KitchenAid W10681447A User manual

SIDE BY SIDE BUILT-IN REFRIGERATOR

Installation Guide

IMPORTANT: READ AND

SAVE

THESE INSTRUCTIONS. INSTALLATION REQUIRES 2 OR MORE PEOPLE.

REFRIGERADOR EMPOTRADO

DE DOS PUERTAS

Guía de instalación

IMPORTANTE: LEA Y GUARDE ESTAS INSTRUCCIONES. LA INSTALACIÓN REQUIERE DE 2 O MÁS PERSONAS.

RÉFRIGÉRATEUR ENCASTRÉ CÔTE À CÔTE

Guide d’installation

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS. L’INSTALLATION NÉCESSITE L’INTERVENTION DE 2 PERSONNES OU PLUS.

Table of Contents/Índice/Table des matières ..................................................................2

W10681447A

2

TABLE OF CONTENTS

REFRIGERATOR SAFETY........................................................................... 3

MODELS....................................................................................................... 4

INSTALLATION REQUIREMENTS .............................................................5

Tools and Parts......................................................................................... 5

Location Requirements.............................................................................5

Electrical Requirements............................................................................6

Water Supply Requirements.....................................................................7

Tipping Radius..........................................................................................7

Product Dimensions ................................................................................. 8

Door Swing Dimensions ........................................................................... 9

Overlay Series Door Panel and Cabinetry Clearance ............................10

Overlay Series Custom Panels and Handle Kits ....................................12

Architect

®

Series Custom Side Panels ...................................................13

Overlay Series Custom Side Panels.......................................................14

INSTALLATION INSTRUCTIONS............................................................. 15

Unpack the Refrigerator ......................................................................... 15

Reduce Tipping Radius .......................................................................... 15

Move the Refrigerator into House .......................................................... 16

Install Anti-Tip Boards ............................................................................ 16

Connect the Water Supply ..................................................................... 16

Plug in Refrigerator................................................................................. 18

Move Refrigerator to Final Location....................................................... 18

Level and Align Refrigerator ................................................................... 18

Install Overlay Series Custom Panels .................................................... 19

Adjust Doors ........................................................................................... 20

Install Side Panel .................................................................................... 21

Install Base Grille .................................................................................... 21

Complete Installation.............................................................................. 22

Water System Preparation ..................................................................... 22

ÍNDICE

SEGURIDAD DEL REFRIGERADOR........................................................23

MODELOS..................................................................................................24

REQUISITOS DE INSTALACIÓN..............................................................25

Herramientas y piezas ............................................................................25

Requisitos de ubicación .........................................................................25

Requisitos eléctricos...............................................................................27

Requisitos del suministro de agua .........................................................27

Arco de vuelco........................................................................................28

Medidas del producto............................................................................. 28

Medidas de oscilación de las puertas....................................................29

Espacio para el panel de la puerta y para los

armarios de la serie de paneles recubiertos ..........................................30

Paneles a la medida y juegos de agarraderas

de la serie de paneles recubiertos..........................................................32

Paneles laterales a la medida para las series Architect

®

.......................33

Paneles laterales a la medida para la serie de paneles recubiertos......34

INSTRUCCIONES DE INSTALACIÓN...................................................... 35

Desempaque el refrigerador................................................................... 35

Cómo reducir el arco de vuelco ............................................................. 35

Cómo hacer entrar el refrigerador en la casa ........................................ 36

Cómo instalar los tableros antivuelco.................................................... 36

Conexión del suministro de agua........................................................... 37

Cómo enchufar el refrigerador ............................................................... 38

Cómo mover el refrigerador a su ubicación final................................... 39

Nivelación y alineamiento del refrigerador............................................. 39

Cómo instalar los paneles a la medida

para la serie de paneles recubiertos ...................................................... 40

Ajuste las puertas ................................................................................... 40

Cómo instalar el panel lateral................................................................. 42

Cómo instalar la rejilla de la base........................................................... 42

Cómo terminar la instalación.................................................................. 43

Preparación del sistema de agua........................................................... 43

TABLE DES MATIÈRES

SÉCURITÉ DU RÉFRIGÉRATEUR ...........................................................44

MODÈLES ..................................................................................................45

EXIGENCES D’INSTALLATION................................................................46

Outillage et pièces ..................................................................................46

Exigences d’emplacement .....................................................................46

Spécifications électriques.......................................................................48

Spécifications de l’alimentation en eau..................................................48

Rayon de basculement...........................................................................49

Dimensions du produit............................................................................49

Dimensions pour l'ouverture des portes ................................................50

Série Panneaux décoratifs—

Panneau de porte et placard—espace libre...........................................51

Panneaux personnalisés et poignées de la série Panneaux décoratifs 53

Panneaux latéraux personnalisés des séries Architect

®

........................54

Panneaux latéraux personnalisés de la série Panneaux décoratifs....... 55

INSTRUCTIONS D’INSTALLATION ......................................................... 56

Déballage du réfrigérateur...................................................................... 56

Réduction du rayon de basculement ..................................................... 57

Faire entrer le réfrigérateur dans le domicile.......................................... 57

Installation de planches antibasculement.............................................. 57

Raccordement à l’alimentation en eau................................................... 58

Branchement du réfrigérateur ................................................................ 59

Déplacement du réfrigérateur à l'emplacement final............................. 60

Réglage de l’aplomb et alignement du réfrigérateur.............................. 60

Installation des panneaux personnalisés

de la série Panneaux décoratifs............................................................. 61

Ajustement des portes............................................................................ 61

Installation du panneau latéral................................................................ 63

Installation de la grille de la base ........................................................... 63

Achever l’installation............................................................................... 64

Préparation du système d’eau ............................................................... 64

3

REFRIGERATOR SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

4

MODELS

Side by Side Non-Dispensing Refrigerators

Architect

®

Series

Features wraparound styling that complements the contoured

door handles. This series provides a warm commercial-looking

built-in refrigerator.

KSSC36FTS KSSC42FTS KSSC48FTS

Overlay Series

Features factory-installed, overlay style trim to provide a “frameless”

look. This series requires the installation of custom panels, handles,

and standoffs.

KSSO36FTX KSSO42FTX KSSO48FTX

Side by Side Dispensing Refrigerators

Architect

®

Series

Features wraparound styling that complements the contoured door

handles. This series provides a warm commercial-looking built-in

refrigerator.

KSSC36QTS KSSC42QTS KSSC48QTS

5

INSTALLATION REQUIREMENTS

Tools and Parts

IMPORTANT:

■ Installer: Leave Installation Instructions with the homeowner.

■ Homeowner: Keep Installation Instructions for future

reference. Save these Installation Instructions for the local

electrical inspector’s use.

Tools Needed

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Parts Needed

■ #8 x 3" (7.6 cm) wood screws (longer screws may be needed) (6)

■ 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s) (1 or 2)

■ Order factory panels, make custom panels or consult a

qualified cabinetmaker or carpenter to make the panels.

Classic Series: Order factory panels, make custom panels, or

consult a qualified cabinetmaker or carpenter to make the

panels. See “Classic Series Custom Panels” for more

information.

Overlay Series: Make custom panels, or consult a qualified

cabinetmaker or carpenter to make the panels. See “Overlay

Series Custom Panels and Handle Kits” for more information.

Architect

®

and Complete Series are shipped complete.

■ If you are connecting the water line directly to copper tubing

and not to a shutoff valve, you need a ferrule, a union, and a

¹⁄₄" (6.35 mm) compression fitting.

Location Requirements

The refrigerator can be recessed in an opening between cabinets

or installed at the end of a cabinet run using a side panel to

enclose the refrigerator.

IMPORTANT:

■ Observe all governing codes and ordinances.

■ It is recommended that you do not install the refrigerator near

an oven, radiator, or other heat source.

■ Do not install in a location where the temperature will fall

below 55°F (13°C).

■ Floor must support the refrigerator weight, more than 600 lbs

(272 kg), door panels and contents of the refrigerator.

■ Ceiling height must allow for side tipping radius. See “Tipping

Radius.”

■ Location should permit door to open fully. See “Door Swing

Dimensions.”

■ Location must permit top grille removal. See “Opening

Dimensions.”

Opening Dimensions

■ To avoid tipping during use, the solid soffit must be within 1"

(2.5 cm) maximum above the refrigerator. If the solid soffit is

higher than 1" (2.5 cm) or one is not available, then the

refrigerator must be braced.

If anti-tip boards are needed, they must be installed to the rear

wall studs so that the bottom of the anti-tip board is 84"

(213.4 cm) from the floor. See “Install Anti-Tip Boards” for

more information.

NOTES:

■ A clearance of ¹⁄₂" (1.3 cm) must be maintained above the

top grille in order for the top grille to be removed.

■ Do not remove the foam gasket on top of the compressor

cover unless removal is necessary to fit the unit under a

soffit. Removal of the gasket will cause loss in cooling

efficiency.

■ If installing under a solid soffit, after installation raise the

leveling legs so that the gasket is pressed snugly against

the soffit.

■ A grounded 3 prong electrical outlet should be located within

a specified number of inches from the right-hand side

cabinets or end panel. See the chart following the graphic for

the number of inches required for your model. For more

information, see “Electrical Requirements.”

■ The water shutoff should be located in the base cabinet on

either side of the refrigerator or some other easily accessible

area. If the water shutoff valve is not in the cabinets, the

plumbing for the water line can come through the floor or the

back wall. See “Water Supply Requirements” for more

information.

■ Cordless drill

■ Drill bits

■ Adjustable

wrenches (2)

■ Phillips screwdriver

■ Small level

■ Appliance dolly

■ Torx

®†

T27 screwdriver

■ ¹¹⁄₃₂" nut driver

■ ³⁄₈" and ¹⁄₂" open-end wrenches

■ ⁵⁄₃₂" hex key

■ ¹⁄₄" and ⁵⁄₁₆" socket drivers

■ Tape measure

■ Utility knife

†®TORX is a registered trademark of Saturn Fasteners, Inc.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

A. Gasket

B. Compressor cover

¹⁄₂"

(1,3 cm)

B

A

6

NOTE: Flooring under refrigerator must be at same level as the

room. Face of cabinetry must be plumb.

Electrical Requirements

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 volt, 60 Hz., AC only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground Fault

Circuit Interrupter) protected outlet, nuisance tripping of the

power supply may occur, resulting in loss of cooling. Food quality

and flavor may be affected. If nuisance tripping has occurred, and

if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, remove the top grille and turn the master

power switch to OFF or disconnect power at the circuit breaker

box.

When you are finished, turn ON the master power switch or

reconnect power at the circuit breaker box. Then reset the control

to the desired setting.

Model

Width A

(as shown

above)

Width A for

Overlay Models

(as shown above)

Dimension B

(as shown

above)

36 35¹⁄₂" to 35³⁄₄"

(90.2 cm to

90.8 cm)

35³⁄₄" to 36"

(90.8 cm to 91.4 cm)

4" (10.2 cm)

42 41¹⁄₂" to 41³⁄₄"

(105.4 cm to

106.1 cm)

41³⁄₄" to 42"

(105.4 cm to

106.7 cm)

7¹⁄₂" (19.1 cm)

48 47¹⁄₂" to 47³⁄₄"

(120.7 cm to

121.3 cm)

47³⁄₄" to 48"

(121.3 cm to

121.9 cm)

13¹⁄₂" (34.3 cm)

6"

(15.2 cm)

24"

(60.96 cm) min.

1"

(2.54 cm)

77"

(196 cm)

6"

(15.2 cm)

6"

(15.2 cm)

A

Width

(see chart following)

B

Dimension

84" (213.4 cm)

to bottom of solid soffit

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

7

Water Supply Requirements

■ All installations must meet local plumbing code requirements.

■ The water shutoff should be located in the base cabinet on

either side of the refrigerator or some other easily accessible

area. The right-hand side is recommended. The access hole

through the cabinet must be within ¹⁄₂" (12.7 mm) of the rear

wall.

NOTE: If the water shutoff valve is in the back wall behind the

refrigerator, it must be at an angle so that the tube is not

kinked when the refrigerator is pushed into its final location.

■ If the water shutoff valve is not in the cabinets, the plumbing

for the water line can come through the floor. A ¹⁄₂" (12.7 mm)

hole for plumbing should be drilled at least 6" (15.2 cm) from

the right or left hand side cabinet or panel. On the floor, the

hole should be no more than 1" (2.54 cm) away from the back

wall. See “Connect the Water Supply.”

■ If additional tubing is needed, use copper tubing and check

for leaks. Install the copper tubing only in areas where the

household temperatures will remain above freezing.

■ Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle valve

which reduces water flow and clogs more easily.

NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"

(6.35 mm) saddle-type shutoff valve, a union, and copper

tubing. Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes.

Water Pressure

A cold water supply with water pressure between 30 and 120 psi

(207 and 827 kPa) is required to operate the water dispenser and

ice maker. If you have questions about your water pressure, call a

licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

■ Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■ Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

■ If your refrigerator has a water filter cartridge, it may further

reduce the water pressure when used in conjunction with a

reverse osmosis system. Remove the water filter cartridge.

If you have questions about your water pressure, call a licensed,

qualified plumber.

Tipping Radius

Be sure there is adequate ceiling height to stand the refrigerator

upright when it is moved into place.

■ The dolly wheel height must be added to the tipping radius

when a dolly is used.

■ If needed, the tipping radius can be reduced. See “Reduce

Tipping Radius.”

Side Tipping Radius

The side tipping radius varies depending upon the width of the

model. Use the chart provided to determine the side tipping

radius.

NOTE: Tip on side only.

24"

(60.96 cm) min.

1"

(2.54 cm)

6"

(15.2 cm)

6"

(15.2 cm)

6"

(15.2 cm)

Model Tipping Radius A

36 90¹⁄₂" (229.9 cm)

42 93" (236.2 cm)

48 96" (243.8 cm)

A

8

Product Dimensions

Side View

■ The depth from the front of the top grille to the back of the

refrigerator cabinet is 25³⁄₈" (64.5 cm).

■ The power cord is 84" (213 cm) long.

■ The water line attached to the back of the refrigerator is 5 ft

(1.5 m) long.

■ Height dimensions are shown with leveling legs extended ¹⁄₈"

(3 mm) below the rollers.

*When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below

rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions.

Top View

Front View

■ Width dimensions were measured from trim edge to trim

edge.

■ Height dimensions are shown with leveling legs extended ¹⁄₈"

(3 mm) below the rollers.

*When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below

rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions.

Model Width A

36 35" (88.9 cm)

42 41" (104.1 cm)

48 47" (119.4 cm)

25³⁄₈"

(64.5 cm)

23¹⁄₂"

(59.7 cm)

84" (213.4 cm)

Power Cord

*83³⁄₈"

(211.8 cm)

*3

¹⁄₂" (8.9 cm)

25³⁄₈"

(64.5 cm)

A

Model Width A (Trim edge to trim edge)

36 36¹⁄₄" (92.1 cm)

42 42¹⁄₄" (107.3 cm)

48 48¹⁄₄" (122.6 cm)

*83³⁄₈"

(211.8 cm)

A

(see chart following)

9

Door Swing Dimensions

The location must permit both doors to open to a minimum of 90°.

Allow 4¹⁄₂" (11.4 cm) minimum space between the side of the

refrigerator and a corner wall.

NOTE: More clearance may be required if you are using overlay

panels, custom handles, or extended handles on a Classic model.

To adjust the door swing, see “Adjust Doors.”

36" (91.4 cm) Models

42" (106.7 cm) Models

48" (121.9 cm) Models

130˚

90˚

110˚

44³⁄₈"

(112.7 cm)

39"

(99.1 cm)

14

³⁄₈"

(36.5 cm)

10

⁷⁄₈"

(27.6 cm)

35

¹⁄₂"

(90.2 cm)

38

⁷⁄₈"

(98.7 cm)

130˚

90˚

110˚

47⁷⁄₈"

(121.6 cm)

41¹⁄₂"

(105.4 cm)

16

⁷⁄₈"

(42.9 cm)

12

⁵⁄₈"

(32.1 cm)

37

¹⁄₄"

(94.6 cm)

41

³⁄₈"

(105.1 cm)

130˚

90˚

110˚

51³⁄₈"

(130.5 cm)

44"

(111.8 cm)

19

¹⁄₄"

(48.9 cm)

14

³⁄₈"

(36.5 cm)

39"

(99.1 cm)

43

⁷⁄₈"

(111.4 cm)

10

Overlay Series Door Panel and Cabinetry Clearance

The custom door panels and adjacent cabinetry must be designed so that there is sufficient clearance for the doors to swing open. If

the refrigerator is to be installed close to the wall, see “Door Swing 90°” on next page.

When the doors are closed the refrigerator will extend beyond the face of the adjacent cabinetry to some degree.

NOTE: For Overlay Series models, rout the

hinge side of the custom door panels to a

radius that is equal to at least half the

thickness of the panel if a 130˚ door swing is

desired. See “Adjust Doors.”

Spacer Panel

1

/4" (6.35 mm)

3

/4" (1.9 cm)

1" (2.5 cm)

1

/2" (1.3 cm)

1"

1

/4"

1

/2"

1"

(2.5 cm)

1

(3.2 cm)

1

/4"

1

(3.8 cm)

1

/2"

1

/2"

Refrigerator

Side Trim

Door

Hinge

Backer Panel

Overlay Panel

Door Swing 110˚

Actual Size

Refrigerator to

Cabinetry Clearance

(2.5 cm)

(3.2 cm)

(3.8 cm)

(1.3 cm)

NOTE: Allow ¹⁄₂"

(1.3 cm) clearance

between overlay

panel and cabinetry.

Cabinetry

3

/4"

(1.9 cm)

11

Allow a minimum of 4¹⁄₂" (11.4 cm) of space between the side of the refrigerator and a corner wall. More clearance may be needed if

thicker custom panels or custom handles are used. Do not overlook baseboards.

1

/4" (6.35 mm)

3

/4" (1.9 cm)

1" (2.5 cm)

1

/2" (1.3 cm)

3

/4"

1"

1

/4"

1

/2"

1

/2"

Refrigerator

Side Trim

Door

Backer Panel

Overlay Panel

Hinge

Door Swing 90˚

Actual Size

Refrigerator to

Cabinetry Clearance

(1.9 cm)

(2.5 cm)

(3.8 cm)

(1.3 cm)

(3.2 cm)

Spacer Panel

Cabinetry

1

/2"

3

/4"

1"

(1.3 cm)

(1.9 cm)

(2.5 cm)

90˚ Door

Stop Position

12

Overlay Series Custom Panels and Handle Kits

Custom overlay panels allow you to blend the exterior of your

refrigerator into the overall kitchen décor, and to use custom

handles for additional design flexibility.

The custom panels must have backer panels attached in order to

mount them to the refrigerator. It is most common to work with

three panels, as shown in the following graphic: a decorative

overlay panel, a ¹/₈" (3.18 mm) spacer panel or spacer strips and a

¹/₄" (6.35 mm) backer panel.

In some cases, your cabinet manufacturer may choose to work

with one panel routed for the different dimensions. Follow these

panel dimension and placement instructions to be sure that the

custom overlay panels will fit properly.

IMPORTANT:

■ The weight of the refrigerator door overlay panel cannot

exceed 50 lbs (23 kg).

■ The weight of the freezer door overlay panel cannot exceed

40 lbs (18.1 kg).

■ The weight of the top grille overlay panel cannot exceed

10 lbs (4.5 kg).

To minimize panel weight, you may use 2" (5.08 cm) spacer strips

around the perimeter in place of full-sheet solid spacer panels.

The spacer strips must be set in at least 1" (2.54 cm) from the top,

bottom and sides edges of the backer panel. If you use spacer

strips, it is also recommended that you use two 2" (5.08 cm) strips

horizontally centered for added support.

Decorative Overlay Panel

*Represents placement of dispenser frame.

Overlay Panel

Spacer Panel

Backer Panel

⁵⁄₈

" to

³⁄₄

"

(15.88 to

19.05 mm)

¹⁄₈

"

(3.18 mm)

¹⁄₄

"

(6.35 mm)

1" minimum

(2.54 cm)

Door/Grille Trim

Spacer Panel

Offset Dimension

¹⁄₈

"

(3.18 mm)

Overlay Panel

Backer Panel

Model A B C

36 14³/₄" (37.47 cm) 19³/₄" (50.17 cm) 34³/₄" (88.27 cm)

42 17¹/₄" (43.82 cm) 23¹/₄" (59.06 cm) 40³/₄" (103.51 cm)

48 19³/₄" (50.17 cm) 26³/₄" (67.95 cm) 46³/₄" (118.75 cm)

B

A

Freezer

Door Panel

(Non-Dispenser)

Refrigerator

Door Panel

C

7

¹⁄₄"

(18.4 cm)

72

¹⁄₄"

(183.5 cm)

Grille Panel

13

Backer Panels

NOTES:

■ Dashed lines represent placement of backer panels on overlay

panels.

■ Illustration shows backer panels placed on decorative

overlays.

Overlay Series Door Handle Kits

The following handle style is available. Contact your KitchenAid

dealer or KitchenAid Parts and Accessories at

1-800-442-9991. In Canada, call 1-800-807-6777.

Architect

®

Series

Handles

Architect

®

Series Custom Side Panels

Custom side panels may be needed when not enough space is

available to have cabinets on both sides of the refrigerator or

when the refrigerator is placed at the end of a cabinet run. You

may choose an Inset, Flush, or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of

installation you are planning.

NOTES:

■ The dimensions shown are actual product dimensions and

may not reflect the needed panel installation dimensions.

■ The side panel should be a minimum of ½" (1.27 cm) thick

to avoid warping.

■ If the opening depth is 25" (63.5 cm) or more, you may

want to install a support board on rear wall.

Refrigerator

Model D E F

36 14¹/₄" (36.20 cm) 19¹/₄" (48.90 cm) 33³/₄" (85.73 cm)

42 16³/₄" (42.55 cm) 22³/₄" (57.79 cm) 39³/₄" (100.97 cm)

48 19¹/₄" (48.90 cm) 26¹/₄" (66.68 cm) 45³/₄" (116.21 cm)

Bottom Offset

¹⁄₈" (3.2 mm)

AB

C

6

³⁄₁₆"

(15.7 cm)

Side Offset

¹⁄₂" (12.7 mm)

Top Offset

1

⁵⁄₈" (4.13 cm)

Bottom Offset

¹⁄₂" (1.27 cm)

70

¹⁄₂"

(179.1 cm)

70¹⁄₂"

(179.1 cm)

Handle-

Side Offset

¹⁄₄"

(6.4 mm)

A. Architect

®

Series handle (4396103)

Part Number Color

4396103 Stainless Steel

8171760 Biscuit

4396105 White

4396106 Black

A

24¹⁄₈"

(61.3 cm)

23

¹⁄₂"

(59.7 cm)

23¹¹⁄₁₆"

(60.3 cm)

14

Side Trim

Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall. Add ⁷⁄₃₂" (5.6 mm) to this measurement to allow the side

panel to fit into the trim.

2. If the panel is more than ¹⁄₄" (6.35 mm) thick, route the front

edge to allow the side panel to fit into the trim.

Flush Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall.

2. Attach the support board with a screw or adhesive that is

compatible with aluminum and wood.

Recessed Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall.

2. Route the front edge of the support board or attach a ¹⁄₄"

(6.35 mm) board to hold the panel in the cabinet side trim.

Overlay Series Custom Side Panels

Custom side panels may be needed when not enough space is

available to have cabinets on both sides of the refrigerator or

when the refrigerator is placed at the end of a cabinet run. You

may choose an Inset or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of

installation you are planning.

NOTES:

■ The dimensions shown are actual product dimensions and

may not reflect the needed installation dimensions.

■ The side panel should be a minimum of ½" (1.27 cm) thick

to avoid warping.

■ If the opening depth is 25" (63.5 cm) or more, you may

want to install a support board on rear wall.

Refrigerator

Side Trim

¹¹⁄₆₄"

(4.5 mm)

¹⁄₄"

(6.35 mm)

³⁄₁₆"

(4.7 mm)

⁷⁄₃₂"

(5.5 mm)

¹³⁄₃₂" (10 mm)

⁵⁄₈"

(15.7 mm)

A

23¹¹⁄₁₆"

(60.16 cm)

Overlay

³⁄₁₆"

(4.5 mm)

³⁄₈"

(9.7 mm)

¹⁄₁₆"

(1.5 mm)

³⁄₃₂"

(2.38 mm)

15

Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall. Add ¹⁄₃₂" (0.8 mm) to this measurement to allow the side

panel to fit into the trim.

2. If the panel is more than ³⁄₈" (9.5 mm) thick, route the front

edge to allow the side panel to fit into the trim.

Recessed Inset Installation Dimensions

1. Measure the distance from point A (as shown) to back wall.

2. Route the front edge of the support board or attach a ³⁄₈"

(9.5 mm) board to hold the panel in the cabinet side trim.

INSTALLATION

INSTRUCTIONS

Unpack the Refrigerator

IMPORTANT:

■ Do not remove the film covering until the refrigerator is in its

operating location.

■ All four leveling legs must contact the floor to support and

stabilize the full weight of the refrigerator.

■ Keep the cardboard shipping piece or plywood under the

refrigerator until it is installed in the operating location.

1. Remove and save the literature package bag taped to the side

of the refrigerator and the parts bag behind the grille. Remove

the four brackets (two on each side) that attach the shipping

base to the refrigerator bottom.

NOTE: Do not remove tape and door bracing until the

refrigerator is in its final location.

2. If necessary, reduce the tipping radius. See “Tipping Radius”

for ceiling height requirements or “Reduce Tipping Radius” for

step-by-step instructions. If you do not need to reduce the

tipping radius, proceed to “Move the Refrigerator into House.”

Reduce Tipping Radius

(if required)

Before bringing the refrigerator into the home, be sure there is

adequate ceiling height to stand the refrigerator upright. See

“Tipping Radius” in the “Installation Requirements” section for

more information.

If you do not have adequate ceiling height to stand the refrigerator

upright, the tipping radius can be reduced by removing the top

grille and side trims (see the following chart).

1. Grasp both ends of the top grille.

2. Push the top grille straight up; then pull straight out. Lay the

grille on a soft surface.

3. Remove the six screws attaching each cabinet side trim to the

refrigerator and remove the side trims.

A

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

Model Reduced Tipping Radius

36 89" (225.9 cm)

42 90¹⁄₂" (229.9 cm)

48 91¹⁄₄" (231.8 cm)

A. Top grille

B. Cabinet side trim

B BA

16

Move the Refrigerator into House

1. Place an appliance dolly under the left side of the refrigerator

as shown. Place the corner posts from the packing materials

over the trims and handles as appropriate to avoid damage.

Slowly tighten the strap.

NOTE: Pass the dolly strap under the handles for the

Architect

®

Series.

2. Place pieces of the shipping carton on the floor when rolling

the dolly and refrigerator into the house. Move the refrigerator

close to the built-in opening.

3. Place top of cardboard carton or plywood under refrigerator.

4. Stand the refrigerator up. First, place the left bottom edge of

the refrigerator on the floor, stand the refrigerator upright and

then lower the right-hand side of the refrigerator to the floor.

5. Reassemble the trim and top grille after the dolly has been

removed from the refrigerator.

Install Anti-Tip Boards

IMPORTANT:

■ To avoid tipping during use, the solid soffit must be within

1" (2.5 cm) maximum above the refrigerator. If the solid soffit is

higher than 1" (2.5 cm) or one is not available, then the

refrigerator must be braced.

■ It is recommended that board(s) be installed before the

refrigerator is installed.

■ Board(s) must be long enough to fully cover the width of the

compressor cover.

■ Locate the board(s) so the bottom surface(s) of the board(s)

is(are) 84" (213 cm) from the floor.

■ During installation, raise the refrigerator up so there is

¹⁄₄" (6.35 mm) maximum between the top of the refrigerator

and the bottom of the anti-tip board(s). Do not crush the

compressor cover when raising the rear leveling legs.

NOTE: The foam gasket, on top of the compressor cover, will

compress to fit under the anti-tip board(s). There is no need to

trim the gasket.

To Install Anti-tip Boards

1. Mark the stud locations on rear wall.

2. Securely attach one or two 2" x 4" x 32" (5 cm x 10 cm x

81 cm) boards to wall studs behind refrigerator. Use six

#8 x 3" (7.6 cm) (or longer) wood screws. The wood screws

must be screwed into the studs at least 1½" (3.8 cm). The

board(s) must overlap the compressor cover.

Connect the Water Supply

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line is

connected, turn the ice maker OFF.

Connect to Water Line

Parts Needed

■ Minimum 7 ft (2.13 m) flexible, codes approved water

supply line

Style 1—Shutoff Valve Connection

NOTE: If your water line connection does not look like Style 1, see

“Style 2—Copper Line Connection.”

1. Unplug refrigerator or disconnect power supply.

IMPORTANT:

■ There is not enough clearance to achieve a flush installation if

a water shutoff valve is located in the wall behind the

refrigerator. The water shutoff should be located in the base

cabinet on either side of the refrigerator.

■ Before attaching the tubing to shutoff valve, flush the main

water supply line to remove particles and air in the water line.

Allow enough flow so that water becomes clear. Flushing the

water line may help avoid filters and/or water valves from

becoming clogged.

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

A. Center board

¹⁄₄

" (6.35 mm) max.

above refrigerator

B. Two 2" x 4" x 32" (5 cm x 10 cm x

81 cm) boards

C. Attach to studs with six

#8 x 3" (7.6 cm) screws

D. Compressor cover

BA

C

2" (5 cm)

D

17

2. Connect the flexible, codes approved water supply line to the

water shutoff valve by threading the provided nut onto the

shutoff valve as shown.

3. Place the end of the tubing into a bucket, and turn shutoff

valve ON.

4. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Style 2—Copper Line Connection

NOTE: If there is a water supply line that meets the specifications

in “Water Supply Requirements,” proceed to “Connecting to

Refrigerator.” If not, use the following instructions to connect to

the household cold water supply.

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a ½" to 1¹⁄₄" (1.25 cm to 3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

■ Make sure it is a cold water pipe.

■ Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and keep normal sediment from collecting in the

valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the refrigerator to the water pipe. Add

7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄" (6.35 mm) O.D.

(outside diameter) copper tubing. Be sure both ends of copper

tubing are cut square.

5. Using a cordless drill, drill a ¹⁄₄" (6.35 mm) hole in the cold

water pipe you have selected.

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the ¹⁄₄" (6.35 mm)

drilled hole in the water pipe and that the washer is under the

pipe clamp. Tighten the packing nut. Tighten the pipe clamp

screws slowly and evenly so washer makes a watertight seal.

Do not overtighten.

IMPORTANT: Before attaching the tubing to shutoff valve, flush

the main water supply line to remove particles and air in the water

line. Allow enough flow so that water becomes clear. Flushing the

water line may help avoid filters and/or water valves from

becoming clogged.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten the

clamp or the sleeve. This will crush the copper tubing.

8. Turn off the shutoff valve on the water pipe. Coil the copper

tubing.

9. Connect the flexible, codes approved water supply line to the

water shutoff valve by threading the provided nut onto the

shutoff valve.

10. Place the end of the tubing into a bucket, and turn shutoff

valve ON.

11. Check for leaks around the saddle valve. Tighten any nuts or

connections (including connections at the valve) that leak.

Connect to Refrigerator

Parts Supplied

■ ¹⁄₄" to ¹⁄₄" (6.35 mm to 6.35 mm) male-to-male coupling

NOTE: The flexible, codes approved water supply line should

connect to the supply valve through the floor.

1. Unplug the refrigerator or disconnect power.

2. Connect the 7 ft (2.13 m) flexible codes approved water tube

to the water supply valve.

3. Flush the main water supply line to remove particles and air in

the water line. Allow enough flow so that water becomes clear.

4. Tape the 7 ft (2.13 m) flexible codes approved water supply

line to the floor, 7" (17.78 cm) from the left side of the

refrigerator. Tape along the length of the tubing, which will

allow it to pass beneath the refrigerator without interference.

NOTE: Allow a minimum of 26" (66.04 cm) of flexible codes

approved water supply line to be loose at the front of the

refrigerator for connecting to the refrigerator.

A. Bulb

B. Nut

C. Water tubing

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

A

B

C

A

B

C

DEF

G

1"

(2.54 cm)

7"

(17.78 cm)

6"

(15.2 cm)

6"

(15.2 cm)

18

5. Connect the 7 ft (2.13 m) flexible codes approved water

supply line to the refrigerator.

NOTE: If the main water shutoff valve is behind the

refrigerator, a secondary water shutoff valve may be installed

in line with the water supply line at the front of the product.

6. Turn on the water supply valve and check all connections for

leaks.

Plug in Refrigerator

1. Set control switch at top of cabinet to the OFF position.

2. Plug into a grounded 3 prong outlet.

Move Refrigerator to Final Location

IMPORTANT: To avoid floor damage, make sure levelers are

raised (not touching floor) and refrigerator is on rollers before

moving.

1. Place top of cardboard carton or plywood under refrigerator.

Remove dolly.

2. Do not remove film or cover.

3. Move the refrigerator straight back and evenly into the

opening. Be sure that the refrigerator side trims are not

interfering with the door opening. Also, be sure that the water

tubing is not kinked and the power supply cord is on top of the

refrigerator.

Level and Align Refrigerator

IMPORTANT: All four leveling legs must contact the floor to

support and stabilize the full weight of refrigerator. Rollers are for

moving refrigerator and not for permanent support.

After moving the refrigerator to its final location:

A. Household water line

B. Nut (purchased)

C. Ferrule (purchased)

D. Coupling

E. Bulb

F. Nu t

G. Refrigerator water tubing

A

B

C

D

E

F

G

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

19

1. Use a ⁵⁄₁₆" socket driver to turn the leveling bolts clockwise to

extend the legs to the floor as shown. The rollers should be off

the floor.

2. Adjust the leveling legs to level and align the refrigerator from

left to right and front to back so that the refrigerator is level

and aligned with the cabinetry. The cabinetry surface must be

plumb for the ideal fit of the refrigerator side trim.

3. Continue adjusting all of the leveling legs to raise the

refrigerator until the top is within at least 1" (2.54 cm) of the

top soffit.

NOTE: If an anti-tip board has been used, adjust the leveling

legs until the top of the refrigerator is within ¹⁄₄" (6.35 mm) of

the bottom of the anti-tip board as shown. Do not crush the

compressor cover.

IMPORTANT: Adjust in small increments to keep from

damaging the cabinet trim and causing problems with

the door alignment or top grille fit. To avoid damage to

the cabinet or leveling legs, do not apply more than

50 inch-pounds (5.65 Nm) of torque to the leveling bolts.

The leveling legs can be extended to a maximum of 1¹⁄₄"

(3.18 cm) below the rollers.

4. For Overlay models, additional adjustments may be needed

after the custom panels are installed.

Install Overlay Series Custom Panels

IMPORTANT:

■ Install the custom handles prior to installing the panels on the

refrigerator. For more information on KitchenAid custom

handle selection, refer to the KitchenAid Catalog, visit

www.kitchenaid.com, or call 1-800-442-9991. In Canada,

visit www.KitchenAid.ca, or call 1-800-807-6777.

■ Create custom door overlay panels according to the

specifications in the “Overlay Series Custom Panels” section.

■ KitchenAid is not responsible for the removal or addition of

molding or decorative panels that would not allow access to

the refrigerator for service.

Door Panel Installation

1. Remove all tape and door bracing from the refrigerator and

freezer doors.

2. Open the refrigerator and freezer compartment doors.

3. Remove the handle-side and top trims.

4. Slide the custom panels into the bottom and hinge side trims

on the refrigerator compartment and freezer compartment

doors, making sure that the backer panel fits into the hinge

side trims.

A. Rear leveling bolt

B. Front leveling bolt

A. Center board

¹⁄₄

" (6.35 mm) max. above refrigerator

B. 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards (2)

C. Attach to studs with six #8 x 3" (7.6 cm) screws

D. Compressor cover

A B

A

B

BA

C

2" (5 cm)

D

¹⁄₄" (6 mm)

max.

A. Trims

A. Panels

A

AA

20

5. Reinstall the handle-side and top trims.

6. Remove the skin from the screw covers. Slide or snap the

screw covers into the handle trim section.

7. Check refrigerator level and alignment. Adjust if needed.

Adjust Doors

Door Height Adjustment

Use the following steps to adjust the door height, up or down,

after the doors have been leveled.

1. Open the freezer or refrigerator door. Locate the bottom hinge

and remove the door stop screw.

Classic and Architect

®

Models

Remove the door stop screw from the bottom side of the

hinge with a ³⁄₈" open end wrench.

Overlay Models

Remove the 2 door stop screws: one from the bottom side

using a ³⁄₈" open end wrench and one from the top side using

a ⁵⁄₃₂" hex key.

2. Remove the locking plate as shown.

3. Turn the bushing located underneath the bottom of the hinge

using a ¹⁄₂" open end wrench. Turning the bushing to the left

will lower the door. Turning the bushing right will raise the

door.

4. After adjusting, check the doors to make sure they are even at

the top and bottom. If the doors are not even, continue to turn

the bushing to adjust the door height.

5. Replace the locking plate.

6. Turn the bushing slightly to align the hinge and locking plate

screw holes.

7. Replace the door stop screw or screws and tighten.

IMPORTANT: Do not place the door stop screw in the 130°

position on Overlay Series models unless the custom panels

have been routed on the hinge side. See “Overlay Series Door

Panel and Cabinetry Clearance.”

8. Recheck to make sure the doors are aligned and even.

Door Swing Adjustment

1. Check that the refrigerator door can open freely. If the door

opens too wide, remove the door stop screw or screws

(depending on your model) from the bottom hinge. See “Door

Height Adjustment” earlier in this section.

2. Hold the door open to a position that is less than 90°.

3. Replace the door stop screw or screws in the bottom hinge

and tighten.

A. Bushing

B. Door stop screw

C. Locking plate

A. Door stop screw from bottom

B. Door stop screw from top (110°)

A BC

AB

A. 130°

B. 110° (Overlay series)

C. 90°

AB C

Page is loading ...

KitchenAid W10681447A User manual

KitchenAid W10681447A User manual

in other languages

Related papers

Other documents