Electro-Voice Xlc-TAE Operating instructions

Electro-Voice
Brand
Electro-Voice
Model
Xlc-TAE
Category
Soundbar speakers
Type
Operating instructions

Electro-Voice Xlc-TAE is a Tilt-Angle Extender Bar designed to allow a single column of an X-Line Compact Grid and Loudspeaker Array to be flown and tilted to obtain the desired sound coverage. It offers up to 16 different angle positions in either declination or inclination, depending on positioning on the grid. The Xlc-TAE has a rigging attachment position and simplified rigging-rating guidelines to help users determine the maximum array weight, height, and number of XLC boxes that can be used.

Electro-Voice Xlc-TAE is a Tilt-Angle Extender Bar designed to allow a single column of an X-Line Compact Grid and Loudspeaker Array to be flown and tilted to obtain the desired sound coverage. It offers up to 16 different angle positions in either declination or inclination, depending on positioning on the grid. The Xlc-TAE has a rigging attachment position and simplified rigging-rating guidelines to help users determine the maximum array weight, height, and number of XLC boxes that can be used.

XLC-TAE
X-Line Compact
Tilt-Angle Extender Bar
User Instructions
Tilt-Angle Extender Bar
The X-Line Compact Tilt-Angle Extender Bar features a rigging attachment position to allow a single column composed of an X-Line
Compact Grid and Loudspeaker Array to be flown and tilted to obtain desired sound coverage. The X-Line Compact Tilt-Angle Extender
Bar offers up to 16 different angle positions either in declination or inclination depending on how the bar is positioned on the grid.
Figure 1:
Attaching Grid to Tilt-Angle Extender Bar
Grid
Tilt-Angle
Extender Bar
Detent Pin
Detent Pin
Figure 2:
Tilt-Angle Extender Bar Shipping/Transport Configuration
Store Shackle on
Pin during Shipping
and Transportation
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
12000 Portland Avenue South, Burnsville, MN 55337
Phone: 952/884-4051, Fax: 952/884-0043
www.electrovoice.com
© Bosch Communications Systems 11/2007
Part Number LIT000120 Rev A
U.S.A. and Canada only. For customer orders, contact Customer Service at:
800/392-3497 Fax: 800/955-6831
Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:
+ 49 9421-706 0 Fax: + 49 9421-706 265
Other Internatonal locations. For customer orders, Contact Customer Service at:
+ 1 952 884-4051 Fax: + 1 952 887-9212
For warranty repair or service information, contact the Service Repair department at:
800/685-2606
For technical assistance, contact Technical Support at: 866/78AUDIO
Specifications subject to change without notice.
Electro-Voice
®
Figure 3:
Tilt-Angle Extender Bar Declination and Incli-
nation with Attached Grid and Loudspeakers
100 in.
(2.54 m)
MAX
MAXIMUM
ARRAY HEIGHT:
Measured from
hole position used
to bottom of array.
Tilting Down
(Hole #1 at Rear)
Tilting Up
(Hole #1 at Front)
MAXIMUM ARRAY WEIGHT
XLC GRID AND ALL BOXES BELOW
Hole Positions Maximum Allowable Weight of Array
1-2 670 lbs (304 kg)
3-4 780 lbs (354 kg)
5-16 900 lbs (408 kg)
Simplified Rigging-Rating Guidelines
1. These simplified rigging-rating guidelines provide ratings for
typical arrays based on the:
A. The total weight of the grid and all enclosures suspended
below the XLC-TAE.
B. The pick-up hole on the XLC-TAE.
C. The total height of the array from the pick-up hole in the XLC-
TAE to the bottom of the bottom loudspeaker.
D. The assumption that one pick-up point will be used.
Determining the forces throughout an array requires complex calculations.
These guidelines eliminate the need for weight-distribution calculations by
using conservative working-load ratings. Other array configurations may
be permissable – Consult the XLC Users Guide and LAPS Software.
2. Never exceed the weight limit for any XLC-TAE pick-up hole.
3. Never exceed the height limit for any array using the XLC-TAE.
4. Make sure that the two quick-release pins that secure the
spreader bars on the grid to the XLC-TAE are fully locked.
5. Do not remove any bolts or dissasemble the XLC-TAE.
6. Only use Electro-Voice rigging hardware.
7. Only suspend using the XLC-Series grids.
8. Read the XLC Users Guide before suspending any loud
speakers overhead.
9. All non-Electro-Voice hardware is the responsibility of others.
TYPICAL ARRAY LIMITS
MAXIMUM NUMBER OF XLC BOXES
Hole Positions
XLC127, XLC127+,
XLC127DVX,
XLC907DVX
XLC118,
XLC215
1-2 6 4
3-4 7 5
5-16 8 6
Simplified Rigging Structural Ratings
  • Page 1 1
  • Page 2 2

Electro-Voice Xlc-TAE Operating instructions

Electro-Voice
Brand
Electro-Voice
Model
Xlc-TAE
Category
Soundbar speakers
Type
Operating instructions

Electro-Voice Xlc-TAE is a Tilt-Angle Extender Bar designed to allow a single column of an X-Line Compact Grid and Loudspeaker Array to be flown and tilted to obtain the desired sound coverage. It offers up to 16 different angle positions in either declination or inclination, depending on positioning on the grid. The Xlc-TAE has a rigging attachment position and simplified rigging-rating guidelines to help users determine the maximum array weight, height, and number of XLC boxes that can be used.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents