GND
STRAP AND MOUNTING SCREWS
#2 BLACK WIRE = –6 VDC
RIBBED WIRE =
–6 VDC
#1 BLACK WIRE =
+6 VDC
SMOOTH WIRE =
+6 VDC
WIRE NUT
WIRES
TOGETHER
BOX AND WIRING TO BE SUPPLIED BY CUSTOMER
20 FOOT MAXIMUM LENGTH PER FAUCET.
10 FOOT CABLE AND CONNECTOR
ASSEMBLY SUPPLIED WITH EACH FAUCET
AS STANDARD.
–
+
S-6240 POWER SUPPLY for use with up to eight (8) S-6080-ACM ULTRA-SENSE® FAUCETS
INPUT: 100 - 240VAC 47-63 Hz @ 1.35A
OUTPUT: 6 V DC @ 7A
SYMMONS INDUSTRIES, INC., 31 Brooks Drive, Braintree, Massachusetts 02184-3804
Tel: 1-800-SYMMONS, (800) 796-667 Fax: 1-800-961-9621
Website: www.symmons.com
© 2004-2015 Symmons Industries, Inc ZV-488 010815
S-6080-ACM - Multiple Faucet Electrical Installation
The 120 VAC to 6 volt DC power supply for multiple faucet installations must
be mounted in a termination box and terminated in accordance with state
and local electrical codes. A licensed electrician must provide a 120 volt AC
power source to the termination box.
1. Install the faucet per Ultra-sense AC powered, Sensor Faucet S-6080-AC and ACM
Installation Instructions.
2. The maximum allowable faucets the S-6240 power supply can handle is eight (8).
3. A 10 foot cable and connector is supplied with each S-6080-ACM faucet. 20 foot
cable length available (part no. SF-193A purchased and supplied separately).
4. The installer may choose to purchase an electrical termination box from an
electrical distributor or use the Symmons termination box (part no. S-6244
purchased and supplied separately). Reference supplies dimensional
requirements, found on the submittal sheet.
5. Mount the termination box to a wall, under the sink or in an adjacent closet
ensuring that the furthest faucet is within nineteen feet of the termination box.
6. Plug the cable receptacle end into the faucet cable plug (see figure 2) by aligning
the raised rib of the cable receptacle with the raised rib of the faucet plug. Push
them together evenly until the ribs meet. Avoid bending the internal pins.
7. Run the cable under the sink to the termination box. Secure it in accordance with
State and local electrical codes. Avoid contact with water pipes. Repeat this
procedure for each faucet.
8. Bring the wires to the box through a strain relief connector and strip off six to
eight inches of the wire jacket so the wires are exposed. Strip the ends of
each wire.
9. Cut the DC output cord to about eight to ten inches.
10. Pull the two DC wires apart and strip the ends. Connect all the faucet’s #2 black
wires (-) to the smooth DC wire (-) and the facuet’s #1 black wires (+) to the
striped DC wire (+). Use wire nuts to secure wires.
11. Connect the AC power cord end of the power supply to the 120VAC power line
supplied to the box by a licensed electrician.
12. Faucets may all activate for one cycle on initial power up.
SIDE VIEW
FIGURE 2
TOP VIEW
MATED CONNECTORS
-
1
Symmons S-6240 Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Symmons S-6080-AC-12V-SSUP-G-0.35 Installation guide
-
-
-
-
Fortis S-248-2-STN-LAM-1.5 Installation guide
-
-
-
-
Symmons SLW-4512-1.5 Installation guide
-
Symmons S-240-2-LWG-1.0 Installation guide