C-SM_INST_9-10
INSTALL INSTRUCTIONS C-SM SERIES
ANGLED HEAVY DUTY CONSOLE & ACCESSORIES
TOOLS REQUIRED:
Standard socket set w/ 6”extension
Metric socket set w/ 6” extension
Standard wrench set
Metric wrench set
Torx bit set w/ driver
Slide ¼” nuts into extrusion.
This can be done on inside of
console at top of extrusion.
Tunnel Plate (C-TMW-xx)
(Part # varies depending on vehicle type)
Pentex Printer
Mount
(C-PMS)
Console Extension
(C-SM-600, 800 or
1200)
Angled Heavy Duty
Console
(C-SM-830 or 1225)
Keyboard/Laptop
Platform
(C-SM-SA-1)
Monitor Platform
(C-SM-MMP)
C-SM_INST_9-10
Always!
¾ Read all instructions before installing any Havis, Inc. products.
¾ Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!
¾ Use hardware provided with install kit
SUB ASSEMBLY:
1. Install Tunnel Mount into vehicle. (See Tunnel Mount
specific install instructions.)
2. Determine desired height of console and console
accessories prior to mounting in vehicle.
INSTALLATION:
1. ADJUST CONSOLE HEIGHT: (See Figure #1)
• To adjust height remove carriage bolts on side
of console.
• Mount necessary accessories to side of console.
(Monitor platform, keyboard/laptop platform,
printer, etc. See instructions below.)
• With all accessories and height determined, re-attach
carriage bolts and nuts to console.
2. ATTACH MONITOR PLATFORM: (See Figure #2)
• Mounting platform attaches to side of console using
supplied carriage bolts and serrated nuts.
• Monitor mounting platform will mount to front row of
holes on console.
• Attach C-UMM-101 and C-MM-XXX brackets to
monitor platform prior to attaching to console.
Note: Prior to mounting accessories to side of Angled Heavy Duty console
be sure to adjust height.
3. ATTACH KEYBOARD/LAPTOP PLATFORM:
(See Figure #3)
• Mounting platform attaches to side of console using supplied
• carriage bolts and serrated nuts.
• When using platform for a keyboard, mount on rear rows
of holes on console.
• When using platform for a laptop, you have the option of using
any row of holes for desired height.
• Attach tilt / swivel, keyboard/laptop mount to swing arm assembly.
RE: C-MD-202, C-KBM-101 (sold separate)
Note: Prior to mounting accessories to side of Angled Heavy Duty console be sure to adjust height.
Height Adjustment
Figure #1
Figure #2
Mounts to sides of
Console
Figure #3
Mounts to sides of
Console
C-SM_INST_9-10
4. ATTACH PENTEX PRINTER BRACKET: (See Figure #4)
• Printer bracket attaches to front side of console.
• When mounted properly, printer housing will slide toward passenger side seat.
• Attach to Angled Heavy Duty console using supplied screws and Keps nuts.
5. MOUNT CONSOLE TO TUNNEL PLATE:
• Slide ¼-20 x ¾” bolts into slots of Tunnel Plate.
• Place Angled Heavy Duty console over ¼” bolts.
• Position console and attach to Tunnel using ¼-20 serrated nuts.
6. ATTACH CONSOLE EXTENSION: (C-SM-600, 800, 1200 see Figure 5)
• With Angled Heavy Duty console attached to Tunnel, position and attach 6” console
extension. **A spare plastic end cap is provided in case you choose not to attach
consoles together. Simply peel and stick to console end plate if desired.
• Slide (2) ¼-20 x ¾” hex head bolts into slots of Tunnel Plate.
• Place console extension and bolt down using ¼-20 serrated nuts.
• Connect opposite end-to-end plate of Angled Heavy Duty housing. (Slot to slot).
Adjust height as desired.
• Wire and install control heads and accessories.
Mounts to
Angled Heavy
Duty console
Mounting
Hardware
Figure #4
Figure #5
Tunnel Plate
Hardware
A spare plastic end
cap is provided in
case you choose not
to attach consoles
together
SWING ARM
PLASTIC WASHER COMES
WITH C-MD-200 ASSEMBLY
CM003105
C-MD-203
TOP REMOVED
FOR CLARITY
5/16" BELLEVILLE
WASHER GSM31091
5/16-24 CONICAL NUT
GSM30160
5/16-24 JAM NUT
GSM30070
1/4-20 X 1-1/2"
LG BOLT CM86504
METAL PLATE CM003103-1
COMES WITH C-MD-200
ASSEMBLY
SWING ARM
1/4-20 X 1-1/2"
LG BOLT
CM86504
PLASTIC WASHER CM003105
LARGE COMES WITH
SWING ARM ASSEMBLY
METAL PLATE GSM31020
COMES WITH
SWING ARM ASSEMBLY
C-3075-3 OR ANY OTHER
NON C-MD-200
SERIES ASSEMBLY
5/16" BELLEVILLE
WASHER GSM31091
5/16-24 CONICAL NUT
GSM30160
5/16-24 JAM NUT
GSM30070
C-SM-SA-1-HD ASSEMBLY
WITH C-MD-200 SERIES
STANDARD
C-SM-SA-1-HD ASSEMBLY
5/16-24 CONICAL NUT
GSM30160
5/16" BELLEVILLE WASHER
GSM31091
METAL PLATE CM003103-1
COMES WITH C-MD-200
ASSEMBLY
PLASTIC WASHER
CM003105 COMES
WITH C-MD-200
ASSEMBLY
C-MD-203
TOP REMOVED
FOR CLARITY
1/4-20 X 1-1/2"
LG BOLT
CM86504
STAINLESS STEEL
FENDER WASHER
(SPACERS) GSM31059
5/16-24 JAM NUT
GSM30070
SWING ARM
C-SM-SA-1 ASSEMBLY
WITH C-MD-200 SERIES
/