Malaguti Password 250 i.e. Workshop Manual

FRAME AND RUNNING GEAR

WORKSHOP MANUAL

3

11/06

A

PASSWORD 250 i.e.

TABLE OF CONTENTS

1

FRAME AND RUNNING GEAR

1 - INTRODUCTION

Manual updates................................................................ 6

NOTES FOR EASY CONSULTATION ...................... 6

Configuration of the pages ............................................... 6

Modified pages ................................................................. 6

Additional pages .............................................................. 6

Symbols ............................................................................ 7

Abbreviations.................................................................... 7

Units of measurement ...................................................... 7

GENERAL WORK PROCEDURES .......................... 8

Suggestions...................................................................... 8

Recommendations ........................................................... 8

OPERATING SYMBOLS ......................................... 10

2 - GETTING TO KNOW

YOUR SCOOTER

TECHNICAL DATA ................................................... 11

Dimensions....................................................................... 11

Capacities......................................................................... 11

Engine .............................................................................. 11

Spark plug ........................................................................ 11

Transmission .................................................................... 11

Fuel system....................................................................... 11

Ignition .............................................................................. 11

Brakes............................................................................... 11

Frame ................................................................................ 11

Suspension....................................................................... 11

Battery............................................................................... 11

Tyres ................................................................................. 11

IDENTIFICATION OF MAIN COMPONENTS

(left-hand side) ....................................................... 12

IDENTIFICATION OF MAIN

COMPONENTS (right-hand side) ........................... 12

IDENTIFICATION DATA:

FRAME N° / ENGINE N°.......................................... 13

TYRES .................................................................... 14

Inflation pressure .............................................................. 14

FUEL TANK ............................................................. 15

COOLANT TANK ..................................................... 16

REAR-VIEW MIRRORS ........................................... 16

HELMET COMPARTMENT...................................... 17

GLOVE COMPARTMENT ........................................ 18

INSTRUMENT PANEL............................................. 19

DIGITAL INSTRUMENT PANEL .............................. 20

FUNCTION SELECTION AND WARNING

OR ALARM SIGNALS ............................................. 21

Secondary menu or submenu .......................................... 21

Main menu........................................................................ 23

Bar graph .......................................................................... 23

Alarms function ................................................................. 24

MILES OR KILOMETRES SELECTION.................. 25

HANDLEBAR CONTROLS ...................................... 25

Right-hand control............................................................ 26

Left-hand control .............................................................. 26

KEYSWITCH ........................................................... 27

HANDLEBAR LOCK ................................................ 27

Locking ............................................................................. 27

Unlocking.......................................................................... 27

STANDS .................................................................. 28

Centre stand ..................................................................... 28

Side stand......................................................................... 28

OWNER’S TOOLKIT ................................................ 29

DIMENSIONAL CHECK OF FRAME ....................... 30

3 - INSTRUCTIONS FOR USE

STARTING THE ENGINE

................................... 31

4 - MAINTENANCE

INTRODUCTION ...................................................... 32

Warnings .......................................................................... 32

MAINTENANCE TABLE........................................... 32

TRANSMISSION OIL .............................................. 33

Level check....................................................................... 33

ENGINE OIL ............................................................ 34

Engine oil level check ...................................................... 34

Oil top-up .......................................................................... 35

FRONT/REAR BRAKE FLUID ................................. 36

COOLANT ............................................................... 36

Coolant temperature indicator ......................................... 37

LUBRICANT TABLE ................................................ 37

SPARK PLUG.......................................................... 38

ADJUSTING

THE REAR SHOCK-ABSORBERS .......................... 39

ADJUSTING IDLING SPEED .................................. 39

THROTTLE PLAY ADJUSTMENT ........................... 39

ADJUSTING THE BRAKE LEVERS ........................ 39

CHECKING THE PADS AND DISCS OF THE

FRONT/REAR BRAKES (condition and wear) ....... 40

HEADLIGHT ............................................................ 41

Adjusting the beam........................................................... 41

Replacing the headlight bulbs ......................................... 41

4

11/06

A

PASSWORD 250 i.e.

FRAME AND RUNNING GEAR

TABLE OF CONTENTS

1

FRONT TURN INDICATOR....................................... 42

Changing the front turn indicator bulb ............................. 43

TAILLIGHT (with brake light) ................................. 43

Replacing the taillight bulbs............................................. 44

NUMBER PLATE LIGHT ......................................... 45

Replacing the number plate light bulb ............................. 45

FUSES .................................................................... 46

BATTERY (12V - 12AH) ........................................... 47

Installing the battery ......................................................... 47

Removing the battery ....................................................... 48

Recharging the battery ..................................................... 48

5 - DISASSEMBLY

INSTRUMENT PANEL WINDSHIELD ...................... 49

UPPER HANDLEBAR COVER ................................ 49

INSTRUMENT PANEL ............................................. 50

ACCESSIBILITY...................................................... 51

AMBIENT TEMPERATURE SENSOR ..................... 52

RIGHT-HAND CONTROL ......................................... 52

LEFT-HAND CONTROL ........................................... 53

FRONT FAIRING ..................................................... 53

ACCESSIBILITY...................................................... 54

HEADLIGHTS.......................................................... 55

GRILLE ................................................................... 55

FRONT MUDGUARD ............................................... 56

SPEEDOMETER SENSOR ..................................... 57

FRONT BRAKE CALIPER ....................................... 57

CHECKING FRONT BRAKE WEAR ......................... 58

REPLACING THE FRONT CALIPER ....................... 58

FRONT WHEEL ....................................................... 59

FRONT BRAKE DISC .............................................. 60

LEFT AND RIGHT HALF SHIELD ........................... 61

ACCESSIBILITY...................................................... 63

HORN ...................................................................... 64

RIGHT AND LEFT

LATERAL SUB PANELS ......................................... 65

ACCESSIBILITY...................................................... 66

VOLTAGE REGULATOR .......................................... 67

“CDI” CONTROL UNIT........................................... 67

BATTERY COMPARTMENT TUNNEL COVER ........ 68

RIGHT SIDE ACCESSIBILITY ................................ 69

LEFT SIDE ACCESSIBILITY .................................. 69

BATTERY ................................................................ 70

SUB-FAIRING .......................................................... 71

LOWER FAIRING..................................................... 72

FOOTBOARD ........................................................... 75

COOLANT EXPANSION TANK ................................ 76

SIDE STAND ........................................................... 77

Side stand switch.............................................................. 77

CENTRE STAND ..................................................... 78

MAIN ELECTRICAL SYSTEM ................................ 79

RADIATOR............................................................... 80

FAN UNIT ................................................................ 83

RADIATOR (assembly) ............................................ 83

KEYSWITCH ........................................................... 84

SEAT ....................................................................... 85

HELMET COMPARTMENT...................................... 85

SEAT LOCK ............................................................ 85

ACCESSIBILITY...................................................... 87

THROTTLE BODY AND ASPIRATION

CONNECTOR .......................................................... 88

FUEL LEVEL SENSOR........................................... 89

FUEL PUMP ............................................................ 89

PILLION GRAB HANDLE ........................................ 90

TAILLIGHT .............................................................. 91

ACCESSIBILITY...................................................... 91

TAILLIGHT (assembly) ........................................... 92

NUMBER PLATE LIGHT ......................................... 93

REAR FAIRING ....................................................... 94

ACCESSIBILITY...................................................... 95

FUEL TANK ............................................................. 96

SILENCER .............................................................. 98

LAMBDA PROBE AND DISCHARGE COLLECTOR 99

DISCHARGE COLLECTORS ................................... 99

REAR SHOCK ABSORBERS .................................. 100

REAR MUDGUARD .................................................. 101

REAR BRAKE CALIPER ......................................... 102

CHECKING THE REAR

BRAKE PADS FOR WEAR ...................................... 102

REPLACING THE REAR CALIPER ......................... 102

REAR WHEEL ......................................................... 103

ASSEMBLY OF REAR WHEEL ............................... 104

REAR DISC ............................................................. 105

NUMBER PLATE HOLDER REAR FAIRING............ 105

FILTER BOX ............................................................ 106

5

11/06

A

PASSWORD 250 i.e.

FRAME AND RUNNING GEAR

TABLE OF CONTENTS

1

PILLION FOOTREST .............................................. 109

ENGINE ................................................................... 110

BRAKE MASTER CYLINDERS ............................... 113

HANDLEBAR ........................................................... 114

FRONT FORK .......................................................... 115

FRONT DAMPER..................................................... 116

Right ................................................................................. 116

Left .................................................................................... 116

Checking the oil level in the damper................................ 117

Changing the fork oil ........................................................ 118

BRAKE CALIPERS ................................................. 119

Removing the front caliper ............................................... 119

Changing the front caliper................................................ 119

Overhaul ........................................................................... 120

Removing the rear caliper................................................ 120

Replacing the rear caliper................................................ 120

Rear caliper disassembly................................................. 120

BRAKE SYSTEM .................................................... 123

BLEEDING THE BRAKE SYSTEM ......................... 124

Front caliper ...................................................................... 124

Rear caliper ...................................................................... 124

6

11/06

A

PASSWORD 250 i.e.

FRAME AND RUNNING GEAR

TABLE OF CONTENTS

1

INTRODUCTION

• This Workshop Manual describes the main electrical/mechanical checks, the essential checks and the assembly of

components supplied disassembled in order to deliver a brand new vehicle (the sequence of operations is not

binding).

• It is essential to follow the instructions with great care. Work carried out carelessly or, worse still, work that has not

been accomplished, can cause injuries and damage or, in the less serious cases, complaints.

NOTE These manuals provide the necessary information and instructions for routine maintenance and serv-

icing.

Some information has been given to us by the engine manufacturers. We therefore decline all respon-

sibility for any error, omission or misrepresentation.

MALAGUTI reserves the right to make any changes and modifications hereto it deems necessary

without prior notice.

MANUAL UPDATES

• The updates will be sent by us (in a reasonable time). Every CD-Rom you receive will supersede the one already in

your possession.

• The table of contents will be duly updated in the event that new pages are inserted, which render the consultation

of the manual difficult.

• IMPORTANT! The Workshop Manuals are to be considered as essential tools to be properly kept up-to-date so as

to maintain their validity over time.

Y

X

W

Z

A

YX

WW

Z

NOTES FOR EASY CONSULTATION

CONFIGURATION OF THE PAGES

MODIFIED PAGES

• Pages that have been modified will bear the same number as the same page of the previous edition, followed by a

letter M and, in the relative box, the new date of issue.

ADDITIONAL PAGES

• Any additional pages shall bear the last number of the section to which they belong, followed by the letter A and the

new edition date.

Chapter

Section title

Page N°

Date of issue

INTRODUCTION

7

11/06

A

PASSWORD 250 i.e.

FRAME AND RUNNING GEAR

TABLE OF CONTENTS

1

F

Cs

P

Pr

S

Sc

T

V

SYMBOLS

• Symbols are provided for quick and easy reference (see the relevant heading), identifying situations requiring

utmost attention or providing practical suggestions or simple information.

• These symbols may appear next to a text (in which case they refer solely to the text itself), next to a figure (in

which case they refer to the topic illustrated in the figure and to the relative text), or at the top of the page (in which

case they refer to all the topics dealt with in the page).

NOTE The meaning of the symbols should be duly memorised as their scope is to avoid having to repeat

basic technical concepts or safety recommendations. They are therefore to be considered as “memory

tags”. In case of any doubt as to their meaning, consult the page in which they are fully described.

ABBREVIATIONS

UNITS OF MEASUREMENT

All the dimensions in this Manual are shown in

mm.

NOTE The letter V in the illustrations refers to fixing or adjusting screws. The number following this letter

refers to the number of the same type of screw in the unit or component described and illustrated. A

letter without a number indicates quantity 1. In case of different screws being referred to in the illustra-

tion, the letter V is followed by a number and a lower case letter. Example: (V4a).

Unless otherwise specified, units and components are reassembled by proceeding in the reverse

order of removal.

Figure

Tightening torque

Page

Paragraph

Section

Diagram

Table

Screw

INTRODUCTION

8

11/06

A

PASSWORD 250 i.e.

FRAME AND RUNNING GEAR

TABLE OF CONTENTS

1

GENERAL WORK PROCEDURES

• The advice, recommendations and warnings given hereafter are aimed at ensuring maximum work safety as well

as at considerably reducing the risk of accidents, personal injury, equipment damage and idle times. We therefore

recommend observing such advice, recommendations and warnings scrupulously.

SUGGESTIONS

• Only use top quality tools and equipment.

• Only use equipment conforming to EU Directives for lifting the vehicle.

• During all operations keep tools close at hand, ideally in accordance with a predetermined sequence of use, and

anyway never leave tools on the vehicle or in concealed or hard to reach positions.

• Always keep the work area clean and tidy.

• When tightening screws or nuts, start with the larger diameter or inner fasteners, and tighten them in a “crosswise

pattern” in successive “torquing steps”.

• Preferably use open-end wrenches and tighten by exerting “pulling force” rather than “pushing force”.

• Adjustable wrenches should only be used in case of

emergency, i.e. when a properly sized wrench is not

available. During the torquing stage the movable jaw

tends to open thus risking damaging the screw head or

achieving unreliable tightening torque values. In any

case, when using an adjustable wrench, take care to

proceed as shown in the figure.

• Except in the case of occasional services, prepare a

work sheet for the customer, on which to take a note of

all the work performed and write memos relating to any

future checks that may be required.

RECOMMENDATIONS

• Before carrying out any work on the vehicle wait for all

the parts to cool down completely.

• For operations requiring two mechanics, make sure that

the various steps to be performed by each of them are

clearly defined and coordinated beforehand.

• Make sure that each component has been properly fit-

ted before proceeding with the next one.

• Lubricate all parts (where applicable) before reinstall-

ing them.

• Gaskets, oil seals, snap rings and cotters must be re-

newed at every refitting.

• The torque settings specified in the manuals refer to

the “final torque”, which must be reached progressive-

ly by steps.

• Loosen and tighten aluminium alloy parts (covers) only

after the engine has cooled down fully.

• Only use screwdrivers of suitable sizes in relation to

the screws to be loosened or tightened.

• Work in a comfortable position and ensure that the ve-

hicle is stable.

• Never use a screwdriver as a lever or chisel.

• Never use pliers to loosen or tighten screws or nuts because, in addition to not providing a sufficient clamping force,

they may also damage the screw head or nut hex.

• Never tap wrenches with a hammer (or other similar tools) to loosen or tighten screws and nuts.

• Never attempt to increase leverage by attaching tubes, etc. to wrenches.

INTRODUCTION

9

11/06

A

PASSWORD 250 i.e.

FRAME AND RUNNING GEAR

TABLE OF CONTENTS

1

A

Never use open flames for any reason.

Never leave open containers or containers not suitable for holding fuel in passageways, close to

heat sources. etc.

Never use petrol to clean the vehicle or the workshop floor. Always use low flash point solvents to

clean the vehicle components.

Never suck from or blow into the fuel pipe.

When welding, make sure that there are no flammable liquids in the vicinity. Always remove the fuel

tank, even if completely empty, and disconnect the negative cable (-) from the battery.

Never leave the engine running in closed or poorly ventilated areas.

Before any servicing, make sure that the vehicle is perfectly stable.

The front wheel should preferably be anchored to fixture (A), which is integral with the lift platform.

INDICE

INTRODUCTION

10

11/06

A

PASSWORD 250 i.e.

FRAME AND RUNNING GEAR

TABLE OF CONTENTS

1

OPERATING SYMBOLS

IMPORTANT!

CAUTION! - Descriptions concerning operations that are potentially hazardous for the maintenance

mechanic or repairman, other workshop personnel or extraneous persons, for the environment, for the

vehicle, and for the tools and equipment.

DISCONNECT POWER - Before performing the work described, disconnect the battery negative cable.

RISK OF FIRE - Indicates operations that may constitute a fire hazard.

EXPLOSION HAZARD - Indicates operations that may constitute a risk of explosion.

TOXIC FUMES - Indicates the risk of intoxication or inflammation of the respiratory tract.

NO! - Operations to be absolutely avoided.

SYMMETRICAL OPERATIONS - Operations to repeat on both sides of the unit or component in question.

ENGINE WORKSHOP MANUAL - Information that can be found in the engine workshop manual.

FITTING AND ASSEMBLY OPERATIONS

REMOVAL AND DISASSEMBLY OPERATIONS

INDICEINTRODUCTION

11

11/06

A

PASSWORD 250 i.e.

FRAME AND RUNNING GEAR

2

GETTING TO KNOW YOUR SCOOTER

TECHNICAL DATA

MALAGUTI SpA reserves the right to modify technical data at any time without prior notice.

DIMENSIONS

wheel base (A), m ................................................ 1,484

max. length (B), m................................................ 2,170

max. width (C), m ................................................. 0,760

max. height (D), m................................................ 1,310

kerbside weight, kg.................................................. 170

max. load with rider, pillion and luggage, kg ............ 180

CAPACITIES

engine oil, cc ........................................................ 1400*

transmission oil, cc................................................. 250*

fuel tank (reserve), l........................................9,2* (3,5*)

* Guideline value

ENGINE: single cylinder, 2 valves - 4-stroke

type .............................................MINARELLI type 5MS

n° of cylinders.............................................................. 1

bore x stroke, mm .......................................Ø 69 x 66.8

displacement, cm

3

............................................... 249,78

compression ratio ...........................................10±0,4 : 1

cooling ................................................................... liquid

starting system .......................................electric starter

lubrication system .......................................... wet sump

SPARK PLUG

type .......................................................NGK DPR8EA9

TRANSMISSION

Primary: automatic speed variator with V-belt.

Final: gearbox.

Automatic centrifugal clutch

FUEL SYSTEM

Injection

Fuel: unleaded petrol.

IGNITION

MORIC control unit (5HW)

MORIC start-up coil (2JN)

BRAKES

Front brake:Ø 270 mm disc - hydraulic caliper with double

Ø 25 mm piston.

Rear brake: Ø 240 mm disc - hydraulic caliper with Ø 30

mm piston.

FRAME

High strength steel tubing.

SUSPENSION

Front: Hydraulic fork Ø 35 mm - travel: 110 mm

Rear: Swinging engine with double dual chamber

hydraulic shock absorber - travel: 110 mm

BATTERY

Type: 12V, 12Ah, sealed unit.

TYRES

Front: —— 110/70 - 16 60P (tubeless)

Rear: — 140/70 - 16 65P (tubeless)

It is possible to use tyres with load and speed indexes that

are higher than or identical to those indicated. It is howev-

er necessary for speed indexes to be identical for both

tyres.

GETTING TO KNOW YOUR SCOOTER

12

11/06

A

PASSWORD 250 i.e.

FRAME AND RUNNING GEAR

2

GETTING TO KNOW YOUR SCOOTER

13161415

1 2 3

4

5

6 87

10

9

12

11

2425

26

27

28

29

21

22

23

20

19

18

17

IDENTIFICATION OF MAIN

COMPONENTS (left-hand side)

1) Instrument panel

2) Windshield

3) Right-hand mirror

4) Keyswitch

5) Fuses

6) Twin seat

7) Fuel tank cap

8) Pillion grab handles

9) Rear turn indicators

10) Parking and stop lights

11) Number plate light

12) Number plate holder

13) Air filter

14) Centre stand

15) Side stand

16) Left-hand pillion bracket

17) Bag hook

18) Glove compartment

19) Left-hand mirror

IDENTIFICATION OF MAIN

COMPONENTS (right-hand side)

20) Front turn indicator

21) Front parking light

22) Headlights

23) Radiator

24) Coolant tank

25) Battery

26) Right-hand pillion bracket

27) Muffler

28) Anti-theft hook

29) Helmet compartment

13

11/06

A

PASSWORD 250 i.e.

FRAME AND RUNNING GEAR

2

GETTING TO KNOW YOUR SCOOTER

B

A

IDENTIFICATION DATA:

FRAME N° / ENGINE N°

• To gain access to the vehicle identification number (VIN)

(A), lift the right-hand rubber floor mat and remove the

cover.

• Engine identification data are located on the left-hand

engine crankcase (B).

Alteration of identification data is a criminal

offence.

• When ordering spare parts it is essential to quote the

vehicle identification data.

14

11/06

A

PASSWORD 250 i.e.

FRAME AND RUNNING GEAR

2

GETTING TO KNOW YOUR SCOOTER

T.W.I.

2 mm

TYRES

Type: Tubeless

NOTE It is possible to use tyres with load and speed

indexes that are higher than or identical to

those indicated. It is however necessary for

speed indexes to be identical for both tyres.

USE ONLY TYRES WITH THE RELEVANT

TYPE APPROVAL

Check the condition of your tyres (before each trip): if they are damaged (cracks) or cut, have them replaced as soon as

possible.

There are T.W.I. marks all around the tyre sidewalls. These correspond to tyre wear indicators situated in the tyre’s tread;

if there is no difference between the thickness of the tyre wear indicators and the tread depth, the tyre must be changed.

NOTE Minimum tread depth (front and rear) is 2 mm.

INFLATION PRESSURE

Tyre inflation pressure must be adjusted while the tyre is at ambient temperature.

NOTE Inflation pressure differing from the specified values can lead to higher fuel consumption, irregular

tyre wear, impaired vehicle performance and riding conditions.

15

11/06

A

PASSWORD 250 i.e.

FRAME AND RUNNING GEAR

2

GETTING TO KNOW YOUR SCOOTER

A

FUEL TANK

To access the fuel tank, proceed as follows:

• Place the scooter on the centre stand.

• Open the seat by turning the ignition key counter-clock-

wise.

• Unscrew cap (A) and refuel.

• After refuelling remove any traces of fuel from the scoot-

er body immediately since fuel may damage surface

finishes.

• The quantity of fuel and the use of the reserve fuel ca-

pacity are displayed by the relative function of the on-

board computer and the amber warning light on the right-

hand side of the instrument panel.

• Use UNLEADED PETROL.

* Guideline value

Petrol is extremely inflammable; avoid approaching the fuel filler - also when refuelling - with lit cigarettes

or naked flames (e.g. matches). Fire hazard!

FUEL TANK litres

TOTAL TANK CAPACITY 10*

RESERVE 3,5*

16

11/06

A

PASSWORD 250 i.e.

FRAME AND RUNNING GEAR

2

GETTING TO KNOW YOUR SCOOTER

A

B

MAX

MIN

COOLANT TANK

To access the engine coolant tank lift up the rubber mat on

the right-hand side.

Owing to the position of the tank, the level of coolant with

respect to the “MIN” and “MAX” level marks, can be checked

through the frame number inspection window (A) (see rel-

ative heading).

Use the coolant type prescribed in this man-

ual or a coolant with identical characteristics

when topping up the coolant tank.

To avoid burns never remove coolant tank

cap (B) when the engine is hot.

Do not top up with water except in emergen-

cy situations, in which case drain the tank

completely and fill with the prescribed cool-

ant as soon as possible.

REAR-VIEW MIRRORS

The left and right rear-view mirrors must be fitted to the

specific locations on the handlebar and firmly secured in

place.

Adjust the visual angle of the mirrors while sitting on the

scooter in its riding conditions. Orient the mirror until you

obtain the best visibility (A).

Take care: objects behind you are actually closer than they

appear when seen in the rear-view mirrors.

Do not adjust the rear-view mirrors while riding. Always

wait until you are stopped (e.g. at a traffic light).

17

11/06

A

PASSWORD 250 i.e.

FRAME AND RUNNING GEAR

2

GETTING TO KNOW YOUR SCOOTER

HELMET COMPARTMENT

• The helmet compartment is under the pillion seat. To

gain access to the compartment, put the scooter on its

stand and turn the ignition key counter-clockwise to

release the seat lock.

• The helmet compartment can accommodate a Jet type

helmet, positioned as shown in the figure.

Some types of helmet may not fit into the compartment.

Before choosing a helmet, make sure it fits into the

compartment.

• There is a 12V socket in the glove compartment that

can be used, for example, to recharge a mobile phone.

The socket must only be used with the engine running

and preferably with the lights off; note that using the

socket reduces battery recharging and can reduce the

battery charge level in certain circumstances.

Do not use the socket for appliances with an excessive

power draw (max. power draw: 30W).

The socket can also be used to recharge the battery by

connecting it to a battery charger for sealed batteries

when the engine is switched off.

Remember to refit the socket cap after using the socket

to prevent the ingress of foreign objects that could cause

short-circuits or other undesirable consequences.

The helmet compartment can be used to carry lightweight objects, which must be stowed in such a

way as to avoid negative effects on stability of the scooter while riding.

Do not insert items that are sensitive to high temperatures (lighters, inflammable liquids, perishable

goods, etc.).

Do not leave documents or valuables inside the helmet compartment.

18

11/06

A

PASSWORD 250 i.e.

FRAME AND RUNNING

GEAR

2

GETTING TO KNOW YOUR SCOOTER

B

A

C

GLOVE COMPARTMENT

The glove compartment is located in the central part of

the lower fairing (A) and is suitable for accommodating

small personal belongings.

It is fitted with a lock that can be opened with the ignition

key: turn the key clockwise.

The glove compartment contains the electrical system

fuses (B) and relative spare fuses (C) are contained in a

pocket in the door (see the relative section in the manual).

Do not place heavy objects or temperature

sensitive items (lighters, matches, inflamma-

ble liquids, perishable goods, etc.) in the

compartments. Do not leave documents or

valuables in the compartments.

19

11/06

A

PASSWORD 250 i.e.

FRAME AND RUNNING GEAR

GETTING TO KNOW YOUR SCOOTER

2

INSTRUMENT PANEL

1) Multifunction digital instrument panel

To set up the various functions refer to the

relative heading in the manual.

2) Analogue instruments. / Speedometer

Indicates the current speed in km/h and mph.

3) Coolant temperature indicator

The warning light comes on to indicate that

the coolant temperature is too high.

4) Red engine stop light

This light illuminates to indicate that the

“Engine Stop” button is set to OFF.

5) Green low beam indicator light

6) Blue high beam indicator light

7) Green left-hand turn indicator light

8) Green right-hand turn indicator light

9) Fuel level indicator

The warning light illuminates to indicate that

the reserve fuel level has been reached.

10) Injection warning light. When on or blinking

it indicates an anomaly in the injection

system.

11) This light is not used

The engine is not equipped with a pressure

probe so the oil warning light is not

connected and has checking purposes only.

Always observe the scheduled service

intervals (see MAINTENANCE TABLE) and the

instrument panel indications when the

keyswitch is set to ON.

Do not clean the instruments with high pres-

sure washers (risk of damage).

7

4

5

6

1

9

8

3

2

10

11

20

11/06

A

PASSWORD 250 i.e.

FRAME AND RUNNING GEAR

GETTING TO KNOW YOUR SCOOTER

2

3

2

1

DIGITAL INSTRUMENT PANEL

The digital instrument panel provides data for the rider to enable optimum management of the scooter.

When the ignition key is set to , all displays on the instrument panel will illuminate for approximately 3 seconds to

check that they are working correctly; the backlighting and warning lights will illuminate simultaneously for the same

reason.

During this phase the engine displacement, speedometer unit of measurement, and scooter model will appear on the

display.

The automatic check described above is performed every time the ignition key is turned to .

When this signal disappears, the following appear:

1)Secondary Menu or Submenu

2) Main Menu

3)Bar graph

To select a function, press the MODE button on the right-hand control. Operation of the MODE button is illustrated in the

following diagrams by means of an “arrow” symbol accompanied by the time for which the button must be held down. If

the time is not specified, momentary pressure on the button (< 1 sec.) is sufficient.

The available functions are divided into Main Menu and Secondary Menu or Submenu

.

The digital display can show warning and alarm signals that notify the rider when it is time to have the vehicle

serviced, when to change the engine oil, whether there is a risk of ice on the road, etc.; the alarm signals are illustrated

and explained below.

MODE button not

pressed for 4”

(total) (partial) (average) (time) (exterior)

Bar Graph

selection

Reset Reset

Time adjustment

Main Menu

selection:

Speed

No pressing

for 3”

Page is loading ...

Malaguti Password 250 i.e. Workshop Manual

Malaguti Password 250 i.e. Workshop Manual

Related papers

Other documents