Schlage BE375 Installation guide

BE375
Schlage
Brand
Schlage
Model
BE375
Type
Installation guide
*P516-865*
P516-865
Prepare for Installation
Tools Needed
• Phillips screwdriver
• Tape Measure
• Pencil
Optional
• Flathead Screwdriver
• Wood Block
• Hammer
IMPORTANT NOTES
DO NOT use a power drill for installation!
• Install and test lock with door open to avoid being locked out.
• If tailpiece is not installed,
insert into slot on the back of
the touchscreen and snap into
place.
A Check door dimensions.
See consumer.schlage.com/Service-Support for door preparation
instructions if dimensions are different.
2³⁄₄" (70 mm)
OR
2
³⁄₈" (60 mm)
1" (25 mm)
Door Edge
2¹⁄₈" (53 mm)
Hole
5¹⁄₂" (140 mm)
Minimum
B Adjust bolt length, if necessary.
Measure the dimension shown. If the measurement is 2C\v” (70 mm),
extend the bolt.
2³⁄₈" (60 mm)
OR
2³⁄₄" (70 mm)
No adjustment needed. Rotate faceplate
180° to extend.
Extended
Model BE375
Keyless Touchscreen Deadbolt
Installation Instructions
Alternate Faceplate
C Change faceplate, if necessary.
Choose the drawing that matches your door edge.
Door Edge
No change necessary.
OR
Door Edge
Install Lock
1 Install the bolt.
OR
Wood Block
(Not Included)
Actual Size
CAUTION
Bolt must remain retracted
throughout installation!
Retracted Extended
2 Install the touchscreen on the outside of the door.
Slide tailpiece through the slot in the bolt, and route wire over bolt.
3 Install the thumbturn assembly.
3a Rotate the thumbturn to a vertical position.
3b Remove the battery cover.
3c Route battery cable from the touchscreen through
the hole in the thumbturn assembly.
3d Place thumbturn assembly against the door and
secure with two (2) screws.
3e Connect the wires.
4 Install the included battery.
IMPORTANT
Route the battery wire so it won’t be pinched
by the cover!
4a Install the battery cover. Do not pinch the wires!
5 Install reinforcement plate and strike into door jamb.
1¹⁄₈"
(29 mm)
2³⁄₄"
(70 mm)
1"
(25 mm)
¹⁄₈" (3 mm)
Pilot Hole
¹⁄₈" (3 mm)
3" (76 mm) Deep
1¹⁄₂" (38 mm)
1" (25 mm)
Deep
Strike Cut-Out (not to scale)
Rotate 180˚
if door stop is
on le side.
For maximum
security, install
reinforcement
plate.
Actual Size
Actual Size
Door Stop
Actual Size
© Allegion 2014
Printed in U.S.A.
P516-865 Rev. 06/14-b
Test Lock
a Extend the bolt (lock).
1. Press
Schlage.
2. Rotate the
thumbturn toward
door edge.
Did bolt extend?
Yes. Lock is
installed correctly.
No. Lock is not installed correctly.
Check steps 3e and 4 and try
again.
b Retract the bolt (unlock).
IMPORTANT
Press Schlage and rotate thumbturn away from the door edge. If the
bolt retracts, the lock is not installed correctly. Pay attention to step
3a and try again.
1. Find User Code A on the
Schlage Touch™
User Guide.
2. Enter User Code A (four
digits) into the keypad.
Did bolt retract?
Yes . Lock is
installed correctly.
No. Verify that the right user
code was entered. If the user
code is correct, check step 4 and
try again.
3. Rotate thumbturn away
from door edge.
Program Lock
See the Schlage Touch™ User Guide that came with this lock.
Go to schlage.com for videos and more. Register your product at
RegisterMySchlage.com.
Lifetime Limited Mechanical and Finish Warranty and 3-Year Limited Electronics
Warranty
Subject to the terms and conditions of this warranty, Schlage extends a lifetime limited
mechanical and finish warranty and a three-year limited electronics warranty to the original
consumer user (“Original User”) of our Schlage brand product (“Product”) against defects in
material and workmanship, as long as the Original User occupies the residential premises upon
which the Product was originally installed.
What Schlage will do: Upon return of the defective Product to Schlage, Schlage’s sole
obligation, at its option, is to either repair or replace the Product, or refund the original purchase
price in exchange for the Product.
Original User: This warranty only applies to the Original User of Products. This warranty is not
transferable.
What is not covered: The following costs, expenses and damages are not covered by the
provisions of this limited Warranty: (i) labor costs including, but not limited to, such costs
as the removal and reinstallation of Product; (ii) shipping and freight expenses required to
return Product to Schlage; and (iii) any other incidental, consequential, indirect, special and/
or punitive damages, whether based on contract, warranty, tort (including, but not limited to,
strict liability or negligence), patent infringement, or otherwise, even if advised of the possibility
of such damages. Some local laws do not allow the exclusion or limitation of incidental or
consequential damages, so the above exclusion or limitation may not apply to you.
The provisions of this warranty do not apply to Products: (i) used in commercial
applications; (ii) used in common area applications; (iii) used for purposes for which they
are not designed or intended; (iv) which have been subjected to alteration, abuse, misuse,
negligence or accident; (v) which have been improperly stored, installed, maintained or
operated; (vi) which have been used in violation of written instructions provided by Schlage;
(vii) which have been subjected to improper temperature, humidity or other environmental
conditions; or (viii) which, based on Schlage’s examination, do not disclose to Schlage’s
satisfaction non- an implied warranty lasts, so that the above limitations may not fully apply.
Refer to your local laws for your specific rights under this warranty.
Guaranteed Fit Program: Schlage products are designed to fit standard residential door
preparations and retrofit existing tubular locks. Note: Mortise locks and preparations are not
considered standard and are not guaranteed under this program.
During the initial installation, if there is a problem with the Product’s performance, the Original
User may simply contact Schlage Customer Service at 888-805-9837 in the U.S. and Canada
or 800-506-7866 in Mexico for assistance.Program and warranty claims: If you encounter a
residential door preparation or fit issue under the Guaranteed Fit Program or have a claim under
this warranty, please contact Schlage Customer Service for repair, replacement or refund of the
original purchase price in exchange for the return of the Product to Schlage.
Schlage Customer Service
Calling From:
U.S.A.: (888) 805-9837
Canada: (800) 997-4734
Mexico: 018005067866
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Schlage BE375 Installation guide

BE375
Schlage
Brand
Schlage
Model
BE375
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents