Electro-Voice Xlvc-TAE Operating instructions

Electro-Voice
Brand
Electro-Voice
Model
Xlvc-TAE
Type
Operating instructions

Electro-Voice Xlvc-TAE is a tilt-angle extender bar that allows a single column composed of an X-Line Very Compact Grid and Loudspeaker Array to be flown and tilted to obtain desired sound coverage. It offers up to 18 different angle positions either in declination or inclination depending on how the bar is positioned on the grid. The Xlvc-TAE has a maximum array height of 100 in. (2.54 m) when tilting down and a maximum array weight of 600 lbs (272 kg) when using hole positions 7-18. It is designed for use with XLVC-Series grids and XLD281/XLD291, XLE181/XLE191, and XS212 loudspeakers.

Electro-Voice Xlvc-TAE is a tilt-angle extender bar that allows a single column composed of an X-Line Very Compact Grid and Loudspeaker Array to be flown and tilted to obtain desired sound coverage. It offers up to 18 different angle positions either in declination or inclination depending on how the bar is positioned on the grid. The Xlvc-TAE has a maximum array height of 100 in. (2.54 m) when tilting down and a maximum array weight of 600 lbs (272 kg) when using hole positions 7-18. It is designed for use with XLVC-Series grids and XLD281/XLD291, XLE181/XLE191, and XS212 loudspeakers.

XLVC-TAE
X-Line Very Compact
Tilt-Angle Extender Bar
User Instructions
Tilt-Angle Extender Bar
The X-Line Very Compact Tilt-Angle Extender Bar features a rigging attachment position to allow a single column composed of an X-Line
Very Compact Grid and Loudspeaker Array to be flown and tilted to obtain desired sound coverage. The X-Line Very Compact Tilt-Angle
Extender Bar offers up to 18 different angle positions either in declination or inclination depending on how the bar is positioned on the
grid.
Figure 1:
Attaching Grid to Tilt-Angle Extender Bar
Grid
Tilt-Angle
Extender Bar
Detent Pin
Detent Pin
Figure 2:
Tilt-Angle Extender Bar Shipping/Transport Configuration
Store Shackle on
Pin during Shipping
and Transportation
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
12000 Portland Avenue South, Burnsville, MN 55337
Phone: 952/884-4051, Fax: 952/884-0043
www.electrovoice.com
© Bosch Communications Systems 11/2007
Part Number LIT000119 Rev A
U.S.A. and Canada only. For customer orders, contact Customer Service at:
800/392-3497 Fax: 800/955-6831
Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:
+ 49 9421-706 0 Fax: + 49 9421-706 265
Other Internatonal locations. For customer orders, Contact Customer Service at:
+ 1 952 884-4051 Fax: + 1 952 887-9212
For warranty repair or service information, contact the Service Repair department at:
800/685-2606
For technical assistance, contact Technical Support at: 866/78AUDIO
Specifications subject to change without notice.
Electro-Voice
®
Figure 3:
Tilt-Angle Extender Bar Declination and Incli-
nation with Attached Grid and Loudspeakers
100 in.
(2.54 m)
MAX
MAXIMUM
ARRAY HEIGHT:
Measured from
hole position used
to bottom of array.
Tilting Down
(Hole #1 at Rear)
Tilting Up
(Hole #1 at Front)
MAXIMUM ARRAY WEIGHT
XLVC GRID AND ALL BOXES BELOW
Hole Positions Maximum Allowable Weight of Array
1-2 400 lbs (181 kg)
3-4 480 lbs (218 kg)
5-6 560 lbs (254 kg)
7-18 600 lbs (272 kg)
Simplified Rigging-Rating Guidelines
1. These simplified rigging-rating guidelines provide ratings for
typical arrays based on the:
A. The total weight of the grid and all enclosures suspended
below the XLVC-TAE.
B. The pick-up hole on the XLVC-TAE.
C. The total height of the array from the pick-up hole in the XLVC-
TAE to the bottom of the bottom loudspeaker.
D. The assumption that one pick-up point will be used.
Determining the forces throughout an array requires complex calculations.
These guidelines eliminate the need for weight-distribution calculations by
using conservative working-load ratings. Other array configurations may
be permissable – Consult the XLVC Users Guide and LAPS Software.
2. Never exceed the weight limit for any XLVC-TAE pick-up hole.
3. Never exceed the height limit for any array using the XLVC-TAE.
4. Make sure that the two quick-release pins that secure the
spreader bars on the grid to the XLVC-TAE are fully locked.
5. Do not remove any bolts or dissasemble the XLVC-TAE.
6. Only use Electro-Voice rigging hardware.
7. Only suspend using the XLVC-Series grids.
8. Read the XLVC Users Guide before suspending any loud
speakers overhead.
9. All non-Electro-Voice hardware is the responsibility of others.
TYPICAL ARRAY LIMITS
MAXIMUM NUMBER OF XLVC BOXES
Hole Positions XLD281/
XLD291
XLE181/
XLE191
XS212
1-2 8 9 4
3-4 9 10 5
5-6 10 12 6
7-18 12 12 6
Simplified Rigging Structural Ratings
  • Page 1 1
  • Page 2 2

Electro-Voice Xlvc-TAE Operating instructions

Electro-Voice
Brand
Electro-Voice
Model
Xlvc-TAE
Type
Operating instructions

Electro-Voice Xlvc-TAE is a tilt-angle extender bar that allows a single column composed of an X-Line Very Compact Grid and Loudspeaker Array to be flown and tilted to obtain desired sound coverage. It offers up to 18 different angle positions either in declination or inclination depending on how the bar is positioned on the grid. The Xlvc-TAE has a maximum array height of 100 in. (2.54 m) when tilting down and a maximum array weight of 600 lbs (272 kg) when using hole positions 7-18. It is designed for use with XLVC-Series grids and XLD281/XLD291, XLE181/XLE191, and XS212 loudspeakers.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents