Hitachi G 13SN Safety Instructions And Operation Manual

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce

produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs et propriétaires

avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être conservé dans un

endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede

resultar en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este

manual debe ser guardado en un lugar seguro.

DOUBLE INSULATION

DOUBLE ISOLATION

AISLAMIENTO DOBLE

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read and

understand this manual BEFORE operating the power tool. Please keep this manual

available for other users and owners before they use the power tool.

This manual should be stored in safe place

G12SN

G 10SN • G 12SN • G 13SN

Model Disc Grinder

Modèle Meuleuse à disque

Modelo Amoladora angular

00Cover_G10SN_US 8/10/10, 13:311

Page is loading ...

English

3

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual

before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic

safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation

before it occurs, and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by WARNINGS on the

power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate

injury, or may cause machine damage.

NOTE emphasizes essential information.

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WARNING:

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust.

Power tools create sparks which may ignite

the dust or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodified plugs and matching outlets will

reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the

risk of electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts.

Damaged or entangled cords increase the risk

of electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the influence of drugs, alcohol or

medication.

01Eng_G10SN_US 12/25/12, 7:34 AM3

English

4

A moment of inattention while operating

power tools may result in serious personal

injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing

protection used for appropriate conditions

will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool.

Carrying power tools with your finger on the

switch or energising power tools that have

the switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating

part of the power tool may result in personal

injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool

in unexpected situations.

f) Dress properly. Do not wear loose clothing

or jewellery. Keep your hair, clothing and

gloves away from moving parts.

Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities,

ensure these are connected and properly

used.

Use of dust collection can reduce dust-related

hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better

and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and off.

Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the

risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation.

If damaged, have the power tool repaired

before use.

Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations different

from those intended could result in a

hazardous situation.

5) Service

a) Have your power tool serviced by a qualified

repair person using only identical

replacement parts.

This will ensure that the safety of the power

tool is maintained.

SAFETY WARNINGS COMMON FOR

GRINDING OPERATIONS

a) This power tool is intended to function as a grinder.

Read all safety warnings, instructions, illustrations

and specifications provided with this power tool.

Failure to follow all instructions listed below may

result in electric shock, fire and/or serious injury.

b) Operations such as sanding, wire brushing or

polishing or cutting-off are not recommended to be

performed with this power tool.

Operations for which the power tool was not

designed may create a hazard and cause personal

injury.

c) Do not use accessories which are not specifically

designed and recommended by the tool

manufacturer.

Just because the accessory can be attached to your

power tool, it does not assure safe operation.

d) The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool.

Accessories running faster than their rated speed

can break and fly apart.

e) The outside diameter and the thickness of your

accessory must be within the capacity rating of your

power tool.

Incorrectly sized accessories cannot be adequately

guarded or controlled.

f) The arbour size of wheels, flanges, backing pads or

any other accessory must properly fit the spindle of

the power tool.

01Eng_G10SN_US 8/10/10, 13:314

English

5

Accessories with arbour holes that do not match the

mounting hardware of the power tool will run out

of balance, vibrate excessively and may cause loss

of control.

g) Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for

chips and cracks, backing pad for cracks, tear or

excess wear, wire brush for loose or cracked wires.

If power tool or accessory is dropped, inspect for

damage or install an undamaged accessory. After

inspecting and installing an accessory, position

yourself and bystanders away from the plane of the

rotating accessory and run the power tool at

maximum no-load speed for one minute.

Damaged accessories will normally break apart

during this test time.

h) Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron capable of

stopping small abrasive or workpiece fragments.

The eye protection must be capable of stopping

flying debris generated by various operations. The

dust mask or respirator must be capable of filtrating

particles generated by your operation. Prolonged

exposure to high intensity noise may cause hearing

loss.

i) Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment.

Fragments of workpiece or of a broken accessory

may fly away and cause injury beyond immediate

area of operation.

j) Hold power tool by insulated gripping surfaces only,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord.

Cutting accessory contacting a”live” wire may make

exposed metal parts of the power tool “live” and

shock the operator.

k) Position the cord clear of the spinning accessory.

If you lose control, the cord may be cut or snagged

and your hand or arm may be pulled into the

spinning accessory.

l) Never lay the power tool down until the accessory

has come to a complete stop.

The spinning accessory may grab the surface and

pull the power tool out of your control.

m) Do not run the power tool while carrying it at your

side.

Accidental contact with the spinning accessory could

snag your clothing, pulling the accessory into your

body.

n) Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside the housing

and excessive accumulation of powdered metal may

cause electrical hazards.

o) Do not operate the power tool near flammable

materials.

Sparks could ignite these materials.

p) Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in

electrocution or shock.

KICKBACK AND RELATED WARNINGS

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other

accessory. Pinching or snagging causes rapid stalling

of the rotating accessory which in turn causes the

uncontrolled power tool to be forced in the direction

opposite of the accessory’s rotation at the point of the

binding.

For example, if an abrasive wheel is snagged or pinched

by the workpiece, the edge of the wheel that is entering

into the pinch point can dig into the surface of the

material causing the wheel to climb out or kick out. The

wheel may either jump toward or away from the

operator, depending on direction of the wheel’s

movement at the point of pinching. Abrasive wheels

may also break under these conditions.

Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and can

be avoided by taking proper precautions as given below.

a) Maintain a firm grip on the power tool and position

your body and arm to allow you to resist kickback

forces. Always use auxiliary handle, if provided, for

maximum control over kickback or torque reaction

during start-up.

The operator can control torque reactions or kickback

forces, if proper precautions are taken.

b) Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

c) Do not position your body in the area where power

tool will move if kickback occurs.

Kickback will propel the tool in direction opposite to

the wheel’s movement at the point of snagging.

d) Use special care when working corners, sharp edges

etc. Avoid bouncing and snagging the accessory.

Corners, sharp edges or bouncing have a tendency

to snag the rotating accessory and cause loss of

control or kickback.

e) Do not attach a saw chain woodcarving blade or

toothed saw blade.

Such blades create frequent kickback and loss of

control.

SAFETY WARNINGS SPECIFIC FOR

GRINDING OPERATIONS

a) Use only wheel types that are recommended for

your power tool and the specific guard designed

for the selected wheel.

Wheels for which the power tool was not designed

cannot be adequately guarded and are unsafe.

01Eng_G10SN_US 8/10/10, 13:315

English

6

b) The guard must be securely attached to the power

tool and positioned for maximum safety, so the least

amount of wheel is exposed towards the operator.

The guard helps to protect operator from broken

wheel fragments and accidental contact with wheel.

c) Wheels must be used only for recommended

applications. For example: do not grind with the side

of cut-off wheel.

Abrasive cut-off wheels are intended for peripheral

grinding, side forces applied to these wheels may

cause them to shatter.

d) Always use undamaged wheel flanges that are of

correct size and shape for your selected wheel.

Proper wheel flanges support the wheel thus

reducing the possibility of wheel breakage. Flanges

for cut-off wheels may be different from grinding

wheel flanges.

e) Do not use worn down wheels from larger power

tools.

Wheel intended for larger power tool is not suitable

for the higher speed of a smaller tool and may burst.

GENERAL SAFETY INSTRUCTIONS FOR

GRINDERS

– Check that speed marked on the wheel is equal to

or greater than the rated speed of the grinder;

– Ensure that the wheel dimensions are compatible

with the grinder;

– Abrasive wheels shall be stored and handled with

care in accordance with manufacturer’s instructions;

– Inspect the grinding wheel before use, do not use

chipped, cracked or otherwise defective products;

– Ensure that mounted wheels and points are fitted in

accordance with the manufacturer’s instructions;

– Ensure that blotters are used when they are provided

with the bonded abrasive product and when they

are required;

– Ensure that the abrasive product is correctly

mounted and tightened before use and run the tool

at no-load for 30 s in a safe position, stop

immediately if there is considerable vibration or if

other defects are detected. If this condition occurs,

check the machine to determine the cause;

– If a guard is equipped with the tool never use the

tool without such a guard;

– Do not use separate reducing bushings or adapters

to adapt large hole abrasive wheels;

– For tools intended to be fitted with threaded hole

wheel, ensure that the thread in the wheel is long

enough to accept the spindle length;

– Check that the work piece is properly supported;

– Do not use cutting off wheel for side grinding;

– Ensure that sparks resulting from use do not create

a hazard e.g. do not hit persons, or ignite flammable

substances;

– Ensure that ventilation openings are kept clear when

working in dusty conditions, if it should become

necessary to clear dust, first disconnect the tool from

the mains supply (use non metallic objects) and

avoid damaging internal parts;

– Always use eye and ear protection. Other personal

protective equipment such as dust mask, gloves,

helmet and apron should be worn;

– Pay attention to the wheel that continues to rotate

after the tool is switched off.

SPECIFIC SAFETY RULES AND SYMBOLS

1. ALWAYS use proper guard with grinding wheel.

A guard protects operator from broken wheel

fragments.

2. Accessories must be rated for at least the speed

recommended on the tool warning label. Wheels

and other accessories running over rated speed

can fly apart and cause injury.

3. Hold tools by insulated gripping surfaces when

performing an operation where the cutting tool

may contact hidden wiring or its own cord. Contact

with a “live” wire will make exposed metal parts

of the tool “live” and shock the operator.

4. ALWAYS wear ear protectors when using the tool

for extended periods.

Prolonged exposure to high intensity

noise can cause hearing loss.

5. Use only a depressed center wheel with a rated

capacity which is GREATER than 13,700/min for

G10SN, 13,300/min for G12SN, 12,000/min for

G13SN. Using any wheel a rated capacity LESS

than 13,700/min for G10SN, 13,300/min for G12SN

and 12,000/min for G13SN and/or an incorrect sized

wheel (see SPECIFICATIONS at page 9) may result

in wheel breakage, flying wheel fragments, and

resulting in death or serious injury.

6. NEVER touch moving parts.

NEVER place your hands, fingers or

other body parts near the tool’s moving

parts.

7. NEVER operate without all guards in place.

NEVER operate this tool without all guards or

safety features in place and in proper working

order. If maintenance or servicing requires the

removal of a guard or safety feature, be sure to

replace the guard or safety feature before resuming

operation of the tool.

01Eng_G10SN_US 8/10/10, 13:316

English

7

8. Use right tool.

Don’t force small tool or attachment to do the job

of a heavy-duty tool.

Don’t use tool for purpose not intended —for

example— don’t use circular saw for cutting tree

limbs or logs.

9. NEVER use a power tool for applications other

than those specified.

NEVER use a power tool for applications other than

those specified in the Instruction Manual.

10. Handle tool correctly.

Operate the tool according to the instructions

provided herein. Do not drop or throw the tool.

NEVER allow the tool to be operated by children,

individuals unfamiliar with its operation or

unauthorized personnel.

11. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted.

Check their condition periodically.

12. Do not use power tools if the plastic housing or

handle is cracked.

Cracks in the tool’s housing or handle can lead to

electric shock. Such tools should not be used until

repaired.

13. Blades and accessories must be securely mounted

to the tool.

Prevent potential injuries to yourself or others.

Blades, cutting implements and accessories which

have been mounted to the tool should be secure

and tight.

14. Keep motor air vent clean.

The tool’s motor air vent must be kept clean so

that air can freely flow at all times. Check for dust

build-up frequently.

15. Operate power tools at the rated voltage.

Operate the power tool at voltages specified on its

nameplate.

If using the power tool at a higher voltage than

the rated voltage, it will result in abnormally fast

motor revolution and may damage the unit and

the motor may burn out.

16. NEVER use a tool which is defective or operating

abnormally.

If the tool appears to be operating unusually,

making strange noises, or otherwise appears

defective, stop using it immediately and arrange

for repairs by a Hitachi authorized service center.

17. NEVER leave tool running unattended. Turn power

off.

Don’t leave tool until it comes to a complete stop.

18. Carefully handle power tools.

Should a power tool be dropped or struck against

hard materials inadvertently, it may be deformed,

cracked, or damaged.

19. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon

tetrachloride, and alcohol may damage and crack

plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly

dampened with soapy water and dry thoroughly.

20. NEVER use a depressed center wheel which is

cracked or deformed or worn away (see the

MAINTENANCE AND INSPECTION section on page

12).

21. NEVER use the grinder in places where the sparks

generated by the grinder can cause explosion, such

as where flammable materials or gases are

present.

22. NEVER push in the push button while the spindle

is running.

23. ALWAYS wear eye protection that meets the

requirement of the latest revision of

ANSI Standard Z87.1.

24. ALWAYS wear a mask or respirator to protect

yourself from dust or potentially harmful particles

generated during the grinding operation.

25. ALWAYS firmly grip the body handle and side

handle while operating the grinder.

26. ALWAYS have a trial run before grinding

commence. (see Test the grinder before using on

page 10).

27. ALWAYS follow the instructions contained in this

manual when replacing the depressed center

wheel.

28. ALWAYS be careful with buried object such as an

underground wiring.

Touching these active wiring or electric cable with

this tool, you may receive an electric shock.

Confirm if there are any buried object such as

electric cable within the wall, floor or ceiling where

you are going to operate here after.

29. Definitions for symbols used on this tool

V ............... volts

.............. Alternating current

Hz ............. hertz

A ............... amperes

W .............. watt

n ............... rated speed

---/min ...... revolutions per minute

ø ............

wheel diameter

mm ........... millimeter

" ................ inches

............. Class II Construction

01Eng_G10SN_US 12/17/12, 1:47 PM7

English

8

DOUBLE INSULATION FOR SAFER

OPERATION

To ensure safer operation of this power tool, HITACHI

has adopted a double insulation design. “Double

insulation” means that two physically separated

insulation systems have been used to insulate the

electrically conductive materials connected to the power

supply from the outer frame handled by the operator.

Therefore, either the symbol “ ” or the words “Double

insulation” appear on the power tool or on the nameplate.

Although this system has no external grounding, you

must still follow the normal electrical safety precautions

given in this Instruction Manual, including not using the

power tool in wet environments.

To keep the double insulation system effective, follow

these precautions:

䡬

Only HITACHI AUTHORIZED SERVICE CENTER

should disassemble or assemble this power tool,

and only genuine HITACHI replacement parts

should be installed.

䡬

Clean the exterior of the power tool only with a

soft cloth moistened with soapy water, and dry

thoroughly.

Never use solvents, gasoline or thinners on plastic

components; otherwise the plastic may dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO OTHER USERS

AND

OWNERS OF THIS TOOL!

01Eng_G10SN_US 12/17/12, 1:47 PM8

English

9

FUNCTIONAL DESCRIPTION

NOTE:

The information contained in this Instruction Manual is designed to assist you in the safe operation and

maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safey

instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that differ from those on your

own power tool.

NAME OF PARTS

SPECIFICATIONS

Model G10SN G12SN G13SN

Motor Single-Phase Series Commutator Motor

Power Source Single-Phase 120 V AC 60 Hz

Current 7.4 A

Rated Speed 10,000/min

Wheel Size:

4" (100 mm) 4-1/2" (115 mm) 5" (125 mm)

external diam.

hole diam.

5/8" (16 mm) 7/8" (22.23 mm) 7/8" (22.23 mm)

Weight 3.5 lbs (1.6 kg)

Fig. 1

Gear cover

Push button

Switch

Housing

Depressed center wheel

Packing gland

Wheel guard

Tail cover

Side handle

01Eng_G10SN_US 12/17/12, 11:47 AM9

English

10

ASSEMBLY AND OPERATION

APPLICATIONS

䡬

Removal of casting fin and finishing of various type

of steel, bronze and aluminum materials and

castings.

䡬

Grinding of welded sections or sections cut by

means of an acetylene torch.

䡬

Grinding of synthetic resins, slate, brick, marble.

WARNING:

To avoid the risk of serious injury, NEVER use this

grinder with cup wheels and/or saw blades.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized

conforms to the power source requirements

specified on the product nameplate.

2. Power switch

Ensure that the switch is in the OFF position. If the

plug is connected to a receptacle while the switch

is in the ON position, the power tool will start

operating immediately and can cause serious injury.

3. Extension cord

When the work area is far away from the power

source, use an extension cord of sufficient

thickness and rated capacity. The extension cord

should be kept as short as practicable.

WARNING:

Damaged cord must be replaced or

repaired.

4. Check the receptacle

If the receptacle only loosely accepts the plug, the

receptacle must be repaired. Contact a licensed

electrician to make appropriate repairs.

If such a faulty receptacle is used, it may cause

overheating, resulting in a serious hazard.

5. Check your work environment

Ensure the following before operation;

䡬

No flammable gas, liquid, or object at

worksite.

䡬

When grinding thin steel sheet it may cause

a high booming noise.

To avoid such noise, place a rubber mat under

the workpiece.

䡬

Clear the area of children or unauthorized

personnel.

6. Mounting the wheel guard

Be sure to mount the wheel guard at an angle that

will protect the operator’s body from injury by a

broken wheel piece.

[Installing Wheel Guard]

䡬

Slightly loosen the screw on the wheel guard.

䡬

Install the wheel guard to the packing gland,

turn it to the angle suitable for operation, and

make adjustment.

䡬

After the adjustment, ensure that the screw

is securely tightened on the wheel guard in

order to fix it completely.

Fig. 2

WARNING:

If the wheel guard is not attached properly, a

broken wheel may result in and cause death or

serious injury.

7. Thoroughly check that the depressed center wheel

is free of cracks, splits and other abnormalities

before mounting. Make sure it is firmly clamped

and has been properly mounted. Refer to page 11

of this manual for Depressed Center Wheel

Assembly and Disassembly

8. Test the grinder before using.

Before actually beginning the grinding work, test

the grinder by first clearing the area of all other

personnel. Make sure the wheel guard is in place

and that you are wearing eye protection. Turn the

grinder “on”, and make sure the grinder runs

smoothly and shows no abnormalities.

Duration of the trial run is as follows:

When depressed center wheel is replaced

.......................................... 3 minutes or more

When starting daily work

............................................1 minute or more

Wheel guard

Packing gland

01Eng_G10SN_US 8/10/10, 13:3110

English

11

9. Use only properly rated depressed center wheels.

Use only depressed center wheels rated at

13,700/min for G10SN, 13,300/min for G12SN

12,000/min for G13SN or more.

Using a depressed center wheel rated less can lead

to wheel disintegration during operation and cause

serious bodily injury.

10. Check the push button.

Make sure that the push button is disengaged by

pushing push button two or three times before

turning on the grinder. (Fig. 5)

GRINDER OPERATION

1. Hold the grinder firmly by its housing and side

handle (Fig. 1).

The grinder produces a counterforce which must

be controlled by firmly holding onto the grinder.

2. Turn the grinder “on”. (Fig. 3)

While holding the grinder firmly, use one finger to

slide the switch to the “on” position.

Fig. 3

3. Use light grinding pressure.

There is no need to press hard when grinding.

Usually the grinder’s own weight is sufficient to

allow the required light contact with the surface to

be ground.

WARNING:

Do not press the grinder forcibly against the

surface to be ground. Heavy pressure can result

in wheel breakage and serious injury. It can also

damage the surface being ground or damage the

grinder’s motor.

4. Use proper grinding angle.

Grind only with the wheel’s edge by lifting the

grinder 15° to 30°, as shown in Fig. 4.

CAUTION:

Do not use the entire surface of the depressed

center wheel. Use only the edge of the depressed

center wheel.

5. Move the grinder in the proper direction.

When using a new depressed center wheel in

direction A (Fig. 4), the wheel edge may cut into the

workpiece. In this case, grind in direction B (Fig. 4).

Once the wheel edge is worn, the workpiece can be

ground in both directions.

Fig. 4

NOTE:

The wheel provided (resinoid wheel) is rated as

Class A grain and # 36 grain size for G10SN and

G12SN, # 24 grain size for G13SN. They are most

suitable for heavy grinding of steel and other types

of materials.

6. Adjust operation to desired finish.

For a fine finish, decrease pressure by lifting

slightly. Grind slowly and at the appropriate speed.

CAUTION:

The revolving depressed center wheel will create

air turbulence.

Do no lay the grinder down in areas of dust or dirt

until it has come to a complete stop.

DEPRESSED CENTER WHEEL ASSEMBLY

AND DISASSEMBLY

WARNING:

Never attempt to assemble or disassemble the

depressed center wheel, unless the power switch

is in the “OFF” position and the electrical cord has

been disconnected from the receptacle.

1. Assembly

(1) Turn the disc grinder upsidedown so that the

spindle is facing upward.

(2) Align the oval-shaped indentation of the wheel

washer with the notched part of the spindle, then

attach them.

(3) Fit the protuberance of the depressed center wheel

onto the wheel washer.

(4) Screw the wheel nut onto the spindle.

(5) While pushing the push button with one hand, lock

the spindle by turning the depressed center wheel

slowly with the other hand.

Tighten the wheel nut by using the supplied

wrench as shown in Fig. 5.

Switch

15° – 30°

ON

OFF

AB

01Eng_G10SN_US 8/10/10, 13:3111

English

12

CAUTION:

Tighten the wheel nut securely and confirm that

the depressed center wheel does not wobble.

2. Disassembly

To remove the depressed center wheel, simply

reverse the above-mentioned procedure.

MAINTENANCE AND INSPECTION

WARNING:

䢇

Be sure to switch power OFF and disconnect the plug from the receptacle during maintenance and inspection.

䢇

Using cracked, deformed or damaged wheels can lead to wheel breakage and resulting serious injury.

1. Replacing the depressed center wheel

Replace the depressed center wheel when it has been

worn out to about 2-3/8" (60mm) in external diameter.

Confirm that there is no crack or any damage to the

depressed center wheel. If there is a crack or a

transformation in the wheel, replace it immediately.

2. Inspecting the screws

Regularly inspect all screws and ensure that they

are fully tightened. Should any of the screws be

loosened, retighten them immediately.

WARNING:

Using this grinder with loosened screws is

extremely dangerous.

3. Confirm that there is no damage in the wheel

guard, the electrical cord and the housing, etc.

Check that the on/off switch operates normally.

4. Inspecting the carbon brushes

For your continued safety and electrical shock

protection, carbon brush inspection and

replacement on this tool should ONLY be performed

by a HITACHI AUTHORIZED SERVICE CENTER.

5. Replacing supply cord

If the supply cord of Tool is damaged, the Tool

must be returned to Hitachi Authorized Service

Center for the cord to be replaced.

Fig. 5

Wheel

nut

Wheel

guard

Push button

Wrench

Wheel

washer

Spindle

Depressed

center

wheel

6. Service and repairs

All quality power tools will eventually require

servicing or replacement of parts because of wear

from normal use. To assure that only authorized

replacement parts will be used, all service and

repairs must be performed by a HITACHI

AUTHORIZED SERVICE CENTER, ONLY.

7. Service parts list

CAUTION:

●

Repair, modification and inspection of Hitachi

Power Tools must be carried out by a Hitachi

Authorized Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools,

the safety regulations and standards prescribed

in each country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest

technological advancements.

Accordingly, some parts may be changed without

prior notice.

01Eng_G10SN_US 8/10/10, 13:3112

English

13

WARNING:

Never use any accessories other than those mentioned below.

The use of any accessories other than those mentionded below or attachments not intended for use such as

cup wheel, cut-off wheel or saw blade is dangerous and may cause personal injury or property damage.

NOTE:

Accessories are subject to change without any obligation on the part of the HITACHI.

STANDARD ACCESSORIES

(1) For grinder supplied with Carrying Case

䡬

Wrench .................................................................. 1

(Code No. 938332Z ............................... G12SN)

䡬

Side Handle (Code No. 318312) ........................... 1

䡬

Daimond wheel ..................................................... 1

4-1/2” (115 mm) external dia. × 5/64” (2 mm)

thickness × 7/8” (22.23 mm) hole dia.

(Code No. 994314 or 307006) .................... G12SN

(2) For grinder supplied without Carrying Case

䡬

Wrench .................................................................. 1

(Code No. 313933 ................................. G10SN)

(Code No. 938332Z ................. G12SN, G13SN)

䡬

Side Handle (Code No. 318312) ........................... 1

䡬

Depressed center wheel ....................................... 1

4” (100 mm) external dia. × 5/32” (4 mm) thickness

× 5/8” (16 mm) hole dia.

(Code No. 316820) ................................. G10SN

4-1/2" (115 mm) external dia. × 1/4” (6 mm)

thickness × 7/8” (22.23 mm) hole dia.

(Code No. 316821) ................................. G12SN

5" (125 mm) external dia. × 1/4” (6 mm)

thickness × 7/8” (22.23 mm) hole dia.

(Code No. 316822) ................................. G13SN

NOTE:

Specifications are subject to change without any

obligation on the part of the HITACHI.

ACCESSORIES

01Eng_G10SN_US 8/10/10, 13:3113

Page is loading ...

20

Français

CONSERVER CES INSTRUCTIONS

ET

LES METTRE A LA DISPOSITION DES AUTRES UTILISATEURS

ET

PROPRIETAIRES DE CET OUTIL!

02Fre_G10SN_US 8/10/10, 13:3220

Page is loading ...

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construc-

tion activities contains chemicals known to the State of California to cause cancer,

birth defects or other reproductive harm. Some examples of these chemicals are:

● Lead from lead-based paints,

● Crystalline silica from bricks and cement and other masonry products, and

● Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type

of work. To reduce your exposure to these chemicals: work in a well ventilated area,

and work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

AVERTISSEMENT:

La poussière résultant d'un ponçage, d'un sciage, d'un meulage, d'un perçage ou de toute

autre activité de construction renferme des produits chimiques qui sont connus par l'Etat

de Californie pour causer des cancers, des défauts de naissance et autres anomalies de

reproduction. Nous énumérons ci-dessus certains de ces produits chimiques:

● Plomb des peintres à base de plomb,

● Silice cristalline des briques et du ciment et autres matériaux de maçonnerie, et

● Arsenic et chrome du bois d'oeuvre traité chimiquement.

Le risque d'exposition à ces substances varie en fonction de la fréquence d'exécution

de ce genre de travail. Pour réduire l'exposition à ces produits chimiques, travailler

dans un lieu bien ventilé, et porter un équipement de protection agréé, par exemple

un masque anti-poussière spécialement conçu pour filter les particules microscopiques.

ADVERTENCIA:

Algunos polvos creados por el lijado mecánico, el aserrado, el esmerilado, el taladrado

y otras actividades de construcción contienen sustancias químicas conocidas por le

Estado de California como agentes cancerígenos, defectos congénitos y otros daños

reproductores. Algunos ejemplos de estas sustancias químicas son:

● El plomo de las pinturas a base de plomo,

● El sílice cristalino de los ladrillos y cemento y otros productos de mampostería, y

● El arsénico y el cromo de la madera tratada químicamente.

El riesgo resultante de la exposición varía según la frecuencia con que se realiza este

tipo de trabajo. Para reducir la exposicíon a esta sustancias químicas: trabaje en un lugar

bien ventilado y realice el trabajo utilizando el equipamiento apropiado, tal como las

máscaras para el polvo especialmente diseñados para eliminar las partículas minúsculas.

301

Code No. C99194162 F

Printed in China

Issued by

Hitachi Koki Co., Ltd.

Shinagawa Intercity Tower A, 15-1, Konan 2-chome,

Minato-ku, Tokyo 108-6020, Japan

Distributed by

Hitachi Koki U.S.A., Ltd.

3950 Steve Reynolds Blvd.

Norcross, GA 30093

Hitachi Koki Canada Corp.

450 Export Blvd. Unit B,

Mississauga ON L5S 2A4

Hitachi Power Tools de Mexico, S. A. de C. V.

Francisco Petrarca No. 239 Local A

Col. Chapultepec Morales C. P. 11570

Mexico, D. F.

04Back_G10SN_US 12/17/12, 12:28 PM44

Hitachi G 13SN Safety Instructions And Operation Manual

This manual is also suitable for

Hitachi G 13SN Safety Instructions And Operation Manual

in other languages

Related papers

Other documents