2. aspenhome
  3. IUAB-301-1

aspenhome IUAB-301-1 Assembly Instructions

  • Hello! I am an AI chatbot trained to assist you with the aspenhome IUAB-301-1 Assembly Instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
079HWPACK-74-1 INST
74-1
PROTECTIVE BLANKET
THREADED
INSERTS
ATTACHING ADJUSTABLE DESK BASE TO DESK TOP
1. TO AVOID SCRATCHING DESK TOP & FLOOR SURFACE, BEFORE OPENING BOXES, PLACE A PROTECTIVE BLANKET DOWN.
2. UN-BOX THE ADJUSTABLE DESK BASE AND FOLLOW THE ASSEMBLY INSTRUCTIONS PROVIDED
3. UN-BOX DESK TOP AND WITH THE AID OF A SECOND PERSON, ROTATE DESK TOP AND PLACE ONTO BLANKET.
4. WITH THE AID OF A SECOND PERSON, ROTATE ADJUSTABLE DESK BASE, PLACE IT ON BOTTOM OF DESK TOP AND LINE UP ADJUSTABLE DESK BASE HOLES WITH
DESK TOP INSERTS (FOR ADJUSTING DESK BASE WIDTH READ ASSEMBLY INSTRUCTIONS PROVIDED)
5. SECURE ADJUSTABLE DESK BASE TO DESK TOP USING THE (8)
5
8
CAP SCREWS PROVIDED IN THIS DESK TOP HARDWARE PACK. (TIGHTEN CAP SCREWS UNTIL SNUG,
DO NOT OVER TIGHTEN!)
PAGE 1 OF 2
DESK TOP
(BOTTOM VIEW)
ADJUSTABLE DESK BASE
(SOLD SEPARATELY)
LIFT DESK ASSEMBLY INSTRUCTIONS FOR
LIFT MECHANISM MODEL # IUAB-301-1
E
A
C
B
F
HARDWARE LIST
No. Description Sketch Quantity
A
5
16
" X
5
8
" CAP SCREWS 8 PCS
B
5
16
" WASHERS 8 PCS
C
5
16
" LOCK WASHERS 8 PCS
D ALLEN HEAD KEY 1 PCS
E PLASTIC WIRE CLIPS 6 PCS
F WOOD SCREWS 10 PCS
079HWPACK-74-1 INST
LIFT DESK ASSEMBLY INSTRUCTIONS FOR
LIFT MECHANISM MODEL # IUAB-301-1
PAGE 2 OF 2
DESK TOP
(BOTTOM VIEW)
CONTROL UNIT
(SOLD WITH ADJUSTABLE DESK BASE)
SCREWS
6. ATTACH ADJUSTABLE DESK BASE CONTROL UNIT TO EITHER THE RIGHT OR LEFT HARDWOOD CORNER BLOCK (SCREWS
PROVIDED WITH ADJUSTABLE DESK BASE)
7. CLIP THE POWER CORD INTO THE (6) PLASTIC WIRE CLIPS AND SCREW WIRE CLIPS TO THE RIGHT & LEFT THREADED INSERT
PANELS (DO NOT SCREW WIRE CLIPS INTO DESK TOP)
8. WITH THE AID OF A SECOND PERSON, LIFT & ROTATE DESK TO IT'S UPRIGHT POSITION.
9. HOOK METAL POWER PACK SUPPORT TRAY TO CENTER CHANNEL, PLACE POWER PACK IN TRAY
(FOR PLUGGING IN POWER CORDS, REFER TO ADJUSTABLE BASE DESK INSTRUCTIONS).
10. PLUG IN MOTOR & CONTROL UNIT INTO POWER PACK CORD INTO AC OUTLET.
11. IF DISASSEMBLY IS REQUIRED, LOWER ADJUSTABLE DESK BASE TO THE LOWEST POINT.
POWER
CORD
ADJUSTABLE DESK BASE
(SOLD SEPARATELY)
FOR ADJUSTING BASE WIDTH READ ASSEMBLY
INSTRUCTIONS PROVIDED WITH ADJUSTABLE DESK BASE
ADJUSTABLE LEVELERS
F
E
HARDWOOD CORNER BLOCK
HARDWOOD
CORNER BLOCK
THREADED INSERT PANELS
74-1
DESK TOP
(TOP VIEW)
DESK TOP CUT OUT TO
SHOW WHERE TO ATTACH
POWER PACK SUPPORT TRAY
ATTACH METAL POWER PACK TRAY
TO CENTER CHANNEL.
PLACE POWER PACK IN TRAY AND PLUG IN MOTOR AND CONTROL UNIT
(REFER TO ADJUSTABLE DESK BASE INSTRUCTIONS)
POWER PACK
SUPPORT TRAY
AFTER ROTATING DESK TO IT'S UPRIGHT POSITION,
ATTACH METAL POWER PACK TRAY
/