RDE125
Bruksanvisning(Swedish/English)
Robotdammsugare
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
SAFETY INSTRUCTIONS ----------------------------------------------- EN-2
* Safety Instructions
* Battery and Recharging Instructions
SPECIAL FEATURES ---------------------------------------------------- EN-3
MAJOR COMPONENTS AND ATTACHMENTS ------------------- EN-3
RDE125 OVERVIEW ------------------------------------------------------ EN-4
BATTERY INSTALLATION AND REMOVAL ------------------------ EN-5
RECHARGING BATTERY ----------------------------------------------- EN-6
ADJUSTMENT OF ANTI-CLIFF SENSORS ------------------------- EN-6
GENERAL OPERATION ------------------------------------------------- EN-7
* Starting Operation
INSTALLING AND REMOVING SIDE BRUSH ---------------------- EN-7
INSTALLATION GUIDE -------------------------------------------------- EN-8
CLEANING AND MAINTENANCE ------------------------------------- EN-9
* Cleaning Dust Bin
* Cleaning Intake
* Clean Side Burshes
TROUBLESHOOTING -------------------------------------------------- EN-13
TABLE OF CONTENTS
SAFETY INSTRUCTIONS
EN-2
Please read the safety instructions in the Operation Manual before operating RDE125 and
keep this manual handy for your future reference. Observe the basic safety rules to prevent
any occurrence of fire, electric shock and personal injury.
Safety Instructions
1. Please read the Operation Manual before operating RDE125.
2. Do not operate RDE125 outdoors.
3. Before starting RDE125, be sure to install the RDE125 dust bin filter properly in case of
any damage of RDE125.
4. Do not operate RDE125 on wet floor or in moisture conditions, e.g. Bathroom. Water and
moisture could damage the circuit board in RDE125.
5. Prior to operate RDE125 remove any loose articles on the floor such as clothes, paper,
loose cables, and extension cords as well as making sure to lift curtains and drapes off
the floor to avoid any possible accidents. In case of a loose cable is tangled with
RDE125, the cable might move around with RDE125 as RDE125 works and topple down
the table, chairs, or cabinet and cause property damage.
6. Never stand or sit on RDE125. Beware of children or pets while RDE125 is in operation.
7. Never use RDE125 to clean up sparking cigarette butts or burning ashes form fireplace.
8. Never use RDE125 to clean up combustible or highly volatile liquids such as gasoline.
9. While RDE125 is in operation, make sure all doors leading outside are closed.
10. During operation, the heat vent should avoid being clogged. If heat vent clogged,
RDE125 could be damaged.
11. If RDE125 is malfunctioned or damaged by force, do not operate RDE125 regardless
the cause. Please call your local dealer for service information.
12. Turn off the power and remove the battery from RDE125 if the unit will not in use for a
long period of time.
13. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
14. Plug must be removed from the socket-outlet before cleaning or maintaining the
appliance.
15. Automatic battery-operated cleaners shall also be provided with cautionary instructions
for room preparation and constant care.
Battery and Recharging Instructions
1. The battery is rechargeable. Please use the voltage and current specified on the packing.
If you are not sure of the voltage and current of your house, please contact your local
power company or a licensed electrician.
2. Use only the battery supplied with your RDE125.
3. Charging adaptor is for indoors only.
4. Use only the charging adaptor supplied with your RDE125.
5. Do not recharge the battery if the cable or plug of the battery is damaged.
6. Never touch the charger, plug or cable with damped hands.
7. If RDE125 requires cleaning, unplug the adaptor, switch off the unit and take out the
battery.
8. Please take out the battery pack before disposing of the unit.
9. Please switch off RDE125 before taking out the battery.
10. Please recycle and dispose the waste battery properly.
SPECIAL FEATURES
MAJOR COMPONENTS AND ATTACHMENTS
Random
Spiral
Along the wall
Spiral
EN-3
Congratulation on purchases the RDE125 Mini Vacuum Robot.
This revolution Mini Vacuum Robot is equipped with functions suitable for cleaning
up floor surfaces of home and office such as wood, tile, and linoleum. You can also
operate this unit with the provided micro fiber cloths to help you clean more effectively.
The RDE125 Mini Vacuum Robot is definitely a household helper.
O
p
e
ra
tio
n
Ma
n
u
al
Dusting Paper x3
RDE125 Cleaner x1
Rechargeable Battery x1
Dust Bin Filter x1
Dusting Paper Holder x1
Adaptor x1
Operation Manual x1
Side Brush x2
RDE125 OVERVIEW
EN-4
Bumper
DC Jack Plug
Power Switch
Intake
Dusting Paper
Holder
Anti-Cliff Sensor
Side Brush
Upper Cover
Control Panel
Anti-Cliff Sensor
Left and Right
Wheels
Base
Battery Cover
Anti-Cliff
Sensor
Handle Grip
Front Small Wheel
Fig. 2
Fig. 1
BATTERY INSTALLATION AND REMOVAL
1. Make sure the power switch of RDE125 is turned off.
2. Remove the dusting paper holder.(Fig. 1)
3. Open the battery cover(see Fig. 2).
4. Insert the battery into the battery reservoir and close the cover.(Fig. 3)
5. To remove the battery, please follow step#3 above in reverse.
Battery reservoir
Fig. 3
EN-5
RECHARGING BATTERY
1. To ensure the best performance of the rechargeable battery and lengthen its life span,
the battery is best used after fully charged for 4 hours every time.
The charging function will be cut off automatically for continuously charging 4 hours.
2. Before charging, make sure the battery is correctly installed and the power switch has
been turned to “OFF” position.
3. To charge, plug output of the d. c. adaptor into the DC jack plug of the RDE125 and
the input into the AC power outlet (Fig. 4).
4. When charging, the “CHARGE” LED indication lamp on the control panel of RDE125
(as below diagram) will flash green, and it will stay green when the battery is fully
charged.
5. When the “BATTERY LOW” LED indication lamp on the control panel(as below
diagram) will stay in RED.
＊If you forget to turn off the power of RDE125 before charging, after the cleaner is
fully charged, you have to switch off the cleaner and turn it on again to make it start
cleaning.
ADJUSTMENT OF ANTI-CLIFF SENSORS
d.c. jack
Adaptor Plug
＊Control Panel with LED
CHARGE BATTERY LOW
OFF ON
(Fig. 4)
There are three “Anti-Cliff” sensors at the bottom of RDE125 to prevent the unit from
falling down stairs.If the distance between the stair and the ground is shorter than
usual, please adjust all windows of “Anti-cliff” sensors to “◎” or “◎” or “◎” or “◎” position
to prevent the cleaner from falling down stairs. Please test it before it starts to clean.
＊ATTENTION: If the color of the floor is dark (ex. Black), it means that reflectivity of
the floor is bad, at this time, you have to open the window to a larger scale.
Please refer to the criteria of adjustment for adjusting the windows.
The Criteria of Adjustment
Darker floor Lighter floor
Bigger drop Shorter drop
EN-6
GENERAL OPERATION
※ Caution: Remove the dusting paper holder & side brush before using on the carpet.
※ This product is not suitable for long-pile carpets.
1. Be sure the dust bin filter is installed properly.
2. Place the cleaner on place with more free space in the room, and turn on the power.
3. When the cleaner runs out of power, the “BATTERY LOW” LED lamp on the unit will
be red and the cleaner will automatically stop.
4. When the cleaner is not use or prior to recharging, make sure the power switch of
RDE125 is in the “OFF” position.
Start Operation
INSTALLING AND REMOVING SIDE BRUSH
To install:Put the brushes directly onto the holder and spread the brush bristle evenly,
then press on the cap to fix it.(Fig. 5)
To Remove:Hold the brush bristle and pull upward to remove the brush.(Fig. 6)
Fig. 5 Fig. 6
PRESS
HOLD
PULL UP!
EN-7
Installing Dusting Paper
NOTE:
1. Remove the dusting paper holder following the instruction shown in Fig. 7.
2. Flat the dusting paper and put it one floor or table. Then place the holder (the side with
4 stoppers face up) on the paper at the midpoint as shown in Fig. 8.
3. Remove 4 stoppers from the holder, fold the hem of dusting paper on two sides back to
the holder, and place back 4 stoppers on top of the paper then press firmly to fix the
paper onto holder (Fig. 9).
4. Then place the dusting paper holder to the bottom of unit by aiming one bolt of holder at
the hole (near the big wheel) on cleaner, click the holder on the cleaner, and then do it
again for the other side. (Fig. 10)
1. Do not use mopping function on the carpet. At the same time you should remove the
side brushes to prevent it from damaging the brushes.
2. If you don’t need to use mopping function, please remove the dusting paper holder from
the cleaner (follow the instructions shown in Fig. 7) before you turn it on for cleaning.
INSTALLATION GUIDE
1
2
Lift up
Stoppers
Hole for the
stopper
Dust Paper
Fold back
Fold back
Finished !
Press the two bolts on
the dusting paper holder
into the two holes on the
bottom of the cleaner.
Press
Press
Press
Press
1
2
3
6
4
5
Fig. 9
Fig. 10
Fig. 8
Fig. 7
Push to
the left
EN-8
CLEANING AND MAINTENANCE
Cleaning Dust Bin
1. Left the top cover as shown in diagrams below.
2. Take out the dust bin from the cleaner.
Grip slot for the dust bin
EN-9
3. Open the upper cover of the dust bin.
4. Lift up and take out the filter.
5. Empty the dust bin.
CLEANING AND MAINTENANCE
EN-10
6. Rinse the dust bin with tap water . It is not necessary to wash every time.
Do not put it into the washing machine to clean it.
7. Periodically clean the filter with a soft bristle brush.
8. Once dry, reinstall the filter and the dust bin lid.
9. Place back the dust bin into the cleaner.
ATTENTION!! Before starting the cleaner, please be sure to install the dust
bin filter has properly installed in case any damage occurs.
CLEANING AND MAINTENANCE
EN-11
Cleaning Intake
After repeated use, dirt and dust could accumulate around the intake of the RDE125
and might reduce the working efficiency. To ensure the best efficiency and constant
airflow, the intake should be cleaned periodically.
CLEANING AND MAINTENANCE
Clean Side Brushes
1. After being used for a period of time, the brushes need to be replaced for working
more effectively.
2. Turn off the power, place bottom of the cleaner upward on a flat surface. Hold the
brush bristle and pull upward to remove the brush (see diagram below).
3. The side brushes can be rinsed and if they become crooked, you can soak them in
hot water to make them recover to the original shape. Install the brushes back after
cleaning.
Intake
HOLD
PULL UP!
EN-12
TROUBLE SHOOTING
※ If the solution can not solve the problem, Please contact to your local dealer for
service.
EN-13
This symbol on the product or in the instructions means that your electrical and
electronic equipment should be disposed at the end of its life separately from your
household waste. There are separate collection systems for recycling in the EU.
For more information, please contact the local authority or your retailer where you
purchased the product.
RDE125 is operable if the
battery has been charged on
and off over 4 hours.
RDE125 has the protective
function
to cut off charging after 4
hour, if the LED indicator
keep blinking in Green after
4 hours, the power supply
might has been cutoff while
RDE125 was charging.
4
RDE125 is on the floor in
darker color. (it means the
reflectivity of floor is bad)
Please adjust all windows of
“Anti-cliff” sensors.
(Please refer to page 6.)
3
1. Clean the dust bin.
2. Re-install the filter
correctly.
1. The dust bin is full.
2. The filter is not installed
correctly.
Vacuum on but can not
collect dirt on hair.
2
1
1. Recharge the battery.
2. Place RDE125 back to
floor.
1. Battery Low condition.
2. RDE125 is lifted from
floor.
Red LED stays after
power on.
1.To install the battery
correctly, please refer to
the Operation Manual for
battery installation.
2. To have the battery fully
charged. (Turn off the
cleaner first.)
1. The battery is not
installed properly.
2. Battery power is low.
Cannot start the
RDE125.
RDE125 circles around
only, cannot go
straight.
One of the wires of the
wheels might be loosened.
Open the wheel cover and
connect the loosen wire of
the wheel properly or contact
your local dealer for service.
6
7
If it becomes crooked, you
could scald it in hot water to
recover it to its original
shape.
Being used for a long time.
The side brush had
become crooked, not
good to sweep.
5
Problem
Possible Cause
Solution
RDE125 is moving
backwards after being
started.
LED indicators keep
blinking GREEN after
4hrs charging.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
