Kohler K-P8304-PS-NA Dimensions Guide

Kohler
Brand
Kohler
Model
K-P8304-PS-NA
Category
Faucets
Type
Dimensions Guide

Kohler K-P8304-PS-NA is a complete valve body and cartridge kit for use in standard, back to back and thin wall installations. It includes a valve body, pressure balance cartridge, rough-in guide and mud guard. The 1/2" PEX Crimp (F1807 style) inlets with stops and 1/2" Universal NPT & direct sweat outlets make it easy to install. The service stops include integral check valves, and the 5.0 gpm (18.9 l/min) maximum flow rate at 45 psi ensures a powerful and consistent water flow. The single lever design cycles from off through cold to hot, providing precise temperature control.

Kohler K-P8304-PS-NA is a complete valve body and cartridge kit for use in standard, back to back and thin wall installations. It includes a valve body, pressure balance cartridge, rough-in guide and mud guard. The 1/2" PEX Crimp (F1807 style) inlets with stops and 1/2" Universal NPT & direct sweat outlets make it easy to install. The service stops include integral check valves, and the 5.0 gpm (18.9 l/min) maximum flow rate at 45 psi ensures a powerful and consistent water flow. The single lever design cycles from off through cold to hot, providing precise temperature control.

Features
•
Project Pack: Supplied 12 per case.
•
Includes valve body, pressure balance cartridge, rough-in guide
and mud guard.
•
1/2" PEX Crimp (F1807 style) inlets, with stops.
•
1/2" Universal NPT & direct sweat outlets.
•
Service stops include integral check valves.
•
5.0 gpm (18.9 l/min) maximum flow rate at 45 psi.
•
Single lever design cycles from off through cold to hot.
•
Provides temperature regulation and automatic anti-scald
protection.
•
One piece cartridge design simplifies installation and
maintenance.
Codes/Standards
•
Adjustable high temperature limit stop to control maximum water
temperature.
ASME A112.18.1/CSA B125.1
•
Requires valve trim to complete installation (sold separately).
ASSE 1016/ASME A112.1016/CSA B125.16
Material
KOHLER
®
Faucet Lifetime Limited
Warranty
•
Forged De-zincification Resistant Brass body provides long
term reliability and resistance to aggressive water conditions.
See website for detailed warranty information.
Technology
•
Pressure-balancing diaphragm technology maintains outlet
temperature within +/- 3 degrees Fahrenheit during water
pressure fluctuations.
Installation
•
Designed for use in standard, back to back and thin wall
installations.
•
Valve body features integral mounting locations and symmetrical
valve inlets to simplify installation.
•
Cartridge is reversible for installations where hot and cold
supplies are reversed.
•
Rough-in guide designed for both standard and thin wall
installations.
•
Installed valve rough-in can be flushed and pressure tested to
150psi max (air or water) without cartridge, using K-10351 Test
Cap.
Optional Accessories
K-10350 Deep Rough-In Kit For K-8305 Cartridges
K-10351 Test Cap For K-8300 Series Valve Bodies
1-800-4KOHLER (1-800-456-4537)
Kohler Co. reserves the right to make revisions without notice to product specifications.
For the most current Specification Sheet, go to www.kohler.com.
9-28-2018 16:11
Rite-Temp
®
Valve Body & Cartridge Kit Complete
K-P8304-PS
2-15/16"
Notes
Technical Information
Install this product according to the installation
guide.
All product dimensions are nominal.
Shower Valve:
Avoid cross-flow conditions. Do not install a
shut-off device on either valve outlet.
20 psi (1.4 bar)Min. pressure IN:
Machined-brassValve body:
Cap the shower outlet if the deck-mounted spout,
diverter, or handshower is connected to the spout
outlet.
Install straight pipe or tube drop of 7" (178 mm)
to 18" (457 mm) with single elbow between the
valve and the wall-mount spout.
For finished walls greater than 3/4" (19 mm) and
less than 1-1/2" (38 mm), install support(s) 2" (51
mm) from the stud face.
For finished walls greater than 1-1/2" (38 mm),
install support(s) 3" (76 mm) from the face of the
finished wall.
1-800-4KOHLER (1-800-456-4537)
Kohler Co. reserves the right to make revisions without notice to product specifications.
For the most current Specification Sheet, go to www.kohler.com.
9-28-2018 16:11
Rite-Temp
®
Valve Body & Cartridge Kit Complete
K-P8304-PS
  • Page 1 1
  • Page 2 2

Kohler K-P8304-PS-NA Dimensions Guide

Kohler
Brand
Kohler
Model
K-P8304-PS-NA
Category
Faucets
Type
Dimensions Guide

Kohler K-P8304-PS-NA is a complete valve body and cartridge kit for use in standard, back to back and thin wall installations. It includes a valve body, pressure balance cartridge, rough-in guide and mud guard. The 1/2" PEX Crimp (F1807 style) inlets with stops and 1/2" Universal NPT & direct sweat outlets make it easy to install. The service stops include integral check valves, and the 5.0 gpm (18.9 l/min) maximum flow rate at 45 psi ensures a powerful and consistent water flow. The single lever design cycles from off through cold to hot, providing precise temperature control.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents