS48FTX

Overlay Series

Features factory-installed, overlay style trim to provide a

“frameless” look. This series requires the installation of custom

panels, handles, and standoffs.

KSSO36FTX KSSO42FTX KSSO48FTX

5

Side by Side Dispensing Refrigerators

Architect

®

Series

Features wraparound styling that complements the contoured

door handles. This series provides a warm commercial-looking

built-in refrigerator.

KSSC36QTS KSSC42QTS KSSC48QTS

Classic Series

Features factory-installed, traditional style trim to provide a

“framed” look. This series requires the installation of custom

panels that are not included.

KSSS36QTB KSSS42QTB KSSS48QTB

KSSS36QTW KSSS42QTW KSSS48QTW

KSSS36QTX KSSS42QTX KSSS48QTX

Overlay Series

Features factory-installed, overlay style trim to provide a

“frameless” look. This series requires the installation of custom

panels, handles, and standoffs.

KSSO36QTB KSSO42QTB KSSO48QTB

Complete Series

Features factory-installed stainless steel trim and panels to create

a sleek, contemporary look.

KSSP36QTS KSSP42QTS KSSP48QTS

6

INSTALLATION REQUIREMENTS

Tools and Parts

IMPORTANT:

■ Installer: Leave Installation Instructions with the homeowner.

■ Homeowner: Keep Installation Instructions for future

reference. Save these Installation Instructions for the local

electrical inspector’s use.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

PARTS NEEDED:

■ Six #8 x 3" (7.6 cm) wood screws (longer screws may be needed)

■ One or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s)

■ Order factory panels, make custom panels or consult a

qualified cabinetmaker or carpenter to make the panels.

Classic Series: Order factory panels, make custom panels, or

consult a qualified cabinetmaker or carpenter to make the

panels. See “Classic Series Custom Panels” for more

information.

Overlay Series: Make custom panels, or consult a qualified

cabinetmaker or carpenter to make the panels. See “Overlay

Series Custom Panels and Handle Kits” for more information.

Architect

®

and Complete Series are shipped complete.

■ If you are connecting the water line directly to copper tubing

and not to a shutoff valve, you need a ferrule, a union, and a

¹⁄₄" (6.35 mm) compression fitting.

Location Requirements

The refrigerator can be recessed in an opening between cabinets

or installed at the end of a cabinet run using a side panel to

enclose the refrigerator.

IMPORTANT:

■ Observe all governing codes and ordinances.

■ It is recommended that you do not install the refrigerator near

an oven, radiator, or other heat source.

■ Do not install in a location where the temperature will fall

below 55°F (13°C).

■ Floor must support the refrigerator weight, more than 600 lbs

(272 kg), door panels and contents of the refrigerator.

■ Ceiling height must allow for side tipping radius. See “Tipping

Radius.”

■ Location should permit door to open fully. See “Door Swing

Dimensions.”

■ Location must permit top grille removal. See “Opening

Dimensions.”

Opening Dimensions

■ To avoid tipping during use, the solid soffit must be within 1"

(2.5 cm) maximum above the refrigerator. If the solid soffit is

higher than 1" (2.5 cm) or one is not available, then the

refrigerator must be braced.

If the anti-tip boards are needed, they must be attached to

the rear wall studs 80" to 90" (203 cm to 229 cm) above the

floor. See “Install Anti-Tip Boards” for more information.

NOTE: A clearance of ¹⁄₂" (1.3 cm) must be maintained above

the top grille in order for the top grille to be removed.

■ Hand drill or electric drill

(properly grounded)

■ Drill bits

■ Two adjustable wrenches

■ Phillips screwdriver

■ Small level

■ Appliance dolly

■ Torx

®†

T27 screwdriver

■ ¹¹⁄₃₂" nut driver

■ ³⁄₈" and ¹⁄₂" open-end

wrenches

■ ⁵⁄₃₂" Allen wrench

■ ¹⁄₄" and ⁵⁄₁₆" socket drivers

■ Tape measure

■ Utility knife

†®TORX is a registered trademark of Textron Innovations Inc.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

¹⁄₂"

(1.3 cm)

7

■ A grounded 3 prong electrical outlet should be placed within

4" (10.2 cm) of the right side cabinets or end panel. See

“Electrical Requirements” for more information.

■ The water shutoff should be located in the base cabinet on

either side of the refrigerator or some other easily accessible

area. If the water shutoff valve is not in the cabinets, the

plumbing for the water line can come through the floor or the

back wall. See “Water Supply Requirements” for more

information.

NOTE: Flooring under refrigerator must be at same level as

the room. Face of cabinetry must be plumb.

Electrical Requirements

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground

Fault Circuit Interrupter) protected outlet, nuisance tripping of the

power supply may occur, resulting in loss of cooling. Food quality

and flavor may be affected. If nuisance tripping has occurred,

and if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, remove the top grille and turn the master

power switch to OFF or disconnect power at the circuit breaker

box.

When you are finished, turn ON the master power switch or

reconnect power at the circuit breaker box. Then reset the control

to the desired setting.

Model Width A (as shown above)

36

42

48

35¹⁄₂" (90.2 cm) to 35³⁄₄" (90.8 cm)

41¹⁄₂" (105.4 cm) to 41³⁄₄" (106.1 cm)

47¹⁄₂" (120.7 cm) to 47³⁄₄" (121.3 cm)

80" - 90"

(203-229 cm)

4"

(10.2 cm)

6"

(15.2 cm)

83¹⁄₂" (212.1 cm) min.

84

³⁄₄" (215 cm) max.

to bottom of solid soffit

24"

(60.96 cm) min.

1"

(2.54 cm)

77"

(196 cm)

6"

(15.2 cm)

6"

(15.2 cm)

A

Width

(see chart following)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

8

Water Supply Requirements

■ All installations must meet local plumbing code requirements.

■ The water shutoff should be located in the base cabinet on

either side of the refrigerator or some other easily accessible

area. The right-hand side is recommended. The access hole

through the cabinet must be within ¹⁄₂" (12.7 mm) of the rear

wall.

NOTE: If the water shut off valve is in the back wall behind

the refrigerator, it must be at an angle so that the tube is not

kinked when the refrigerator is pushed into its final position.

■ If the water shutoff valve is not in the cabinets, the plumbing

for the water line can come through the floor. A ¹⁄₂" (12.7 mm)

hole for plumbing should be drilled at least 6" (15.2 cm) from

the right or left hand side cabinet or panel. On the floor, the

hole should be no more than 1" (2.54 cm) away from the back

wall. See “Connect the Water Supply.”

■ If additional tubing is needed, use copper tubing and check

for leaks. Install the copper tubing only in areas where the

household temperatures will remain above freezing.

■ Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle valve

which reduces water flow and clogs more easily.

NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"

(6.35 mm) saddle-type shutoff valve, a union, and copper

tubing. Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes.

Water Pressure

A cold water supply with water pressure between 30 and 120 psi

(207 and 827 kPa) is required to operate the water dispenser and

ice maker. If you have questions about your water pressure, call a

licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi

(207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

■ Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■ Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

■ If your refrigerator has a water filter cartridge, it may further

reduce the water pressure when used in conjunction with a

reverse osmosis system. Remove the water filter cartridge.

If you have questions about your water pressure, call a licensed,

qualified plumber.

Tipping Radius

Be sure there is adequate ceiling height to stand the refrigerator

upright when it is moved into place.

■ The dolly wheel height must be added to the tipping radius

when a dolly is used.

■ If needed, the tipping radius can be reduced. See “Reduce

Tipping Radius.”

Side Tipping Radius

The side tipping radius varies depending upon the width of the

model. Use the chart provided to determine the side tipping

radius.

NOTE: Tip on side only.

24"

(60.96 cm) min.

1"

(2.54 cm)

6"

(15.2 cm)

6"

(15.2 cm)

6"

(15.2 cm)

Model Tipping Radius A

36

42

48

90¹⁄₂" (229.9 cm)

93" (236.2 cm)

96" (243.8 cm)

A

9

Product Dimensions

Side View

■ The depth from the front of the top grille to the back of the

refrigerator cabinet is 25³⁄₈" (64.5 cm).

■ The power cord is 84" (213 cm) long.

■ The water line attached to the back of the refrigerator is 5 ft

(1.5 m) long.

■ Height dimensions are shown with leveling legs extended ¹⁄₈"

(3 mm) below the rollers.

*When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below

rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions.

Top View

Front View

■ Width dimensions were measured from trim edge to trim

edge.

■ Height dimensions are shown with leveling legs extended ¹⁄₈"

(3 mm) below the rollers.

*When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below

rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions.

Model Width A

36

42

48

35" (88.9 cm)

41" (104.1 cm)

47" (119.4 cm)

25³⁄₈"

(64.5 cm)

23¹⁄₂"

(59.7 cm)

84" (213.4 cm)

Power Cord

*83³⁄₈"

(211.8 cm)

*3

¹⁄₂" (8.9 cm)

25³⁄₈"

(64.5 cm)

A

Model Width A

(Trim edge to trim edge)

36

42

48

36¹⁄₄" (92.1 cm)

42¹⁄₄" (107.3 cm)

48¹⁄₄" (122.6 cm)

*83

³⁄₈

"

(211.8 cm)

A

(see chart following)

10

Door Swing Dimensions

The location must permit both doors to open to a minimum of

90°. Allow 4¹⁄₂" (11.4 cm) minimum space between the side of the

refrigerator and a corner wall.

NOTE: More clearance may be required if you are using overlay

panels, custom handles, or extended handles on a Classic

model.

To adjust the door swing, see “Adjust Doors.”

36" (91.4 cm) Models

42" (106.7 cm) Models

48" (121.9 cm) Models

130˚

90˚

110˚

44³⁄₈"

(112.7 cm

)

39"

(99.1 cm)

14

³⁄₈"

(36.5 cm)

10

⁷⁄₈"

(27.6 cm)

35

¹⁄₂"

(90.2 cm)

38

⁷⁄₈"

(

98.7 cm)

130˚

90˚

110˚

47⁷⁄₈"

(121.6 cm

)

41¹⁄₂"

(105.4 cm)

16

⁷⁄₈"

(42.9 cm)

12

⁵⁄₈"

(32.1 cm)

37

¹⁄₄"

(94.6 cm)

41

³⁄₈"

(105.1 cm)

130

˚

130˚

90˚

110˚

51³⁄₈"

(130.5 cm

)

44"

(111.8 cm)

19

¹⁄₄"

(48.9 cm)

14

³⁄₈"

(36.5 cm)

39"

(99.1 cm)

43

⁷⁄₈"

(

111.4 cm)

11

Overlay Series Door Panel & Cabinetry Clearance

The custom door panels and adjacent cabinetry must be designed so that there is sufficient clearance for the doors to swing open. If

the refrigerator is to be installed close to the wall, see “Door Swing 90°” on next page.

When the doors are closed the refrigerator will extend beyond the face of the adjacent cabinetry to some degree.

NOTE: For Overlay Series models, rout the

hinge side of the custom door panels to a

radius that is equal to at least half the

thickness of the panel if a 130˚ door swing is

desired. See “Adjust Doors.”

Spacer Panel

1

/4" (6.35 mm)

3

/4" (1.9 cm)

1" (2.5 cm)

1

/2" (1.3 cm)

1"

1

/4"

1

/2"

1"

(2.5 cm)

1

(3.2 cm)

1

/4"

1

(3.8 cm)

1

/2"

1

/2"

Refrigerator

Side Trim

Door

Hinge

Backer Panel

Overlay Panel

Door Swing 110˚

Actual Size

Refrigerator to

Cabinetry Clearance

(2.5 cm)

(3.2 cm)

(3.8 cm)

(1.3 cm)

NOTE: Allow ¹⁄₂"

(1.3 cm) clearance

between overlay

panel and cabinetry.

Cabinetry

3

/4"

(1.9 cm)

12

Allow a minimum of 4¹⁄₂" (11.4 cm) of space between the side of the refrigerator and a corner wall. More clearance may be needed if

thicker custom panels or custom handles are used. Do not overlook baseboards.

1

/4" (6.35 mm)

3

/4" (1.9 cm)

1" (2.5 cm)

1

/2" (1.3 cm)

3

/4"

1"

1

/4"

1

/2"

1

/2"

Refrigerator

Side Trim

Door

Backer Panel

Overlay Panel

Hinge

Door Swing 90˚

Actual Size

Refrigerator to

Cabinetry Clearance

(1.9 cm)

(2.5 cm)

(3.8 cm)

(1.3 cm)

(3.2 cm)

Spacer Panel

Cabinetry

1

/2"

3

/4"

1"

(1.3 cm)

(1.9 cm)

(2.5 cm)

90˚ Door

Stop Position

13

Overlay Series Custom Panels and Handle Kits

Custom overlay panels allow you to blend the exterior of your

refrigerator into the overall kitchen décor, and to use custom

handles for additional design flexibility.

The custom panels must have backer panels attached in order to

mount them to the refrigerator. It is most common to work with

three panels, as shown in the following graphic: a decorative

overlay panel, a ¹/₈" (3.18 mm) spacer panel or spacer strips and

a ¹/₄" (6.35 mm) backer panel.

In some cases, your cabinet manufacturer may choose to work

with one panel routed for the different dimensions. Follow these

panel dimension and placement instructions to be sure that the

custom overlay panels will fit properly.

IMPORTANT:

■ The weight of the refrigerator door overlay panel cannot

exceed 50 lbs (23 kg).

■ The weight of the freezer door overlay panel cannot exceed

40 lbs (18.1 kg).

■ The weight of the top grille overlay panel cannot exceed

10 lbs (4.5 kg).

To minimize panel weight, you may use 2" (5.08 cm) spacer strips

around the perimeter in place of full-sheet solid spacer panels.

The spacer strips must be set in at least 1" (2.54 cm) from the

top, bottom and sides edges of the backer panel. If you use

spacer strips, it is also recommended that you use two 2"

(5.08 cm) strips horizontally centered for added support.

NOTE: For the grille and the door panels to be flush, the overlay

door panel should be ¹⁄₄" (6.35 mm) thicker than the overlay grille

panel.

Overlay Panel

Spacer Panel

Backer Panel

5

/8" to

3

/4"

(15.88 to

19.05 mm)

1

/8"

(3.18 mm)

1

/4"

(6.35 mm)

1" minimum

(2.54 cm)

Door/Grille Trim

Spacer Panel

Offset Dimension

1

/8"

(3.18 mm)

Decorative Overlay Panels Backer Panels

Model A B C Model D E F

36 14³/₄" (37.47 cm) 19³/₄" (50.17 cm) 34³/₄" (88.27 cm) 36 14¹/₄" (36.20 cm) 19¹/₄" (48.90 cm) 34³/₄" (88.27 cm)

42 17¹/₄" (43.82 cm) 23¹/₄" (59.06 cm) 40³/₄" (103.51 cm) 42 16³/₄" (42.55 cm) 22³/₄" (57.79 cm) 40³/₄" (103.51 cm)

48 19³/₄" (50.17 cm) 26³/₄" (67.95 cm) 46³/₄" (118.75 cm) 48 19¹/₄" (48.90 cm) 26¹/₄" (66.68 cm) 46³/₄" (118.75 cm)

Bottom Offset

¹⁄₈" (3.2 mm)

Bottom Offset

¹⁄₈" (3.2 mm)

14

¹⁄₄"

(

36.2 cm)

33

⁷⁄₈"

(

86.0 cm)

B

AA

Freezer

Door Panel

(Non-Dispenser)

Refrigerator

Door Panel

C

D

DED

F

7

¹⁄₄"

(18.4 cm)

6

³⁄₁₆"

(15.7 cm)

Side Offset

¹⁄₄" (6.4 mm

)

10⁷⁄₈"

(27.6 cm)

P

referred

Radius

¹⁄₂"

(

1.27 cm)

72

¹⁄₄"

(183.5 cm)

Freezer

Door Panel

(Dispenser)

Top Offset

1

⁵⁄₈" (4.13 cm)

Bottom Offset

¹⁄₂" (1.27 cm)

22"

(55.9 cm)

33

¹⁄₄"

(84.5 cm)

70

¹⁄₂"

(179.1 cm)

70¹⁄₂"

(179.1 cm)

Handle-

Side Offset

¹⁄₄"

(6.4 mm)

Dispenser

cut-out is

centered

left-to-right

14

Overlay Series Door Handle Kits

The following handle styles are available. Contact your

KitchenAid dealer or KitchenAid Parts and Accessories at

1-800-442-9991. In Canada, call 1-800-807-6777.

Handles

These handles can be installed on side-by-side and bottom-

freezer refrigerators that require overlay panels.

*Available for non-dispensing models only.

Standoffs

(includes screws to support ³/₄" applications)

These standoffs can be installed on side-by-side and bottom-

freezer refrigerators that require overlay panels. (2 standoffs must

be ordered for each handle.) Handles and standoffs may be

combined to meet your individual decorating needs.

Architect

®

Series

Handles

Classic Series Factory Panels and Kits

All factory parts are available through your KitchenAid dealer or

by calling KitchenAid Parts and Accessories at 1-800-442-9991.

In Canada, call 1-800-807-6777.

Factory Door Panel Kits

Three kits containing colored acrylic or stainless steel door and

top grille panels are available. Follow the kit instructions for

installing the panels.

NOTE: Panel kits are not required for factory-installed stainless

steel panel models.

Door Panel Part Numbers for Non-dispenser Models

Door Panel Part Numbers for Dispenser Models

Extended Door Handle Kits

Use extended door handles when additional finger clearance is

needed between the door handles and custom panel. Follow the

kit instructions for installing the door handles.

A. Architect

®

Series handle (4396103)

B. Flat end straight handle (4396776) with stainless

steel clamshell standoffs (4396775)

C. Round end arc handle (4396779) with bronze bullet

standoffs (4396778)

D. Round end semicircle (4396777) with stainless

steel cylinder standoffs (4396782)

PART NO. DESCRIPTION

4396776 Flat End Straight - 21" (53.3 cm) Length,

Satin Stainless Steel

4396781 Flat End Straight - 45" (114.3 cm) Length,

Satin Stainless Steel

4396777 Round End Semicircle,

Satin Stainless Steel*

4396779 Round End Arc,

Satin Stainless Steel*

PART NO. DESCRIPTION

4396775 Clamshell, Satin Stainless Steel

4396780 Clamshell, Satin Bronze

4396774 Bullet, Satin Stainless Steel

4396778 Bullet, Satin Bronze

4396782 Cylinder, Satin Stainless Steel

4396773 Cylinder, Satin Bronze

AB C D

PART NO. COLOR

4396103 Stainless Steel

8171760 Biscuit

4396105 White

4396106 Black

Color 36 42 48

White #2325136 #2325137 #2325138

Black #2325139 #2325140 #2325141

Stainless Steel #2325142 #2325143 #2325144

Color 36 42 48

White #2325127 #2325128 #2325129

Black #2325130 #2325131 #2325132

Stainless Steel #2325133 #2325134 #2325135

Color Part Number

White #4387990

Black #8171418

Stainless Steel #4388062

Matte Aluminum #4387989

15

Classic Series Custom Panels

If you plan to install custom wood panels, you will need to create

the panels yourself or consult a qualified cabinetmaker or

carpenter. See dimension drawings for panel specifications.

IMPORTANT: Panels weighing more than recommended may

cause damage to your refrigerator.

NOTE: Dimensions shown have a (±) ¹⁄₁₆" (1.5 mm) tolerance.

Panels that are more than ¹⁄₄" (6.35 mm) thick must be routed. If

panels are less than ¹⁄₄" (6.35 mm) thick, install a filler panel

between the doors and decorative panels.

Top Grille Panel

The top grille panel should not weigh more than 10 lbs (4.5 kg).

Door Panels for Non-dispenser Models

The freezer panel should not weigh more than 40 lbs (18.1 kg).

The refrigerator panel should not weigh more than 50 lbs (23 kg).

Door Panels for Dispenser Models

The freezer panel should not weigh more than 40 lbs (18.1 kg).

The refrigerator panel should not weigh more than 50 lbs (23 kg).

NOTE: Dispenser cut-out is centered left-to-right.

Top Grille Panel – Routing Requirements

If the custom panels are thicker than ¹⁄₄" (6.35 mm), the top and

bottom edges of the top panel should be edge routed ¹⁄₂" (1.3 cm)

and ³⁄₈" (9.5 mm), respectively. Both ends should be edge routed

⁷⁄₈" (2.2 cm) as shown.

Model A

36

42

48

34¹⁄₄" (87.0 cm)

40¹⁄₄" (102.2 cm)

46¹⁄₄" (117.5 cm)

Model A B

36

42

48

14¹⁄₄" (36.2 cm)

16³⁄₄" (42.6 cm)

19¹⁄₄" (48.9 cm)

22³⁄₄" (57.8 cm)

26¹⁄₄" (66.7 cm)

A

7"

(17.8 cm)

70¹⁄₂"

(179.1 cm)

A B

Model A B

36

42

48

14¹⁄₄" (36.2 cm)

16³⁄₄" (42.6 cm)

19¹⁄₄" (48.9 cm)

22³⁄₄" (57.8 cm)

26¹⁄₄" (66.7 cm)

70⁷⁄₁₆"

(179 cm)

14¹⁄₄"

(36.2 cm)

33³⁄₄"

(85.7 cm)

A B

10⁷⁄₈"

(27.6 cm)

¹⁄₄"

(6.35 mm)

max.

¹⁄₄"

(6.35 mm)

Top

Grille

¹⁄₄

"

(6.35 mm)

max.

¹⁄₄"

(6.35 mm)

Top

Grille

34¹⁄₈" (86.68 cm)

16

Door Panels – Routing Requirements

If the custom panels are thicker than ¹⁄₄" (6.35 mm), then all edges

of the panels must be routed. If the standard handle is used,

route the entire handle side of both panels 3¹⁄₄" (8.25 cm) to allow

for finger clearance. Then route the other sides 1" (2.54 cm).

Standard Handle – Top View

If an extended handle kit is used, route the handle side ¹⁄₄"

(6.35 mm). All other routing dimensions would remain the same

as the standard handle. Make sure your product location will

allow doors with extended handles to be opened to 90 degrees.

See “Door Swing Dimensions.”

For more information on ordering extended handles, see “Classic

Series Factory Panels and Kits.”

NOTE: For both types of handles, route the top and bottom

edges ¹⁄₂" (1.3 cm).

Door Panel - Side View

Extended Handle - Top View

Classic, Architect

®

and Complete Series

Custom Side Panels

Custom side panels may be needed when not enough space is

available to have cabinets on both sides of the refrigerator or

when the refrigerator is placed at the end of a cabinet run. You

may choose an Inset, Flush, or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type

of installation you are planning.

NOTES:

■ The dimensions shown are actual product dimensions

and may not reflect the needed panel installation

dimensions.

■ The side panel should be a minimum of ½" (1.27 cm) thick

to avoid warping.

■ If the opening depth is 25" (63.5 cm) or more, you may

want to install a support board on rear wall.

Refrigerator

¹⁄₂"

(1.3 cm)

min.

¹⁄₄"

(6.35 mm) max.

Top

Bottom

¹⁄₂"

(1.3 cm)

min.

¹⁄₄"

(6.35 mm) max.

Center face

detail between

offsets

7"

(17.8 cm)

³⁄₄"

(1.9 cm)

2" (5 cm)

min.

¹⁄₄" (6.35 mm) max.

3¹⁄₄"

(8.25 cm)

min.

Door

Panel

Handle

1"

(2.54 cm)

Door

Panel

Hinge Side

¹⁄₂" (1.3 cm)

min.

¹⁄₄"

(6.35 mm)

max.

Panel

¹⁄₄"

(6.35 mm)

Door

Panel

Handle

1"

(2.54 cm)

Door

Panel

Hinge Side

1"

(2.54 cm)

max

24¹⁄₈"

(61.3 cm)

23

¹⁄₂"

(59.7 cm)

23¹¹⁄₁₆"

(60.3 cm)

17

Side Trim

Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall. Add ⁷⁄₃₂" (5.6 mm) to this measurement to allow the side

panel to fit into the trim.

2. If the panel is more than ¹⁄₄" (6.35 mm) thick, route the front

edge to allow the side panel to fit into the trim.

Flush Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall.

2. Attach the support board with a screw or adhesive that is

compatible with aluminum and wood.

Recessed Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall.

2. Route the front edge of the support board or attach a ¹⁄₄"

(6.35 mm) board to hold the panel in the cabinet side trim.

Overlay Series Custom Side Panels

Custom side panels may be needed when not enough space is

available to have cabinets on both sides of the refrigerator or

when the refrigerator is placed at the end of a cabinet run. You

may choose an Inset or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type

of installation you are planning.

NOTES:

■ The dimensions shown are actual product dimensions

and may not reflect the needed installation dimensions.

■ The side panel should be a minimum of ½" (1.27 cm) thick

to avoid warping.

■ If the opening depth is 25" (63.5 cm) or more, you may

want to install a support board on rear wall.

Refrigerator

Side Trim

¹¹⁄₆₄"

(4.5 mm)

¹⁄₄"

(6.35 mm)

³⁄₁₆"

(4.7 mm)

⁷⁄₃₂"

(5.5 mm)

¹³⁄₃₂" (10 mm)

⁵⁄₈"

(15.7 mm)

A

23¹¹⁄₁₆"

(60.16 cm)

Overlay

³⁄₁₆"

(4.5 mm)

³⁄₈"

(9.7 mm)

¹⁄₁₆"

(1.5 mm)

³⁄₃₂"

(2.38 mm)

18

Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall. Add ¹⁄₃₂" (0.8 mm) to this measurement to allow the side

panel to fit into the trim.

2. If the panel is more than ³⁄₈" (9.5 mm) thick, route the front

edge to allow the side panel to fit into the trim.

Recessed Inset Installation Dimensions

1. Measure the distance from point A (as shown) to back wall.

2. Route the front edge of the support board or attach a ³⁄₈"

(9.5 mm) board to hold the panel in the cabinet side trim.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

IMPORTANT:

■ Do not remove the protective film until the refrigerator is in its

operating position.

■ All four leveling legs must contact the floor to support and

stabilize the full weight of the refrigerator.

■ Keep the cardboard shipping piece or plywood under the

refrigerator until it is installed in the operating position.

1. Remove and save the literature package bag taped to the

side of the refrigerator and the parts bag behind the grille.

Remove the four brackets (two on each side) that attach the

shipping base to the refrigerator bottom.

NOTE: Do not remove tape and door bracing until the

refrigerator is in its final position.

2. If necessary, reduce the tipping radius. See “Tipping Radius”

for ceiling height requirements or “Reduce Tipping Radius”

for step-by-step instructions. If you do not need to reduce the

tipping radius, proceed to “Move the Refrigerator into

House.”

Reduce Tipping Radius

(if required)

Before bringing the refrigerator into the home, be sure there is

adequate ceiling height to stand the refrigerator upright. See

“Tipping Radius” in the “Installation Requirements” section for

more information.

If you do not have adequate ceiling height to stand the

refrigerator upright, the tipping radius can be reduced by

removing the top grille and side trims (see the following chart).

1. Grasp both ends of the top grille.

2. Push the top grille straight up; then pull straight out. Lay the

grille on a soft surface.

3. Remove the six screws attaching each cabinet side trim to

the refrigerator and remove the side trims.

A

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

Model Reduced Tipping Radius

36 88" (223.5 cm)

42 88¹⁄₂" (224.8 cm)

48 89¹⁄₄" (226.7 cm)

A. Top grille

B. Cabinet side trim

B BA

19

Move the Refrigerator into House

1. Place an appliance dolly under the left side of the refrigerator

as shown. Be sure to protect the side trims and handles.

Place the corner posts from the packing materials over the

trims and handles as appropriate. Slowly tighten the strap.

NOTE: Pass the dolly strap under the handles for the

Architect

®

Series.

2. Place pieces of the shipping carton on the floor when rolling

the dolly and refrigerator into the house. Move the refrigerator

close to the built-in opening.

3. Place top of cardboard carton or plywood under refrigerator.

4. Stand the refrigerator up. First, place the left bottom edge of

the refrigerator on the floor, stand the refrigerator upright and

then lower the right-hand side of the refrigerator to the floor.

5. Do not remove protective film or cover.

6. Reassemble the trim and top grille after the dolly has been

removed from the refrigerator.

Install Anti-Tip Boards

IMPORTANT:

■ To avoid tipping during use, the solid soffit must be within 1"

(2.5 cm) maximum above the refrigerator. If the solid soffit is

higher than 1" (2.5 cm) or one is not available, then the

refrigerator must be braced.

■ It is recommended that board(s) be installed before the

refrigerator is installed.

■ Board(s) must be long enough to fully cover the width of the

compressor cover.

■ Locate the board(s) so the bottom surface(s) of the board(s)

is(are) 84" (213 cm) from the floor.

■ During installation, raise the refrigerator up so there is ¹⁄₄"

(6.35 mm) maximum between the top of the refrigerator and

the bottom of the anti-tip board(s). Do not crush the

compressor cover when raising the rear leveling legs.

To Install Anti-tip Boards

1. Mark the stud locations on rear wall 80" to 90" (203 cm to

229 cm) above floor.

2. Securely attach one or two 2" x 4" x 32" (5 cm x 10 cm x

81 cm) boards to wall studs behind refrigerator. Use six

#8 x 3" (7.6 cm) (or longer) wood screws. The wood screws

must be screwed into the studs at least 1½" (3.8 cm). The

board(s) must overlap the compressor cover.

Connect the Water Supply

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line

is connected, turn the ice maker OFF.

Style 1 - Shutoff Valve Connection

NOTE: If your water line connection does not look like Style 1,

see “Style 2 - Copper Line Connection.”

1. Unplug refrigerator or disconnect power supply.

IMPORTANT: Before attaching the tubing to shutoff valve, flush

the main water supply line to remove particles and air in the water

line. Allow enough flow so that water becomes clear. Flushing the

water line may help avoid filters and/or water valves from

becoming clogged.

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

A. Center board

¹⁄₄

" (6.35 mm) max. above refrigerator

B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards

C. Attach to studs with six #8 x 3" (7.6 cm) screws

D. Compressor cover

BA

C

2" (5 cm)

D

20

2. Remove the shipping tape from the gray, coiled water tubing

on the rear of the refrigerator.

3. Thread the provided nut onto the shutoff valve as shown.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

6. Plug in the refrigerator or reconnect power.

7. Flush the water system. See “Water System Preparation.”

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to

completely fill ice container.

Style 2 - Copper Line Connection

Connecting to Water Line

NOTE: If existing water line meets the “Water System

Requirements,” see “Connecting to Refrigerator.”

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a ½" to 1¹⁄₄" (1.25 cm to 3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

■ Make sure it is a cold water pipe.

■ Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the lower left rear of refrigerator to the

water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄"

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure

both ends of copper tubing are cut square.

5. Using a grounded drill, drill a ¹⁄₄" (6.35 mm) hole in the cold

water pipe you have selected.

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the ¹⁄₄" (6.35 mm)

drilled hole in the water pipe and that the washer is under the

pipe clamp. Tighten the packing nut. Tighten the pipe clamp

screws slowly and evenly so washer makes a watertight seal.

Do not overtighten, or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten

the clamp or the sleeve. This will crush the copper tubing.

IMPORTANT: Before attaching the tubing to shutoff valve, flush

the main water supply line to remove particles and air in the water

line. Allow enough flow so that water becomes clear. Flushing the

water line may help avoid filters and/or water valves from

becoming clogged.

8. Turn off the shutoff valve on the water pipe. Coil the copper

tubing.

9. Check for leaks around the saddle valve.

Connecting to Refrigerator

1. Unplug the refrigerator or disconnect power.

2. Remove the shipping tape from the gray, coiled water tubing

on the rear of the refrigerator.

3. Measure the distance from the shutoff valve to the opening in

which the refrigerator will be located. Tubing must be

extended from the shutoff valve into the refrigerator opening

following specific guidelines. See “Water Supply

Requirements.”

4. A ¹⁄₄" x ¹⁄₄" (6.35 mm to 6.35 mm) coupling is needed in order

to connect the water tubing to an existing household water

line. Thread the provided nut onto the coupling on the end of

the copper tubing.

5. Turn shutoff valve ON.

6. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

7. Plug in the refrigerator or reconnect power.

8. Flush the water system. See “Water System Preparation.”

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to

completely fill ice container.

A. Bulb

B. Nut

C. Water tubing

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

A

B

C

A

B

C

DEF

G

A. Water tubing

B. Nut

C. Bulb

D. Coupling (purchased)

E. Ferrule (purchased)

F. Nu t (p urchas ed )

G. Household water line (as

connected in previous section)

A B C D E F G

Page is loading ...

KitchenAid 29.7 cu. ft. 48" Width User manual

This manual is also suitable for

KitchenAid 29.7 cu. ft. 48" Width User manual

in other languages

Related papers

Other documents