DMP Electronics 1100X Installation guide

Brand: DMP Electronics

Model: 1100X

Category: Security access control systems

Type: Installation guide

DMP Electronics 1100X is a Wireless Receiver compatible with all DMP wireless devices. It provides two-way, supervised communication using 900 MHz frequency hopping-spread-spectrum technology and can be mounted up to 1,000 feet from the panel enclosure, providing up to 500 wireless zones. The 1100X Wireless Receiver is typically mounted at a distance not to exceed 1000 feet away from the panel enclosure. A location should be selected that is centrally located between the 1100 Series transmitters used in the installation.

InstallatIon GuIde

1100X Wireless Receivers

Description

The 1100X Wireless Receiver is compatible with all DMP wireless devices. The receiver provides two-way, supervised

communication using 900 MHz frequency hopping-spread-spectrum technology. The receiver can be mounted up to

1,000 feet from the panel enclosure. The receiver provides up to 500 wireless zones. Refer to the panel installation

guide for number of available wireless zones.

Compatibility

• XR500SeriespanelsusingrmwareVersion113orhigher

• XR100 Series panels

• XR150/XR350/XR550Seriespanels

What is Included

The receiver includes the following items:

• OneModel1100XWirelessReceiver

• One4-wireHarness

• Hardwarepack

Compliance Instructions

ForapplicationsthatmustconformtoaNationalRecognizedTestingLaboratorycerticatedsystem,pleaseseethe

ListedComplianceSpecicationssectionattheendofthisguideforadditionalinstructions.

Installing the Wireless Receiver

Selecting a Location

Choose an optimum location to mount the receiver. The 1100X Wireless Receiver is typically mounted at a distance

not to exceed 1000 feet away from the panel enclosure. A location should be selected that is centrally located

between the 1100 Series transmitters used in the installation. Install the receiver away from large metal objects.

Mounting the receiver on or near metal surfaces impairs performance. Do not use shielded wire between the panel

andreceiver.Whenselectingthepropermountinglocationofatransmitter,refertotheLEDSurveyOperation

sectionofthespecicinstallationguideforthetransmitterbeinginstalled.

Tamper Switches

The 1100X is equipped with a case tamper and a wall tamper.

Mounting the Receiver

1. Remove the cover from the plastic housing by

squeezing both sides toward each other.

2. Secure the receiver to the wall in the desired

location installing the supplied shoulder

washers and screws in the mounting hole

locations as shown in Figure 1.

3.Snapthecoverbackontheunit.Thepanel

immediately recognizes the 1100X Receiver if

the panel is programmed with a house code.

RED

PROG

PANEL

RED

Power

RXD

TXD

Status

RF RXD

RF TXD

Mounting Hole

Locations

Squeeze to

Remove Cover

Squeeze to

Remove Cover

J4 Not Used

J3 Connects

To Panel

Mounting Screw

Shoulder Washer

Power

Panel Receive

Panel Transmit

Status

RF Receive

RF Transmit

LEDs

Tamper

Switch

Figure 1: Receiver PCB

Digital Monitoring Products 1100X Wireless Receiver Installation Guide

Wireless Bus Connection

The 1100X easily interfaces with the XR500/XR500FC and XR100/XR100FC Series panels using the on-board DMP

Wireless Bus connection (J22).

OnXR150/XR350/XR550Seriespanels,the1100Xinterfacesusingtheon-boardX-Busconnection(J13).

Note: The 1100X Wireless Receiver cannot operate if connected to the Keypad Bus.

Harness Connection XR100/XR100FC/XR500/XR500FC panels

1.Installajumperacrosstheheaderpinsnexttotheletter“X”ontheXR100/XR100FC/XR500/XR500FCpanelJ23

header to enable on-board DMP Wireless operation.

2.Usingthesupplied4-wireharness,connectfromtheJ3headeronthe1100XWirelessReceivertotheXR100/

XR100FC/XR500/XR500FC panel J22 LX header.

3.Afterpower-up,brieyresetthepanelusingtheJ16jumpertoactivatezoneoperation.

4.InSystemOptions,programtheHouseCode(1-50).InZoneInformation,programthewirelesszones.

Figure 3: XR100/XR100FC or XR500/XR500FC DMP Wireless Bus Connection

Harness Connection XR150/XR350/XR550 panels

1.ConnecttheJ3headeronthe1100XtotheXR150/XR350/XR550panelJ13X-BUSheader.

2.Afterpower-up,brieyresetthepanelusingtheJ16jumpertoactivatewirelesszoneoperation.

3.InSystemOptions,programtheHouseCode(1-50).InZoneInformation,programthewirelesszones.

Figure 4: XR150/XR350/XR550 DMP Wireless Bus Connection

RED

PROG

PANEL

RED

Power

RXD

TXD

Status

RF RXD

RF TXD

1234 5678 10 11 12 13 14 15 169

+B BELL GND SMK GNDRED YEL GRN BLKZ1Z2Z3AC –B GND G

K6 K7

Output 1 Output 2

J10

J22

Battery

Start

J23

J21

RS-232

Power

LED

PROG

Out1 Out2

XR100/XR100FC/XR500/XR500FC

Series Panel

Black

Green

Yellow

Red

Can be extended

up to 1000 feet

from the panel

Red

1100X

Receiver

J4 Not Used

XMT - Transmit LED

REC - Receive LED

Black

Green

Yellow

Red

Can be extended

up to 100 feet

from the panel

using 22 AWG

or 250 feet

using 18 AWG

XR150/XR350/XR550

Series Panel

Battery Start

Power

LED

RED

PROG

PANEL

RED

Power

RXD

TXD

Status

RF RXD

RF TXD

1100X

Receiver

J4 Not Used

REC - Receive LED

XMT - Transmit LED

1100X Wireless Receiver Installation Guide Digital Monitoring Products

1100X Receiver Operation

The 1100X receiver automatically sends the panel house code to wireless transmitters when the unique transmitter serial

numberisprogrammedintothepanel.Thehousecodeidentiesthepanel,receiver,andtransmitterstoeachother.The

receiveronlylistensfortransmissionsusingthespeciedhousecodeand/orprogrammedtransmitterserialnumber.

Note: When setting up a wireless system, it is recommended to program zones and connect the receiver before

installing batteries in the transmitters.

Transmitters can be programmed for supervised operation. When programmed as supervised, the transmitter must

communicate with the receiver within the programmed number of minutes. If the transmitter fails to communicate, the

panel displays a missing condition.

Note: When a receiver is installed, powered up, or the panel is reset, the supervision time for transmitters is reset. If the

receiverhasbeenpowereddownformorethanonehour,wirelesstransmittersmaytakeuptoanadditionalhourtosend

a supervision message unless tripped, tampered, or powered up. This operation extends battery life for transmitters. A

missingmessagemaydisplayonthekeypaduntilthetransmittersendsasupervisionmessage.

When any wireless zone programming is changed in the panel, receiver zone programming is updated. At that point, all

wireless zones display as normal for approximately one minute, regardless of the actual state of the contact.

1100X LED Operation

Six LEDs display receiver operation and activity. Refer to the table below as required.

PCB LEDs Label Operation

Power

RXD

TXD

Status

RF RXD

RF TXD

POWER Steady green to indicate there is power to the receiver.

RXD Flashes yellow to indicate data is being received from the panel.

TXD Flashes green to indicate data is being sent to the panel.

STATUS Steadyredtoindicatememoryupload.Offwhenuploadiscomplete.

RF RXD Flashes yellow to indicate data is being received from a transmitter.

RF TXD Flashes green to indicate data is being sent to a transmitter.

Transmitter Survey LED Operation

DMP1100SeriestransmittersprovideTwo-way(transmitacknowledge)operation.Thisadvanceddataprotocolallowseach

transmittertoconrmthateachofitsmessages(alarm,checkin,tamper,lowbattery)arereceivedandacknowledged

bythe1100Seriesreceiver.TheconrmationisindicatedvisuallybyuseofanLEDoneachtransmitter.ThisSurveyLED

shouldbeusedduringinstallationtotesteachtransmitterforproperoperation.AfulldenitionoftheSurveyLEDfollows.

TheredLEDonan1100Seriestransmitterturnsonwhentheprocessorwakesuptosendamessage.Thenafteraseries

of communication steps are completed (successful or not),theLEDturnsoffwhentheprocessorgoesbacktosleep.99.9%

of the time the processor is asleep in normal operation. The following list summarizes various indications that can be

observedontheLEDandadenitionforeach.Notethisisforasinglemessage.Example,pressingandholdingthetamper

switch.

Single 1/16 second ash

•Processorwakesup

•Transmitterreceivesimmediatesynchronizationfromreceiver

•Transmittertransmits

•Transmitterreceivesimmediateacknowledgementfromreceiver

•Processorgoestosleep

Single Pulse greater than 1/16 second but shorter than 8 seconds

•Processorwakesup

•Transmitterreceivessynchronizationfromreceiver-possiblynotimmediate

•Transmittertransmits

•Transmitterreceivesacknowledgementfromreceiver-possiblynotimmediate

•Processorgoestosleep

Steady for 8 seconds

•Processorwakesup

•Transmitterneverreceivessynchronizationfromreceiver,ormightreceivesynchronization

•Transmittertransmitsifsynchronizationwasreceived

•Transmitterneverreceivesanyfurtherdatafromreceiver

•Processortimesoutandgoestosleep

Multiple short ashes

•Processorwakesup

•Transmitterreceivessynchronizationfromreceiver

•Transmittertransmits

•Transmitterreceivesdatafromreceiver,butnotavalidacknowledgement

•Processorbrieygoestosleep

•Entiresequenceisrepeated,eachshortashindicatesacycle

Digital Monitoring Products 1100X Wireless Receiver Installation Guide

Troubleshooting Using the Transmitter Survey LED

If a transmitter is unable to reliably communicate a message to the receiver, or is reported as missing, the Survey LED can

be used to help diagnose the issue. If the missing transmitter cannot be explained by obvious reasons such as a damaged

transmitter, failed battery, or changes in building construction; then the Survey LED should be used.

TousetheSurveyLEDoperationtohelpdiagnoseaeldissue,completethefollowingstepsonan1100Seriestransmitter.

Repeat the following sequence 5 times and write down the LED operation for each tamper switch action.

•Pressandholdthetamperswitch

•ObservetheLEDuntilitturnsoffforatleast5seconds

•Releasethetamperswitch

•ObservetheLEDuntilitturnsoffforatleast5seconds

You now have observed the LED 10 times. Based on the results you have recorded use the list below to assist in

troubleshooting.

LED turns on a single time for less than 1 second 8 to 10 times.

•Systemisworkingproperly

LED turns on for more than 1 second 3 to 9 times.

•Thetransmitterorreceiverneedstoberelocated

LED turns on for more than 1 second all 10 times.

•Thereceiverisnotturnedon,orisnotoperating

•Thetransmitterisnotprogrammedintothereceiver

•Thetransmitterorreceiverneedstoberelocated

LED ashes multiple times with a single tamper press or release 3 to 10 times.

•Thetransmitterorreceiverneedstoberelocated

LED never turns on.

•Thetransmitterbatteryisdead

•Thetamperswitchisbeingpressedorreleasedtooquickly

•Thetamperswitchorotherpartofthetransmitterisbroken

LED stays on constantly and is dim

•Thetransmitterbatteryisalmostdead

•Thetransmitterisbroken

General Wireless Troubleshooting

IfALLwirelessdevicesdonotoperate,refertothefollowingchecklist:

• Verifythereceiverisan1100XandthepanelisanXR500SerieswithrmwareVersion113orhigheroranXR100/

XR100FC/XR500FC,orXR150/XR350/XR550Seriespanel.

 VerifytheXR100/XR100FC/XR500/XR500FCpanelJ23jumperisinthe“X”positionandthe4-wireJ3connectorfrom

the receiver is connected to J22 of the panel.

 VerifytheJ3connectorfromthereceiverisconnectedtoJ13ontheXR150/XR350/XR550panel.

• BrieyresetpanelusingJ16jumpertoactivatewirelessoperationandwaitoneminutetotestwirelesszone(s).

• VerifytheHouseCode(1-50)isprogrammedinSystemOptions.

• Verifyappropriatezonenumbersareassignedaswirelesszones.

• VerifythatthepanelXMITandRECLEDsalternatelyashonandoffatarateof1/4secondeach.IftheLEDsareOn

steadyorOff,thepanelandreceiverarenotcommunicatingproperly.(SeeFigure3and4).

• Verifythe1100XLEDsoperatecorrectlyaslistedin1100XLEDOperation.

• Verifytransmittershavebatteriescorrectlyinserted.

1100X Wireless Receiver Installation Guide Digital Monitoring Products

Transmitter Supervision Time

For UL Listed installations, program the transmitter supervision time in panel zone programming as listed in the following

table.RefertotheXR500SeriesProgrammingGuide(LT-0679)orXR100SeriesProgrammingGuide(LT-0896)forcomplete

wireless programming information.

UL Listing Listed Accessories

Supervision

Time

UL 1023 HouseholdBurglaryAlarmSystemUnitsAccessory 1100R Repeater

1101/1102/1103/1105Universal

Transmitters

1125/1127W/1127CPIRMotionDetector

1135WirelessSounder

1142Two-ButtonHold-UpTransmitter

9060/9063WirelessKeypad

UL 636 HoldupAlarmUnitsandSystemsAccessory 1142Two-ButtonHold-UpTransmitter 60

UL 634 ConnectionsandSwitchesforusewithBurglarAlarm

Systems Accessory

1100R Repeater

1101/1102/1103/1105Universal

Transmitters

UL 639 IntrusionDetectionUnitsAccessory 1100R Repeater

1125/1127W/1127CPIRMotionDetector

UL 365 PoliceStationConnectedBurglarAccessory 1100R Repeater

1103UniversalTransmitter

UL 609 LocalBurglarAlarmUnitsandSystemAccessory 1100R Repeater

1103UniversalTransmitter

UL 1076 ProprietaryBurglarAlarmUnitsAccessory 1100R Repeater

1103UniversalTransmitter

UL 1610 CentralStationBurglarAlarmUnitsAccessory 1100R Repeater

1103UniversalTransmitter

1135WirelessSounder

9060/9063WirelessKeypad

UL 268 Smoke-AutomaticFireDetectors 1100R Repeater

1161/1162ResidentialSmokeDetectors

1165/1166/1167CommercialSmoke

Detectors

UL 346 WaterowIndicatorsforFireProtectiveSignalingSystems 1100R Repeater

1181PIV/1182OS&Y

UL 521 Heat Detectors for Fire Protective Signaling Systems 1100R Repeater

1183-135F/1183-135RHeatDetector

UL 985 HouseholdFireWarningSystemAccessory 1100R Repeater

1135WirelessSounder

9060/9063WirelessKeypad

240

UL 864 FireProtectiveSignalingSystems 1103UniversalTransmitter

1100R Repeater

UL 2075 GasandVaporDetectorsandSensors 1184WirelessCarbonMonoxideDetector 240

FCC Information

ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Changesormodicationsmadebytheuserandnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidthe

user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

Note: The 1100 Series wireless system is a two-way supervised wireless design compliant with FCC rules as they pertain to 900

MHz Spread Spectrum devices. In rare instances it has been observed that certain 900 MHz cordless telephones may occasionally

experienceaclickingsoundonthetelephonewhileinuse.Ifthisoccurs,itmayberesolvedbyselectingadifferentchannelon

the cordless telephone, or replacing the cordless phone with a different brand or model of 900 MHz telephone or other cordless

telephone.

To comply with RF exposure requirements, a minimum distance of 20cm must be maintained between the antenna and all persons.

800-641-4282

www.dmp.com

Designed, Engineered and

Assembled in U.S.A.

INTRUSION • FIRE • ACCESS • NETWORKS

2500 North Partnership Boulevard

Springfield, Missouri 65803-8877

13285

Listings and Approvals

California State Fire Marshal (CSFM)

FCC Part 15: CCK1100

NewYorkCity1100SeriesWireless(FDNYCOA#6145)

IndustryCanada:5251A-PC0082

Underwriters Laboratories (UL) Listed

ANSI/UL365 PoliceStationConnectedBurglar

ANSI/UL609 LocalBurglarAlarmUnitsandSystems

ANSI/UL634 ConnectionsandSwitchesforusewith 

Burglar Alarm Systems Accessory

ANSI/UL636 HoldupAlarmUnitsandSystem

ANSI/UL639 IntrusionDetectionUnitsAccessory

ANSI/UL1023 HouseholdBurglarAlarmSystemUnits

ANSI/UL1076 ProprietaryBurglarAlarmUnits

ANSI/UL1610 CentralStationBurglarAlarmUnits

ANSI/UL864 FireProtectiveSignalingSystems

ANSI/UL985 HouseholdFireWarningSystem

Specications

OperatingVoltage 8.0to14VDC

CurrentDraw  46mA

RFPowerRating 27mW

FrequencyRange  903-927MHz

Dimensions

ReceiverHousing 4.65”Lx3.1”Wx1.4”H

Antennas  8.6”H

Color White

Housing Material Flame retardant ABS

Patents

U.S.PatentNo.7,239,236

Attention! Older Cordless Telephones

Yourwirelessalarmsystemiscomprisedofastate-of-the-arttwo-waysecurenetworkcreatedbysophisticatedtransmittersand

receivers. It is compliant with all FCC rules as they pertain to 900 MHz Spread Spectrum devices which require devices to share the same

frequencies. This creates a possibility of interference with other devices in your home.

Ithasbeenreportedthatcertainolder900MHzcordlesstelephonesmayonrareoccasionsexperienceinterference(anaudibleclicking

sound)whileinuse.(Thismayalsooccurwithsome2.4GHzand5.8GHztelephonesasmanystilluse900MHzfrequencies).Ifthis

occurs on your cordless telephone, it may be resolved by selecting a different channel on your telephone. If your telephone does not

havethisselection,itcanalsoberesolvedbyreplacingyouroldcordlesstelephonewithaDECT6.0cordlesstelephone.

What is DECT 6.0?

DECT6.0(DigitalEnhancedCordlessTelecommunications)isthecurrentstandardforcordlesstelephones,anditprovidesseveralbenets

over900MHz,2.4GHzand5.8GHzsystems.

• NoMoreInterference-unlikeoldercordlesstechnology,DECT6.0telephonesarevirtuallyimmunetohouseholdinterference,

 andviceversa.Ifyouhaveawirelesscomputernetworkinyourhome,DECT6.0won’tdisruptinternetuse.

• EncryptedPrivacy–DECT6.0hasalayerofsecuritythatoldercordlesstelephonesjustdon’thave.Asinformationandidentity

 theftisontherise,DECTencryptionhelpskeepyourpersonalcommunicationssafe.

• CallQuality-Extrasecurityisn’tjustforsafety;itgivesyouclearercallswithoutcrossovertrafc.

• BatteryLife-ADECT6.0phonewilllastasmuchas30%longerthana5.8GHzphone.

More information can be found on DECT technology at www.DECT.org.

DECT6.0Cordlessphonescanbefoundatanymajorretailerincluding:Wal-Mart™,Target™,BestBuy™&RadioShack™.

Listed Compliance Specications

Commercial Fire

Transmitters must be programmed as supervised. Refer to the Transmitter Supervision Time table for the supervision

time.

Themaximumlineimpedanceofthe4-wirebusis16.2Ohmsfor1000feet.

The recommended wire gauge for panel to receiver connection is 22 AWG.

Afteralltransmittersareinposition,theWLSoptionofthepanel’sWalkTestmustbeoperatedandalltransmitters

programmedforFire(FI)orSupervisory(SV)mustshowthattheircheckinmessagewasreceived.Refertothepanel

programmingguideforTripCounterforDMPWirelesscheck-inTest(WLS)whichdescribesthatbothnumbersofthe

counter must match. If not and a failed wireless zone is displayed at END, decrease that transmitters range with the

receiverandperformtheWLSWalkTestagain.

DMP Electronics 1100X Installation guide

Brand: DMP Electronics

Model: 1100X

Category: Security access control systems

Type: Installation guide

Download PDF

report

DMP Electronics 1100X Installation guide

DMP Electronics 1100X Installation guide

Related papers

Other documents