BDI Terrace 1153 User manual

Type
User manual
1
Product Registration
Registering your new BDI product allows us to send you important
product updates, service information and helpful hints related to
your BDI products. Register today, and you will be entered to win
free a BINK table from BDI: www.bdiusa.com/register
Placement and Maintenance
Your Terrace Console Table is designed for indoor use on level
floors. Clean wood veneer and steel parts with a moist cloth and
clean glass with glass cleaner.
Terrace is engineered for easy assembly. Carefully follow this
procedure to prevent any damage. Do not use power tools for
assembly of this product.
Step 1
Unpack and identify the parts listed below. The assembly
workspace should be a non-marring surface such as carpet.
For missing hardware pieces, contact BDI Customer Service at:
For all other concerns, please contact your BDI retailer.
Designed by Matthew Weatherly.
These distinctive product configurations are protected by US and international patents, trade dress, and/or
copyright laws. Terrace & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2016, BDI
Made in China. 11.16.2016 V1
T2 Hex Wrench x 1
A1 Wood Panel x 1
H1 1/4-20 x 19 mm
Machine Screw x 16
H2 1/4-20 x 10 mm
Machine Screw x 8
A2 Leg Assembly x 2
A3 Leg Brace x 1
C1 Glass Top x 1
bdiusa.com
customerservice@bdiusa.com
TERRACE
TM
1153
CONSOLE TABLE
bdiusa.com
customerservice@bdiusa.com
TERRACE 1153
CONSOLE TABLE
2
T2
Step 2 - Attach Leg Assemblies
With one hand, carefully position the wood panel A1 on edge. With other hand, slide 1 leg assembly into the
2 notches on the bottom of the wood panel aligning the attachment plates with the corresponding recessed
areas. Make sure the threaded holes on the leg assembly face inward. Loosely attach the leg assembly
with 8 screws H1 using hex wrench T2. Do not tighten the screws yet (otherwise the leg brace may not fit).
Attach the second leg assembly but do not fully tighten the screw until after the next step.
H1 x 8
H1 x 8
T2
T2
A1
T2
ATTENTION!
Threaded holes
face inward
Attachment plate
T2
T2
A1
H1 X 8
H1 X 8
ATTENTION!
Threaded holes
face inward
bdiusa.com
customerservice@bdiusa.com
TERRACE 1153
CONSOLE TABLE
3
Step 3 Attach Leg Brace
Place the leg brace A3 inbetween the 2 leg assemblies and align the holes with the threaded holes on the
leg assemblies. Attach the leg brace with 8 screws H2 using hex wrench T2. Fully tighten all screws H1
from the previous step.
Step 4 Adjust Levelers / Place the Glass Top
With help from another person, place your Terrace Console on its feet. Position your table and check to make
sure it is level. Your Terrace Console Table comes with adjustable levelers under each foot. If necessary, dial
out one or more of the levelers to stabilize the table. Place the glass top onto the top of the legs and align all 4
edges of the glass top with the wood panel.
2 Person Task
A3
H2
Adjustable
Levelers
H2 x 8
T2
  • Page 1 1
  • Page 2 2
  • Page 3 3

BDI Terrace 1153 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI