AGPtek DC2R User manual

Category
Pet care
Type
User manual

AGPtek DC2R is a remote training system suitable for dogs. It allows you to control your pet using various methods, such as vibration, shock, light, and beep. You can choose the intensity of the stimulation to match your dog's personality and training needs. The device has a range of 300 meters, so it is suitable for both indoor and outdoor use. To get started, you need to match the collar with the remote controller, which is a simple process that is explained in the user manual.

AGPtek DC2R is a remote training system suitable for dogs. It allows you to control your pet using various methods, such as vibration, shock, light, and beep. You can choose the intensity of the stimulation to match your dog's personality and training needs. The device has a range of 300 meters, so it is suitable for both indoor and outdoor use. To get started, you need to match the collar with the remote controller, which is a simple process that is explained in the user manual.

DC2R Remote Training System With LCD display and of 300 meters range
Controller
Features :
1.100 levels of vibration.
2.100 levels of shock(optional).
3.The levels can be altered by use of up & down button.
4.A tone button activates a tone on the receiver collar.
5.The system can be used for 1 or 2 receivers’ collars.
6.Four modes --shock, vibration, light and beep mode, meet your different training needs.
7.300 meters usage range in open areas.
8.Power saving design: the controller enters sleep mode after 20s of no operation, and wakes up by
pressing MODE for 1s; the receiver enters sleep mode after 20s no movement, and wakes up when
moving.
Getting charge
1. Charge the controller
Connect the charger connector to the charging jack. After plugging the charger into a standard
outlet the red LED light inside the transmitter will be lighted. Charge the controller at least 6 hours for the
first charge. After fully charged, the red LED light will be turned off automatically.
2. Charge the receiver collar
After plugging the charger into a standard outlet, the red LED light inside the receiver collar will be lighted.
Charge the receiver collar at least 6 hours for the first charge. After fully charged, the red LED light will be
turned off automatically.
How to match
1. Please press the MODE button of controller for 5-10s, then the controller will be turned on. Press the
CHANNEL button and select CHANNEL1 (the small icon can be seen at the upper right of the
LED screen).
2. Press the reset button with a needle for 5s within 20 seconds (the Controller is in the ready state after it
has been started)).While finishing installing the battery, you will hear a sound “beep.
3. Then press the Y button of controller immediately and you can hear a beep again. That shows the
item is paired successfully. If not, please remove the batteries of collar and install them once again, and
try the above steps.
Matching the second collar
If you have another collar, please follow the next steps to finish matching.
1. Please press the MODE button of controller for 5-10s, then the controller will be turned on. Press the
CHANEL button and select CHANNEL 2 (the small icon can be seen at the upper right of the LED
screen).
2. Press the reset button with a needle for 5s within 20 seconds. While finishing installing the battery, you
will hear a sound beep.
3. Then press the Y button of controller immediately and you can hear a beep again. That shows the
item is paired successfully. If not, please remove the batteries of receiver collar and install them once
again, and try the above steps.
Note: CHANNEL 1 and CHANNEL 2 are in no order, so you can set any collar to any CHANNEL
according to you custom.
Intensity Regulation
The shock and vibration function can be set from 0 to 100 by pressing the UP/DOWN buttons on right
hand side. When using shock or vibration, you can choose intensity levels according to your needs.
Using The Four Models (after encoding is completed)
Four modes can be altered by pressing the MODE button of controller.
1. Shock Model
Test the static shock function
1) Take out the test bulb from the package and put it on the Receiver collars contact points.
(2) Press MODE button of controller, switch to Shock Mode (the small icon can be seen at the upper
left of the LED screen). Press UP/DOWN button on the right side confirming LCD display is not to be 0.
(3) Press Y button and observe the change of test bulb. You can see flash light in the middle of test bulb
that means the shock function works.
Use the shock function
(1) When using the shock function, you need to install the receivers contact column. According to the size
of the dog and dog hair length, choose the right column for your dog between the tall one and short one.
(2) Thread the collar strap through the slots on the receiver, and tie it to the dog.
2. Vibration Model
(1) Press Mode button of controller, switch to Vibrate Mode (the small icon can be seen at the upper
part of the LED screen). Press UP/DOWN button on the right side confirming LCD display is not to be 0.
(2) Press Y button, Receiver collar will vibrate, that means Vibration function works.
3. Beep Model
(1) Press Mode button of Controller, switch to Beep Mode (the small icon can be seen at the upper
part of the LED screen).
(2) Press the Y button and receive collar will beep, that mean Beep Function works.
4. LED Light Model
(1) Press Mode button of Controller, switch to LED light Mode (the small icon can be seen at the
upper right of the LED screen).
(2) Press the Y button and then the receiver collar and the indicator light of controller will flash at the same
time, signifying that the LED Light function works.
Package includes
1 x remote control
1 x collar
1 x charger cord
1 x test light&probes
1 x Maual
Notes for Function:
1. The lifetime of the batteries vary according as how often you use the product. Therefore you should
often check batteries when the receiver collar makes sound beep beep and the right down side of LCD
screen shows up the symbol .
2.The valid distance of Controller means the straight-line distance between the Controller and the
Receiver Collar without obstacles in between. If there are interference signals or signal screening around,
the actual remote Controller distance may vary.
3.If you hear a little ratting sound inside the collar, dont worry. It is the Touch switch used to wake up the
collar when in sleep mode.
Training Tips
1. Before you use the training collar, read the instructions carefully and learn to use it. Make sure both
function are OK and then attach the receiver collar to your dogs neck.
2. Practice using the electronic remote training collar.
Start at the lowest level of stimulation and observe your dog when you activate it. The dog's ear might
twitch or he may move his head as if trying to get away from the collar. If your dog doesn't respond at the
lowest stimulation, slowly turn the transmitter to the next level and try again.
3. Reinforce commands your dog understands.
When you train your dog with an electronic collar, begin with commands the dog is familiar with.
Say the command, such as sit or stay, and wait for your dog to respond. If your dog is not paying
attention, press the button on your transmitter and repeat the command.
Praise your dog as soon as he responds.
Reward your dog with a pat, by saying "good dog," or with a special treat. When you train dogs, you
want to reinforce their good behavior with a reward.
5. Control bad behavior.
Plan for bad behavior. For instance, if your dog digs holes in the backyard whenever you let him
outside, be ready to use an electronic collar to train him when you let him out.
Don't let your dog see you. You don't want your dog to know you are causing the unpleasant
sensation around his neck when he starts digging. Rather, you want him to associate the sensation
with the bad behavior.
Set the stimulation on the transmitter to a low level, and if that is not effective, turn it up again. You
want to get the dog's attention without hurting him.
When the dog begins to dig, or engage in whatever behavior you want to control, activate the
transmitter. Do not hold the button down for more than 3 seconds and do not punch it repeatedly. The
object is to train your dog, not injure him.
Notes of training
1. Don't leave an electronic remote training collar on your dog for more than 12 hours at a time because it
may irritate the dog's neck.
2.This product is for pet training. Only by training, the pet can understand the intention of its owner.
Good effect can only be achieved after a period of training.
3.Training sessions should be kept positive and short, about 10-15 minutes long each time.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

AGPtek DC2R User manual

Category
Pet care
Type
User manual

AGPtek DC2R is a remote training system suitable for dogs. It allows you to control your pet using various methods, such as vibration, shock, light, and beep. You can choose the intensity of the stimulation to match your dog's personality and training needs. The device has a range of 300 meters, so it is suitable for both indoor and outdoor use. To get started, you need to match the collar with the remote controller, which is a simple process that is explained in the user manual.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI