American Standard 0451.021.020 User manual

Type
User manual

This manual is also suitable for

M17
© 2008 AS America Inc.
Revised 2/08
To Be Specied:
Color: White Bone Silver Linen
Black
Faucet*:
Faucet Finish:
Supplies with Stop:
1-1/4" Trap:
Nipple:
* See faucet section for additional models available
CORNER MINETTE™
WALL-HUNG LAVATORY
VITREOUS CHINA
CORNER MINETTE™ WALL-HUNG LAVATORY
Wall-hung corner sink
Vitreous china
Front overow
Supplied with 2 wall hangers
Faucet ledge
Shown with 2000.101 Ceramix faucet
(not included)
0451.021 Faucet holes on 102mm (4") centers
0451.001 Single center faucet hole
Nominal Dimensions:
279 x 425mm
(11" x 16-3/4")
Bowl sizes:
311mm (12-1/4") wide,
219mm (8-5/8") front to back,
133mm (5-1/4") deep
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A112.19.2 for Vitreous China Fixture
SEE REVERSE FOR ROUGHING-IN DIMENSIONS
M18
© 2008 AS America Inc.
CORNER MINETTE™
WALL-HUNG LAVATORY
VITREOUS CHINA
FINISHED
FLOOR
SUPPLIES
AS REQ'D.
464mm
(18-1/4)
*
178mm
(7-1/2)
165mm
(6-1/2)
279mm
(11)
165mm
(6-1/2)
152mm
(6)
127mm
(5)
102mm
(4)
127mm
(5)
425mm
(16-3/4)
C/L OF C.W. SUPPLY
C/L OF WASTE
C/L OF HANGER
FINISHED WALL
(2)19mm(3/8) DIA. ANCHOR SCREW
HOLES IN BACK DRAPERY
HANGER
260mm
(10-1/4)
*
178mm
(7)
178mm
(7)
787mm
(31)
108mm
(4-1/4)
1-1/4 O.D WASTE
1-1/4 O.D. TAILPIECE
C/L OF HANGER
C/L OF H.W. SUPPLY
FINISHED
FLOOR
SUPPLIES
AS REQ'D.
464mm
(18-1/4)
*
178mm
(7-1/2)
165mm
(6-1/2)
279mm
(11)
165mm
(6-1/2)
152mm
(6)
127mm
(5)
425mm
(16-3/4)
C/L OF C.W. SUPPLY
C/L OF WASTE
C/L OF HANGER
FINISHED WALL
(2)19mm(3/8) DIA. ANCHOR SCREW
HOLES IN BACK DRAPERY
HANGER
260mm
(10-1/4)
*
178mm
(7)
178mm
(7)
787mm
(31)
108mm
(4-1/4)
1-1/4 O.D WASTE
1-1/4 O.D. TAILPIECE
C/L OF HANGER
C/L OF H.W. SUPPLY
0451.021 4" CENTER FAUCET HOLES
0451.001 CENTER HOLE FAUCET
NOTES:
*
DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P” TRAP
ARE SUGGESTED.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
IMPORTANT: Dimensions of xtures are nominal and may vary within
the range of tolerances established by ANSI Standard A112.19.2. These
measurements are subject to change or cancellation. No responsibility is
assumed for use of superseded or voided pages.
Revised 2/08
  • Page 1 1
  • Page 2 2

American Standard 0451.021.020 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI