Barco X-PORT DCC 120 Quick start guide

Barco
Brand
Barco
Model
X-PORT DCC 120
Type
Quick start guide

This manual is also suitable for

Barco X-PORT DCC 120 is a module that adds extra capabilities to your projector. Once the device is inserted, it enables you to project 3D content to your audience in multiple ways.

The device offers support for both dual input 3D and double flash 3D. This means that you can connect two separate sources (such as a Blu-ray player and a game console) to the projector and display 3D content from both sources simultaneously. Alternatively, you can connect a single source that supports double flash 3D, and the projector will convert the signal to a standard 3D feed.

The X-PORT DCC 120 is easy to install. Simply locate the X-PORT connector on your projector and press the module into place. The four retainer screws will keep the module securely fastened.

Barco X-PORT DCC 120 is a module that adds extra capabilities to your projector. Once the device is inserted, it enables you to project 3D content to your audience in multiple ways.

The device offers support for both dual input 3D and double flash 3D. This means that you can connect two separate sources (such as a Blu-ray player and a game console) to the projector and display 3D content from both sources simultaneously. Alternatively, you can connect a single source that supports double flash 3D, and the projector will convert the signal to a standard 3D feed.

The X-PORT DCC 120 is easy to install. Simply locate the X-PORT connector on your projector and press the module into place. The four retainer screws will keep the module securely fastened.

Quick Start Guide
X-PORT
DCC 120
functionality
1
The X-PORT DCC120 module is designed to support dual input 3D (left and right eye in separate cables) and double flash 3D.
For dual input 3D, 2 x HDMI or 2 x DVI or 2 x VGA with left and right eye information on the 2 chosen connectors is then supported.
For double flash 3D, sequential 3D is supported between 48 and 60 Hz (24 to 30 Hz per eye) on a single input connector. The input
signal will then be converted to a standard 3D feed between 96 and 120 Hz.
Update the projectors software before attaching the X-PORT module. The software is easily available from our web site.
2
connecting the module
Locate X-PORT 1 on your projector (left hand side - see picture 2). Make sure that both the projector and the source have mains
disconnected and are switched off before attaching the X-PORT module. Refusing to follow these instructions may damage both the
projector and the X-PORT module.
Fit the X-PORT module to the connector on the projector using the guiding pins, and press into place. Fasten the four retainer screws
(see picture 1), using a screwdriver. Take care not tightening the screws too hard as this may damage the threads.
3
connecting sources
The X-PORT DCC120 module does not have any input connectors.
Sources are connected to the projector as described in the user guide.
4
indicator lamps
The X-PORT DCC120 module has one LED indicator on the right hand side ((picture 1/STATUS). The LED indicator will be illuminated in
green when the module is operational and red if an error is detected.
PICTURE 1
PICTURE 2
Retainer screws
Retainer screws
LED
indicator
(STATUS)
X-PORT 1 /
DCC 120
X-PORT 2 /
(OPTIONAL)
601-0320-00
For further information, please refer to the projector user guide or our web site
www.barco.com
WEEE INFORMATION
This product conforms to all requirements of the EU
Directive on waste electrical and electronic equipment
(WEEE). This product shall be recycled properly. It can
be disassembled to facilitate proper recycling of it’s
individual parts. Consult your dealer or relevant public
authority regarding drop-off points for collection of WEEE.
WARNING SYMBOLS
RECYCLE Warning! Recycle properly, do not
dispose of in ordinary waste!
WEEE-ANGABEN
Dieses Produkt erfüllt alle Auflagen aus der EU-Richtlinie
für Elektro- und Elektronik-Altgeräte (WEEE). Dieses
Produkt kann sachgemäß recycelt werden. Es kann
zerlegt werden, um die Einzelteile ordnungsgemäß zu
recyceln. Fragen Sie Ihren Händler oder die zuständigen
Behörden nach Entsorgungsstellen für Elektro- und
Elektronik-Altgeräte.
WARNSYMBOLE
RECYCELN Warnung! Sachgemäß recyceln und
nicht mit dem gewöhnlichen Abfall entsorgen!
INFORMATION WEEE
Cet appareil est conforme à la Directive EU relative au
recyclage des équipements électriques et électroniques
(WEEE). Cet appareil doit être recyclé correctement. Il
peut être démonté pour faciliter le recyclage de chaque
pièce séparément. Consultez votre revendeur ou les
autorités publiques compétentes concernant les points
de collecte WEEE.
SYMBOLES D’AVERTISSEMENT
RECYCLEZ Avertissement Recy clez
correctement, ne les jetez pas dans une
déchetterie quelconque!
INFORMACIÓN WEEE
Este producto cumple todos los requisitos de
la Directiva de la UE sobre residuos de equipos
eléctricos y electrónicos. Este producto debe
reciclarse adecuadamente. Puede desmontarse para
facilitar el adecuado reciclado de cada una de sus
piezas. Consulte a su distribuidor o al organismo
público pertinente acerca de los puntos limpios para
la recogida de residuos de equipos eléctricos y
electrónicos.
SÍMBOLOS DE ADVERTENCIA
RECICLADO ¡Advertencia! ¡Siga las indicaciones
de reciclado adecuadas, no deseche el
producto con los residuos habituales!
INFORMAZIONI SU WEEE
Questo dispositivo è conforme a tutti i requisiti della
direttiva UE (WEEE) sullo smaltimento di apparecchiature
elettriche ed elettroniche. Questo prodotto deve
essere riciclato correttamente e può essere smontato
per agevolare il riciclaggio dei singoli componenti. Per
informazioni sui punti di raccolta WEEE, consultare il
rivenditore o l’autorità preposta.
SIMBOLI DI AVVERTENZA
RICICLAGGIO Avvertenza: riciclare
correttamente, non buttare con i rifiuti ordinari.
WEEE INFORMASJON
Dette produktet tilfredsstiller alle krav i EU direktivet
2002/96/EC som gjelder brukt elektrisk og elektronisk
utstyr. Dette produktet skal resirkuleres forsvarlig. Det
kan demonteres slik at de enkelte deler kan resirkuleres
forsvarlig. Ta kontakt med en forhandler eller relevant
offentlig myndighet angående oppsamlingssteder for
oppsamling av WEEE.
SYMBOLER
RESIRKULER Advarsel! Resirkuler som
spesialavfall. Må ikke kastes i vanlig avfall!
english
deutsch
francais
español
italiano
norsk
  • Page 1 1
  • Page 2 2

Barco X-PORT DCC 120 Quick start guide

Barco
Brand
Barco
Model
X-PORT DCC 120
Type
Quick start guide
This manual is also suitable for

Barco X-PORT DCC 120 is a module that adds extra capabilities to your projector. Once the device is inserted, it enables you to project 3D content to your audience in multiple ways.

The device offers support for both dual input 3D and double flash 3D. This means that you can connect two separate sources (such as a Blu-ray player and a game console) to the projector and display 3D content from both sources simultaneously. Alternatively, you can connect a single source that supports double flash 3D, and the projector will convert the signal to a standard 3D feed.

The X-PORT DCC 120 is easy to install. Simply locate the X-PORT connector on your projector and press the module into place. The four retainer screws will keep the module securely fastened.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents