Havis C-SM-SA User manual

Brand: Havis

Model: C-SM-SA

Category: Car kits

Type: User manual

This manual is also suitable for

C-SM-1225

Havis C-SM-SA is an angled heavy-duty console and accessory system designed for use in vehicles. It offers height adjustment, allowing you to customize the positioning of your accessories for optimal viewing and reach. The console features mounting platforms for monitors, keyboards, laptops, and printers, providing a versatile workspace solution. With its durable construction and easy installation, the Havis C-SM-SA is ideal for organizing and securing your equipment in a variety of vehicle applications.

C-SM_INST_9-10

INSTALL INSTRUCTIONS C-SM SERIES

ANGLED HEAVY DUTY CONSOLE & ACCESSORIES

TOOLS REQUIRED:

Standard socket set w/ 6”extension

Metric socket set w/ 6” extension

Standard wrench set

Metric wrench set

Torx bit set w/ driver

Slide ¼” nuts into extrusion.

This can be done on inside of

console at top of extrusion.

Tunnel Plate (C-TMW-xx)

(Part # varies depending on vehicle type)

Pentex Printer

Mount

(C-PMS)

Console Extension

(C-SM-600, 800 or

1200)

Angled Heavy Duty

Console

(C-SM-830 or 1225)

Keyboard/Laptop

Platform

(C-SM-SA-1)

Monitor Platform

(C-SM-MMP)

C-SM_INST_9-10

Always!

¾ Read all instructions before installing any Havis, Inc. products.

¾ Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!

¾ Use hardware provided with install kit

SUB ASSEMBLY:

1. Install Tunnel Mount into vehicle. (See Tunnel Mount

specific install instructions.)

2. Determine desired height of console and console

accessories prior to mounting in vehicle.

INSTALLATION:

1. ADJUST CONSOLE HEIGHT: (See Figure #1)

• To adjust height remove carriage bolts on side

of console.

• Mount necessary accessories to side of console.

(Monitor platform, keyboard/laptop platform,

printer, etc. See instructions below.)

• With all accessories and height determined, re-attach

carriage bolts and nuts to console.

2. ATTACH MONITOR PLATFORM: (See Figure #2)

• Mounting platform attaches to side of console using

supplied carriage bolts and serrated nuts.

• Monitor mounting platform will mount to front row of

holes on console.

• Attach C-UMM-101 and C-MM-XXX brackets to

monitor platform prior to attaching to console.

Note: Prior to mounting accessories to side of Angled Heavy Duty console

be sure to adjust height.

3. ATTACH KEYBOARD/LAPTOP PLATFORM:

(See Figure #3)

• Mounting platform attaches to side of console using supplied

• carriage bolts and serrated nuts.

• When using platform for a keyboard, mount on rear rows

of holes on console.

• When using platform for a laptop, you have the option of using

any row of holes for desired height.

• Attach tilt / swivel, keyboard/laptop mount to swing arm assembly.

RE: C-MD-202, C-KBM-101 (sold separate)

Note: Prior to mounting accessories to side of Angled Heavy Duty console be sure to adjust height.

Height Adjustment

Figure #1

Figure #2

Mounts to sides of

Console

Figure #3

Mounts to sides of

Console

C-SM_INST_9-10

4. ATTACH PENTEX PRINTER BRACKET: (See Figure #4)

• Printer bracket attaches to front side of console.

• When mounted properly, printer housing will slide toward passenger side seat.

• Attach to Angled Heavy Duty console using supplied screws and Keps nuts.

5. MOUNT CONSOLE TO TUNNEL PLATE:

• Slide ¼-20 x ¾” bolts into slots of Tunnel Plate.

• Place Angled Heavy Duty console over ¼” bolts.

• Position console and attach to Tunnel using ¼-20 serrated nuts.

6. ATTACH CONSOLE EXTENSION: (C-SM-600, 800, 1200 see Figure 5)

• With Angled Heavy Duty console attached to Tunnel, position and attach 6” console

extension. **A spare plastic end cap is provided in case you choose not to attach

consoles together. Simply peel and stick to console end plate if desired.

• Slide (2) ¼-20 x ¾” hex head bolts into slots of Tunnel Plate.

• Place console extension and bolt down using ¼-20 serrated nuts.

• Connect opposite end-to-end plate of Angled Heavy Duty housing. (Slot to slot).

Adjust height as desired.

• Wire and install control heads and accessories.

Mounts to

Angled Heavy

Duty console

Mounting

Hardware

Figure #4

Figure #5

Tunnel Plate

Hardware

A spare plastic end

cap is provided in

case you choose not

to attach consoles

together

SWING ARM

PLASTIC WASHER COMES

WITH C-MD-200 ASSEMBLY

CM003105

C-MD-203

TOP REMOVED

FOR CLARITY

5/16" BELLEVILLE

WASHER GSM31091

5/16-24 CONICAL NUT

GSM30160

5/16-24 JAM NUT

GSM30070

1/4-20 X 1-1/2"

LG BOLT CM86504

METAL PLATE CM003103-1

COMES WITH C-MD-200

ASSEMBLY

SWING ARM

1/4-20 X 1-1/2"

LG BOLT

CM86504

PLASTIC WASHER CM003105

LARGE COMES WITH

SWING ARM ASSEMBLY

METAL PLATE GSM31020

COMES WITH

SWING ARM ASSEMBLY

C-3075-3 OR ANY OTHER

NON C-MD-200

SERIES ASSEMBLY

5/16" BELLEVILLE

WASHER GSM31091

5/16-24 CONICAL NUT

GSM30160

5/16-24 JAM NUT

GSM30070

C-SM-SA-1-HD ASSEMBLY

WITH C-MD-200 SERIES

STANDARD

C-SM-SA-1-HD ASSEMBLY

5/16-24 CONICAL NUT

GSM30160

5/16" BELLEVILLE WASHER

GSM31091

METAL PLATE CM003103-1

COMES WITH C-MD-200

ASSEMBLY

PLASTIC WASHER

CM003105 COMES

WITH C-MD-200

ASSEMBLY

C-MD-203

TOP REMOVED

FOR CLARITY

1/4-20 X 1-1/2"

LG BOLT

CM86504

STAINLESS STEEL

FENDER WASHER

(SPACERS) GSM31059

5/16-24 JAM NUT

GSM30070

SWING ARM

C-SM-SA-1 ASSEMBLY

WITH C-MD-200 SERIES

Havis C-SM-SA User manual

Brand: Havis

Model: C-SM-SA

Category: Car kits

Type: User manual

This manual is also suitable for

C-SM-1225

Download PDF

report

Havis C-SM-SA User manual

This manual is also suitable for

Havis C-SM-SA User manual

Related papers

Other documents