Centurion RDE120 User manual

RDE120

Bruksanvisning(Swedish/English)

Robotdammsugare

Page is loading ...

SAFETY INSTRUCTIONS ----------------------------------------- EN-2

* Safety Instructions

* Battery and Recharging Instructions

SPECIAL FEATURES ---------------------------------------------- EN-3

MAJOR COMPONENTS AND ATTACHMENTS ------------- EN-3

OVERVIEW ------------------------------------------------------------ EN-4

BATTERY INSTALLATION AND REMOVAL ------------------ EN-5

RECHARGING BATTERY ----------------------------------------- EN-6

ADJUSTMENT OF ANTI-CLIFF SENSORS ------------------- EN-6

GENERAL OPERATION ------------------------------------------- EN-7

* Starting Operation

INSTALLING AND REMOVING SIDE BRUSH ---------------- EN-7

INSTALLATION GUIDE -------------------------------------------- EN-8

CLEANING AND MAINTENANCE ------------------------------- EN-9

* Cleaning Dust Bin

* Cleaning Intake

* Clean Side Burshes

TROUBLESHOOTING -------------------------------------------- EN-13

TABLE OF CONTENTS

SAFETY INSTRUCTIONS

EN-2

Please read the safety instructions in the Operation Manual before operating RDE120

and keep this manual handy for your future reference. Observe the basic safety rules

to prevent any occurrence of fire, electric shock and personal injury.

Safety Instructions

1. Please read the Operation Manual before operating RDE120.

2. Do not operate RDE120 outdoors.

3. Before starting RDE120, be sure to install the dust bin filter properly in case of any

damage of unit.

4. Do not operate RDE120 on wet floor or in moisture conditions, e.g. Bathroom.

Water and moisture could damage the circuit board in RDE120.

5. Prior to operate RDE120 remove any loose articles on the floor such as clothes, paper,

loose cables, and extension cords as well as making sure to lift curtains and drapes

off the floor to avoid any possible accidents. In case of a loose cable is tangled with

Robot, the cable might move around with the Robot as it works and topple down the

table, chairs, or cabinet and cause property damage.

6. Never stand or sit on the Robot. Beware of children or pets while Robot is in operation.

7. Never use Robot to clean up sparking cigarette butts or burning ashes form fireplace.

8. Never use Robot to clean up combustible or highly volatile liquids such as gasoline.

9. While Robot is in operation, make sure all doors leading outside are closed.

10. During operation, the heat vent should avoid being clogged. If heat vent clogged,

Robot could be damaged.

11. If Robot is malfunctioned or damaged by force, do not operate the Robot regardless

the cause. Please call your local dealer for service information.

12. Turn off the power and remove the battery from Robot if the unit will not in use for a

long period of time.

13. This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction concerning use of the

appliance by a person responsible for their safety.

14. Plug must be removed from the socket-outlet before cleaning or maintaining the

appliance.

15. Automatic battery-operated cleaners shall also be provided with cautionary

instructions for room preparation and constant care.

Battery and Recharging Instructions

1. The battery is rechargeable. Please use the voltage and current specified on the

packing. If you are not sure of the voltage and current of your house, please contact

your local power company or a licensed electrician.

2. Use only the battery supplied with your RDE120.

3. Charging adaptor is for indoors only.

4. Use only the charging adaptor supplied with your RDE120.

5. Do not recharge the battery if the cable or plug of the battery is damaged.

6. Never touch the charger, plug or cable with damped hands.

7. If Robot requires cleaning, unplug the adaptor, switch off the unit and take out the

battery.

8. Please take out the battery pack before disposing of the unit.

9. Please switch off the Robot before taking out the battery.

10. Please recycle and dispose the waste battery properly.

SPECIAL FEATURES

MAJOR COMPONENTS AND ATTACHMENTS

Random

Spiral

Along the wall

Spiral

EN-3

Congratulation on purchases the RDE120 Mini Vacuum Robot.

This revolution Mini Vacuum Robot is equipped with functions suitable for cleaning

up floor surfaces of home and office such as wood, tile, and linoleum. You can also

operate this unit with the provided micro fiber cloths to help you clean more effectively.

The RDE120 Mini Vacuum Robot is definitely a household helper.

O

peration

Man

ual

Dusting Paper x3

Cleaner unit

Rechargeable Battery x1

Dust Bin Filter x1

Dusting Paper Holder x1

Adaptor x1

Operation Manual x1

Side Brush x2

OVERVIEW

EN-4

Bumper

DC Jack Plug

Power Switch

Intake

Dusting Paper

Holder

Anti-Cliff Sensor

Side Brush

Upper Cover

Control Panel

Anti-Cliff Sensor

Left and Right

Wheels

Base

Battery Cover

Anti-Cliff

Sensor

Handle Grip

Front Small Wheel

Fig 1

Fig 2

BATTERY INSTALLATION AND REMOVAL

1. Make sure the power switch of RDE120 is turned off.

2. Remove the dusting paper holder.(Fig. 1)

3. Open the battery cover(see Fig. 2).

4. Insert the battery into the battery reservoir and close the cover.(Fig. 3)

5. To remove the battery, please follow step#3 above in reverse.

Battery reservoir

Fig 3

EN-5

RECHARGING BATTERY

1. To ensure the best performance of the rechargeable battery and lengthen its life span,

the battery is best used after fully charged for 4 hours every time.

The charging function will be cut off automatically for continuously charging 4 hours.

2. Before charging, make sure the battery is correctly installed and the power switch has

been turned to “OFF” position.

3. To charge, plug output of the d. c. adaptor into the DC jack plug of the RDE120 and the

input into the AC power outlet (Fig. 4).

4. When charging, the “CHARGE” LED indication lamp on the control panel of RDE120

(as below diagram) will flash green, and it will stay green when the battery is fully

charged.

5. When the “BATTERY LOW” LED indication lamp on the control panel(as below

diagram) will stay in RED.

If you forget to turn off the power of RDE120 before charging, after the cleaner is fully

charged, you have to switch off the cleaner and turn it on again to make it start

cleaning.

＊

ADJUSTMENT OF ANTI-CLIFF SENSORS

d.c. jack

Adaptor Plug

＊Control Panel with LED

CHARGE　　BATTERY LOW

OFF ON

(Fig 4)

There are three “Anti-Cliff” sensors at the bottom of RDE120 to prevent the unit from falling

down stairs.If the distance between the stair and the ground is shorter than usual,

please adjust all windows of “Anti-cliff” sensors to “◎” or “◎” or “◎” or “◎” position to

prevent the cleaner from falling down stairs. Please test it before it starts to clean.

ATTENTION: If the color of the floor is dark (ex. Black), it means that reflectivity of

the floor is bad, at this time, you have to open the window to a larger scale.

Please refer to the criteria of adjustment for adjusting the windows.

＊

The Criteria of Adjustment

Darker floor Lighter floor

Bigger drop Shorter drop

EN-6

GENERAL OPERATION

※ Caution: Remove the dusting paper holder & side brush before using on the carpet.

※ This product is not suitable for long-pile carpets.

1. Be sure the dust bin filter is installed properly.

2. Place the cleaner on place with more free space in the room, and turn on the power.

. When the cleaner runs out of power, the “BATTERY LOW” LED lamp on the unit will be

red and the cleaner will automatically stop.

. When the cleaner is not use or prior to recharging, make sure the power switch of RDE120

is in the “OFF” position.

Start Operation

3

4

INSTALLING AND REMOVING SIDE BRUSH

To install:Put the brushes directly onto the holder and spread the brush bristle evenly, then

press on the cap to fix it.(Fig. 5)

To Remove:Hold the brush bristle and pull upward to remove the brush.(Fig. 6)

Fig 5 Fig 6

PRESS

HOLD

PULL UP!

EN-7

Installing Dusting Paper

NOTE:

1. Remove the dusting paper holder following the instruction shown in Fig. 7.

2. Flat the dusting paper and put it one floor or table. Then place the holder (the side with

4 stoppers face up) on the paper at the midpoint as shown in Fig. 8.

3. Remove 4 stoppers from the holder, fold the hem of dusting paper on two sides back to

the holder, and place back 4 stoppers on top of the paper then press firmly to fix the

paper onto holder (Fig. 9).

4. Then place the dusting paper holder to the bottom of unit by aiming one bolt of holder at

the hole (near the big wheel) on cleaner, click the holder on the cleaner, and then do it

again for the other side. (Fig. 10)

1. Do not use mopping function on the carpet. At the same time you should remove the

side brushes to prevent it from damaging the brushes.

2. If you don’t need to use mopping function, please remove the dusting paper holder from

the cleaner (follow the instructions shown in Fig. 7) before you turn it on for cleaning.

INSTALLATION GUIDE

1

2

Lift up

Stoppers

Hole for the

stopper

Dust Paper

Fold back

Finished !

Press the two bolts on

the dusting paper holder

into the two holes on the

bottom of the cleaner.

Press

1

2

3

6

4

5

Fig 9

Fig 10

Fig 8

Fig 7

Push to

the left

EN-8

CLEANING AND MAINTENANCE

Cleaning Dust Bin

1. Left the top cover as shown in diagrams below.

2. Take out the dust bin from the cleaner.

Grip slot for the dust bin

EN-9

3. Open the upper cover of the dust bin.

4. Lift up and take out the filter.

5. Empty the dust bin.

CLEANING AND MAINTENANCE

EN-10

6. Rinse the dust bin with tap water . It is not necessary to wash every time.

Do not put it into the washing machine to clean it.

7. Periodically clean the filter with a soft bristle brush.

8. Once dry, reinstall the filter and the dust bin lid.

9. Place back the dust bin into the cleaner.

ATTENTION!! Before starting the cleaner, please be sure to install the dust

bin filter has properly installed in case any damage occurs.

CLEANING AND MAINTENANCE

EN-11

Cleaning Intake

After repeated use, dirt and dust could accumulate around the intake of the T270 and

might reduce the working efficiency. To ensure the best efficiency and constant

airflow, the intake should be cleaned periodically.

CLEANING AND MAINTENANCE

Clean Side Brushes

1. After being used for a period of time, the brushes need to be replaced for working

more effectively.

2. Turn off the power, place bottom of the cleaner upward on a flat surface. Hold the

brush bristle and pull upward to remove the brush (see diagram below).

3. The side brushes can be rinsed and if they become crooked, you can soak them in

hot water to make them recover to the original shape. Install the brushes back after

cleaning.

Intake

HOLD

PULL UP!

EN-12

TROUBLE SHOOTING

Robot is operable if the battery

has been charged on and off

over 4 hours.

Unit has the protective function

to cut off charging after 4

hour, if the LED indicator

keep blinking in Green after

4 hours, the power supply

might has been cutoff while

Unit was charging.

LED indicators keep

blinking GREEN after

4hrs charging.

4

Robot is on the floor in darker

color (it means the reflectivity

of floor is bad)

Please adjust all windows of

“Anti-cliff” sensors.

(Please refer to page 6.)

3

1. Clean the dust bin.

2. Re-install the filter

correctly.

1. The dust bin is full.

2. The filter is not installed

correctly.

Vacuum on but can not

collect dirt on hair

2

1

1. Recharge the battery.

2.Place Robot back to floor.

1. Battery Low condition.

2.Robot is lifted from floor.

Red LED stays after

power on.

1.To install the battery

correctly, please refer to

the Operation Manual for

battery installation.

2. To have the battery fully

charged. (Turn off the

cleaner first.)

1. The battery is not

installed properly.

2. Battery power is low.

Cannot start the Robot.

Unit circles around only,

cannot go straight.

One of the wires of the

wheels might be loosened.

Open the wheel cover and

connect the loosen wire of

the wheel properly or contact

your local dealer for service.

6

7

If it becomes crooked, you

could scald it in hot water to

recover it to its original

shape.

Being used for a long time.

The side brush had

become crooked, not

good to sweep.

5

Problem

Possible Cause

Solution

Robot is moving backwards

after being started.

※ If the solution can not solve the problem, Please contact to your local dealer for

service.

EN-13

This symbol on the product or in the instructions means that your electrical and

electronic equipment should be disposed at the end of its life separately from your

household waste. There are separate collection systems for recycling in the EU.

For more information, please contact the local authority or your retailer where you

purchased the product.

Page is loading ...

Centurion RDE120 User manual

Centurion RDE120 User manual

in other languages

Related papers

Other documents