Pontiac 2003 Vibe User manual

Brand: Pontiac

Model: 2003 Vibe

Category: Car navigation systems

Type: User manual

The 2003 Pontiac Vibe Navigation System Supplement

This supplement contains information on the operation of the Navigation System in your vehicle. This supplement,

along with your owner’s manual, will assist you in the proper use of the system. If you have any problems using the

system, please contact your dealer.

-1 Overview

Here the supplement gives you basic information that you will need to know to be able to operate your

Navigation System.

2-1 Features

This section shows the different features available on your Navigation System.

3-1 Navigation Audio System

This section explains how to use the audio system included with your Navigation System.

4-1 If a Problem Occurs

This section explains what to do if you experience a problem with the Navigation System.

Litho in U.S.A. Copyright General Motors Corporation 01/07/02

GENERAL MOTORS, GM, the GM Emblem,

PONTIAC, and the PONTIAC Emblem are registered

trademarks and the name VIBE is a trademark of

General Motors Corporation.

This manual includes the latest information at the time it

was printed. We reserve the right to make changes in the

product after that time without notice.

Please keep this supplement with the owner’s manual in

your vehicle, so it will be there if you ever need it while

you’re on the road. If you sell your vehicle, leave the

owner’s manual supplement and the owner’s manual

with the vehicle.

1-1

Section 1Overview

Here you’ll find basic information about the features of your Navigation System and how they are used.

1-2 Introduction

-3 Global Positioning System (GPS)

-4 Maps

-5 Using the Navigation System

-8 Screen Setup

-10 Adjust Clock

1-2

Introduction

S–29–0023–3

Before you begin to operate this system, read this

manual thoroughly to become familiar with it and to

understand how the system works.

The Navigation System allows you to do the following:

Plan a route with provided turn

-by-turn route and

map guidance with voice prompts.

Select a destination from various areas and choices

(i.e. street addresses, intersections, marked points,

points of interest, etc.).

Receive broadcast announcements on traffic and

emergency alert communications.

The information in the system may not always be

complete. Road conditions, such as prohibited turns,

detours and construction zones, change frequently.

It is important to consider whether you can follow

the directions given by the system for the current

conditions.

1-3

Global Positioning System (GPS)

The Navigation System determines the position of your

vehicle by using satellite signals, various vehicle signals

and map data.

The Global Positioning System (GPS) locates the

current position of your vehicle using signals sent by the

United States Department of Defense GPS Satellites.

While your vehicle is receiving signals from the

satellites, GPS will appear on the map screen.

However, at times, other interferences such as the

satellite condition, road configuration, the condition of

the vehicle and/or other circumstances can interfere with

the system’s ability to determine the accurate position of

the vehicle.

This system may not be available or interference may

occur if any of the following are true:

Signals are obstructed by tall buildings, large trucks

or a tunnel.

Metallic objects are located on the dashboard.

Satellites are being repaired or improved.

Aftermarket glass tinting has been applied to the

vehicle’s windshield.

Do not apply aftermarket glass tinting to the vehicle’s

windshield or place metallic objects on the vehicle’s

dashboard. Glass tinting and metallic objects will

interfere with the system’s ability to receive GPS signals

and may cause the system to malfunction.

If you are experiencing a problem, see “Vehicle

Positioning” and “Problems with Route Guidance” in

the Index for more information.

1-4

Maps

This section includes basic information that you need to

know about the map database.

The maps are stored on a DVD

-ROM. The United

States (excluding Alaska and Hawaii) and portions of

Canada are contained in one disc. The United States

map database includes the interstate freeways, state

highways, country roads and major and general streets.

Refer to the “Navigation System Map Disc” manual to

view the explanation of map coverage. This manual will

be in your map DVD case when the vehicle is delivered

from the factory.

When your vehicle is delivered from the factory, the

dealer may have installed the map DVD. If the DVD

was not installed in your vehicle when first purchased,

use the following directions to load the DVD:

1.Turn the ignition switch to ON or ACCESSORY.

2.If already loaded, eject the map DVD or a CD from

the slot.

3.Load the map DVD into the slot by inserting it

partway. The system will pull it in.

Once the DVD is inserted correctly, you will have the

following two choices:

ENG (English)

FR (French)

I AGREE

You can change the language to one of the two that are

available by using the control pad located on the bottom

left corner of the navigation system, to select a language

and press the ENT button to choose the selection. Once

a language is selected, select I AGREE to plan a route.

The map will appear showing your current vehicle

position.

Map Adjustments

The system allows you to adjust the scale of view on the

map. Also, the map will scroll automatically based on

the direction you are traveling.

To view a larger or smaller scale of the map, press the

Zoom In or Zoom Out symbol keys. See “Zoom In/Out”

later in this section for more information on these keys.

Map Scales

The scale of a map can range from 1/32 of a mile

(0.05 km) to 128 miles (206 km).

1-5

Using the Navigation System

This section describes the basic information you will

need to know to operate the Navigation System.

The navigation screen shows a number of icons that

offer information on a variety of topics.

Use the keys, located on each side of the navigation

screen, and the control pad, located at the bottom left

corner of the faceplate, to operate the system.

Use the left and right arrows on the control pad to move

horizontally on the screen and the up and down arrows

on the control pad to move vertically on the screen. Use

the ENT button in the center of the control pad to

choose your desired selection.

Once the vehicle is running, various functions will be

disabled to reduce driver distraction.

Hard Keys

The following hard keys are located to the left of the

navigation screen:

(Eject)

SEEK

NAV

BAND

(AUDIO)

SETUP

Refer to the Index for more information on each of these

hard keys to learn what they can do.

The system also has the following reconfigureable soft

keys located to the right of the navigation screen. These

have hard key labels for easier understanding while in

navigation mode. The six keys change functions for

different modes of the system.

MAP

DEST

(Zoom In)

(Zoom Out)

BACK

1-6

These keys allow you to do the following:

NV–31–0006–2

NV–31–0005–2

Zoom In Zoom Out

Press Zoom In to get a closer look at the map you are

traveling on. Locate a destination easily by zooming

in to see a smaller section of the map, if you are

close to your destination.

Press Zoom Out to see a larger scale of the map, if

the destination that you wish to reach is a long

distance from your current location. You can also

view your highlighted route.

Key Pad

The letters, symbols and punctuation available to you

are displayed on the alpha bar. The alpha bar will

automatically be available whenever the system needs

information from you. Make your selection by pressing

the ENT button on the center of the control pad.

To enter a space between the words of a name, you must

use the control pad and select the space symbol, which

is at the end of the keypad.

To make your name selections easier, the system will

only allow you to select a character which can follow

the last one entered. For example, if you enter Z, you

wouldn’t be allowed to follow it with T. The system will

highlight the available characters and darken the

unavailable characters.

If you select an incorrect character, press the back space

symbol button.

If you are unsuccessful when inputting a name, it may

need to be selected differently. It is possible that the map

DVD (database) may not contain that information. See

“Database Coverage Explanations” in the Index.

1-7

Numeric Bar

The numbers available to you are displayed. The

numerals will automatically be available whenever the

system needs you to input a phone number or house

address. You can cycle through the list using the control

pad and make your selections by pressing the ENT

button on the center of the control pad.

Symbols

The following symbols are the most common that

appear on a map screen.

S–29–1015–3

Your vehicle is shown as

this symbol. It indicates the

current position of your

vehicle on the map.

S–29–1016–3

This symbol will appear

on the map after a route

has been planned showing

your destination.

See “Destination (DEST)” in the Index for information

on planning a route.

When one of five possible destinations has been set,

you will see a circle with the number, 1

-5, of which

destination it is.

1-8

S–29–1017–3

This symbol indicates the

map with North up.

Regardless of the direction of vehicle travel, North is

always up on the screen.

S–29–1018–3

This symbol indicates the

map with the vehicle travel

direction up.

The shaded triangle indicates North. By selecting map

orient while on the map screen, you can see your vehicle

always traveling in an up direction on the screen even

though you are not traveling North.

Screen Setup

S–29–0001–3

Press the SETUP hard key, located on the left side of the

navigation screen, to access the Setup Menu.

The Setup Menu allows you to adjust such things as

screen colors, and language of the display for the

Navigation System.

1-9

Day and Night Screen Changes

When the headlamp switch is turned on, the screen will

change to a lighter background for better viewing in the

daytime. At night, the screen will go to a darker

background.

You can also select day or night mode regardless of the

lighting conditions. The Day setting leaves the system in

the day mode. The Night setting leaves the system in

the night mode.

Brightness

To adjust the brightness, press the SETUP hard key and

then choose the option you wish to adjust by pressing

the key beside it. Use the control pad to raise or lower

the brightness to the desired level. You will see the

screen change as you adjust the brightness.

Volume

To adjust the volume of the voice prompts you receive

from the system, select Volume after pressing the

MENU key. Use the control pad to raise or lower the

volume. The voice prompt will come on with each

adjustment to give you an idea of the volume at

each level.

Once you have reached the volume level you desire,

press the center of the control pad to set the volume and

press the Back key to return to the previous screen.

1-10

Adjust Clock

S–29–0020–3

To adjust the time displayed at the lower right corner of

the navigation screen, select the Adjust Clock option

from the Setup Menu.

OK: Allows you to set your selections.

Hours/Minutes: To change the time on the clock

press the Adjust button and use the control pad to

change the time. Press the ENT button when the desired

time is reached.

12Hr/24Hr: This feature allows you to decide whether

the time is displayed in standard or military time. Use

the control pad to select which one is desired.

Once you have the time set, you must hit the OK key to

save your changes and return to the Setup Menu. If you

hit the BACK key, you will still return to the Setup

Menu, but none of your changes will be saved.

Auto GPS Update: This key sets the Navigation

System’s time to match the current GPS time. The time

will be updated with the GPS time when the ignition is

turned to ACC or ON.

Daylight Savings: Use the control pad to toggle

between Daylight Savings Time On or Off.

Time Zone: This menu allows you to choose from

four different time zones: Pacific, Mountain, Central and

Eastern. Use the control pad to scroll through the zones.

When you have reached the desired zone, press the ENT

button on the center of the control pad to select it.

1-11

Calendar

S–29–1013–3

To access the calendar function, press the SETUP

hardkey to get to the setup screen. Press the Calendar

button to display the Calender screen. Here you can

input memos or information for important dates.

Maintenance Information

This system had a function which informs you of the

time to replace certain parts of components on your

vehicle. When the navigation system begins to operate

and the vehicle has reached either the information item’s

replacement date or the appropriate driving distance, the

Information screen will automatically be displayed. You

can turn off the Information screen by selecting “Do not

display this message again.”

To access this screen, press the SETUP key and select

the Maintenance button to display the Maintenance

screen. Select your desired icon from the screen and

input the next maintenance date and driving distance

until the next check.

1-12

S–29–1014–3

You can also choose Set dealer from the Maintenance

screen. This allows you to register your dealer’s name

and address. After you enter your dealer’s name and

address, the screen changes and displays the map

location of the dealer.

You can also edit your dealer’s name, location and

phone number if you have already registered the dealer.

After you select the Set dealer button on the

Maintenance screen the Edit dealer screen appears.

Select the Change button to edit the dealer’s

information. Select the Delete dealer button on the Edit

dealer screen to delete a dealer’s information all

together.

1-13

Language

Your vehicle has been set for the English language, but

you may also select French for all instructional text and

voice prompts. However, names on the location map

when using the navigation functions will not change.

If you wish to change the language, do the following:

1.Press the Language key under the Setup Menu, a

caution will display.

2.Use the control pad to toggle to the language

you prefer.

3.Press the ENT button in the center of the control pad

to choose a language.

4.Select I AGREE to change the display back to the

map display.

If the language is changed from English, the menu

screens will not match word

-for-word as they appear in

this supplement. If you accidentally set a language and

you do not understand the menus, turn your engine off.

Your Navigation System will turn off. You will then be

able to select a different language when the system starts

up again, using the control pad to select the language.

English/Metric Units

You can select either English or metric measurements to

appear for distances on the map.

To change between English and metric measurements,

do the following:

1.Press the MENU button.

2.Press Setup on the menu display.

3.Choose from the measurement options listed:

kilometer/meter.

4.Use the control pad to move to the measurement

option you desire. Press the ENT button in the center

of the control pad to choose it.

5.Press the Back key to return to the previous screen.

2-1

Section 2Features and Controls

Here you’ll find information about features available on your Navigation System and how to use them.

2-2 Navigation System Screen

-2 PWR/VOL (Power/Volume) Knob

-3 NAV (Navigation) Key

-4 Navigation Menu

-5 Navigation Menu Options Display

-5 Suspend Guidance

-5 Route Overview

-5 Volume

-6 Edit Route

-6 Route Preview

-7 Setup

-7 Marked Points

-8 DEST (Destination)

-13 Points of Interest

-17 Colors on the Screen

2-2

Navigation System Screen

S–29–0023–3

This display screen is located in the center of your

instrument panel. In this section, the hard keys,

multi

-function keys and menus to plan a route

are explained.

PWR/VOL (Power/Volume) Knob

Press the PWR/VOL knob to turn on the audio and

Navigation Systems. Turn the PWR/VOL knob to

increase or to decrease the volume to the audio system.

Press the knob again to turn off the audio and

Navigation Systems.

2-3

NAV (Navigation) Key

If you are in a menu and are not on the map, the first

press of the NAV key, located to the left of the display

screen, will take you to the map that shows the vehicle’s

current position.

If no route has been planned, the first press of the NAV

key will show the map screen and also the following

information:

The north or heading up symbol in the upper

left corner.

The letters GPS to show that the Global Positioning

System is working.

The time.

The map scale.

If a route has been planned, the first press of the NAV

key will show the map screen and also display:

The number of miles/meters until you reach your

destination.

The estimated time to your destination.

The highlighted destination or turn

-by-turn

instructions.

To learn more about the features shown on the map

screen, you can find each feature listed in the Index.

The second press of the NAV key will bring up

descriptions of the multi-function keys active on

the map screen.

NAV Repeat

You can press the MAP button to have the current audio

navigation prompt repeated.

2-4

Navigation Menu

S–29–0017–3

The main navigation menu allows you to choose from

an itemized list of options or to use the multi

-function

keys to make adjustments to the system and plan routes.

You will be able to choose from the following list of

items on the main navigation menu:

Suspend Guidance

Route Overview

Map Appearance

Volume

DVD (DVD Information)

Edit Route

Route Preview

Setup

Marked Points

These multi

-function keys are also available:

MAP

DEST (Destination)

Zoom In

Zoom Out

BACK

Page is loading ...

Pontiac 2003 Vibe User manual

Brand: Pontiac

Model: 2003 Vibe

Category: Car navigation systems

Type: User manual

Download PDF

report

Pontiac 2003 Vibe User manual

Pontiac 2003 Vibe User manual

Related papers

Other documents