Gigabyte GA-8TRX330 User manual

GA-8TRX330(-L)

Intel

®

Pentium

®

4 Socket 478 Processor Motherboard

User's Manual

Rev. 1002

12ME-8TRX330L-1002

Motherboard

GA-8TRX330

Aug. 26, 2004

Motherboard

GA-8TRX330

Copyright

The trademarks mentioned in the manual are legally registered to their respective companies.

Notice

The written content provided with this product is the property of Gigabyte.

No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any

means without Gigabyte's prior written permission. Specifications and features are subject to

change without prior notice.

Product Manual Classification

In order to assist in the use of this product, Gigabyte has categorized the user manual in the

following:

n For quick installation, please refer to the "Hardware Installation Guide" included with the

product.

n For detailed product information and specifications, please carefully read the

"Product User Manual".

n For detailed information related to Gigabyte's unique features, please go to Gigabyte's

website under "Technology Guide" where information can be downloaded in .pdf format.

Fore more product details, please click onto Gigabyte's website at www.gigabyte.com.tw

- 4 -

Table of Contents

GA-8TRX330(-L ) Motherboard Layout ......................................................................6

Block Diagram ...........................................................................................................7

Chapter 1 Hardware Installation .................................................................................9

1-1 Considerations Prior to Installation ..................................................................... 9

1-2 Feature Summary ............................................................................................... 10

1-3 Installation of the CPU and Heatsink ................................................................ 12

1-3-1 Installation of the CPU ..................................................................................... 12

1-3-2 Installation of the Heatsink ............................................................................... 13

1-4 Installation of Memory ........................................................................................ 14

1-5 Installation of Expansion Cards ......................................................................... 16

1-6 I/O Back Panel Introduction ............................................................................... 17

1-7 Connectors Introduction ..................................................................................... 18

Chapter 2 BIOS Setup ........................................................................................... 29

The Main Menu (For example: BIOS Ver. : E19) ........................................................ 30

2-1 Standard CMOS Features .................................................................................. 32

2-2 Advanced BIOS Features .................................................................................. 34

2-3 Integrated Peripherals ........................................................................................ 35

2-4 Power Management Setup ................................................................................. 38

2-5 PnP/PCI Configurations ..................................................................................... 40

2-6 PC Health Status ................................................................................................. 41

2-7 Frequency/Voltage Control ................................................................................ 42

2-8 Top Performance ................................................................................................. 43

2-9 Load Fail-Safe Defaults ...................................................................................... 44

2-10 Load Optimized Defaults .................................................................................... 44

2-11 Set Supervisor/User Password ......................................................................... 45

2-12 Save & Exit Setup ............................................................................................... 46

2-13 Exit Without Saving ............................................................................................. 46

- 5 -

Chapter 3 Install Drivers ......................................................................................... 49

3-1 Install Chipset Drivers ........................................................................................ 49

3-2 Software Applications ......................................................................................... 50

3-3 Driver CD Information ......................................................................................... 50

3-4 Hardware Information ......................................................................................... 51

3-5 Contact Us ........................................................................................................... 51

Chapter 4 Appendix ............................................................................................... 53

4-1 Unique Software Utilities .................................................................................... 53

4-1-1 Xpress Recovery Introduction ..........................................................................53

4-1-2 Flash BIOS Method Introduction ......................................................................56

4-1-3 2 / 4 / 6 Channel Audio Function Introduction .................................................. 65

4-2 Troubleshooting................................................................................................... 71

- 6 -

GA-8TRX330(-L ) Motherboard Layout

KB_MS

ATX_12V

CPU_FAN

Socket 478

ATX

IR

BAT

BIOS

PCI4

PCI5

S_ATA2

PWR_LED

F_PANEL

COMB

SPDIF_IO

PCI3

F_U SB2

F_U SB1

IT8712

COMA

LPT

USB

LAN

(

*

)

RTL

8100C

(

*

)

F_AU DIO

ATi RX330

AUDIO

S_ATA1

ATi SB300

(IXP 300)

DDR1

DDR2

DDR3

DDR4

IDE1

SYS_FAN

FDD

AGP

PCI1

PCI2

CODEC

R_U SB

GA-8TRX330

CD_IN

CLR_CMOS

IDE2

MOSHSINK

LED1

2X_DET

(

*

)

(

*

)

Only for GA-8TRX330-L.

- 7 -

Block Diagram

Pentium 4

Socket 478

CPU

ATi RX330

AC97

CODEC

ATi SB300

(IXP 300)

CPUCLK+/- (100/133/200 MHz)

System Bus

400/533/800 MHz

200/266/333/400 MHz

ZCLK (66MHz)

HCLK+/- (100/133/200 MHz)

66 MHz

33 MHz

14.318 MHz

48 MHz

24 MHz

33 MHz

LPC BUS

AGP 4X/8X

AGPCLK

(66MHz)

5 PCI

PCICLK

(33MHz)

AC97 Link

MIC

LINE-IN

LINE-OUT

8 USB

Ports

ATA33/66/100/133

IDE Channels

Floppy

LPT Port

PS/2

KB/Mouse

COM

Ports

BIOS

IT8712

RTL8100C

(

*

)

RJ45

(

*

)

DDR

(

*

)

Only for GA-8TRX330-L.

- 8 -

Hardware Installation- 9 -

English

1-1 Considerations Prior to Installation

Preparing Your Computer

The motherboard contains numerous delicate electronic circuits and components which can

become damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please

follow the instructions below:

1. Please turn off the computer and unplug its power cord.

2. When handling the motherboard, avoid touching any metal leads or connectors.

3. It is best to wear an electrostatic discharge (ESD) cuff when handling electronic components

(CPU, RAM).

4. Prior to installing the electronic components, please have these items on top of an antistatic pad or

within a electrostatic shielding container.

5. Please verify that you the power supply is switched off before unplugging the power supply connector

from the motherboard.

Installation Notices

1. Prior to installation, please do not remove the stickers on the motherboard. These stickers are required

for warranty validation.

2. Prior to the installation of the motherboard or any hardware, please first carefully read the information

in the provided manual.

3. Before using the product, please verify that all cables and power connectors are connected.

4. To prevent damage to the motherboard, please do not allow screws to come in contact with the

motherboard circuit or its components.

5. Please make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

6. Please do not place the computer system on an uneven surface.

7. Turning on the computer power during the installation process can lead to damage to system

components as well as physical harm to the user.

8. If you are uncertain about any installation steps or have a problem related to the use of the product,

please consult a certified computer technician.

Instances of Non-Warranty

1. Damage due to natural disaster, accident or human cause.

2. Damage as a result of violating the conditions recommended in the user manual.

3. Damage due to improper installation.

4. Damage due to use of uncertified components.

5. Damage due to use exceeding the permitted parameters.

6. Product determined to be an unofficial Gigabyte product.

Chapter 1 Hardware Installation

GA-8TRX330(-L) Motherboard - 10 -

English

CPU w Supports the latest Intel

®

Pentium

®

4 Socket 478 CPU

w Supports 800/533/400MHz FSB

w L2 cache varies with CPU

Chipset w North Bridge: ATi RX330

w South Bridge: ATi SB300(IXP 300)

Memory w 4 DDR DIMM memory slots (supports up to 4GB memory)

(Note 1)

w Supports 2.5V DDR DIMM

w Supports dual channel DDR 400/333/266/200 DIMM

(Note 2)

Slots w 5 PCI slots

w 1 AGP slot

IDE Connections w 2 IDE connection (UDMA 33/ATA 66/ATA 100/ATA 133), allows connection of 4

IDE devices

FDD Connections w 1 FDD connection, allows connection of 2 FDD devices

Onboard SATA w 2 Serial ATA connections

Peripherals w 1 parallel port supporting Normal/EPP/ECP mode

w 1 Serial port (COMA), onboard COMB connection

w 8 USB 2.0/1.1 ports (rear x 4, front x 4 via cable)

w 1 front audio connector

w 1 IR connector

w 1 PS/2 keyboard port

w 1 PS/2 mouse port

Onboard LAN

(

*

)

w Onboard RTL8100C Chipset (10/100 Mbit)

w 1 RJ 45 port

Onboard Audio w Realtek ALC655 CODEC

w Support Jack-Sensing

w Supports 2 / 4 / 6 channel audio

w Line Out / 2 front speaker

w Line In / 2 rear speaker(by s/w switch)

w Mic In / center& subwoofer(by s/w switch)

w Supports SPDIF In/Out connection

w CD In

1-2 Feature Summary

(

*

)

Only for GA-8TRX330-L.

(Note 2) Due to chipset limitation, the total number of memory chips of memory module(s) installed in the

same channel cannot be more than eight, otherwise DDR400 memory will slow down to DDR333.

For the latest information about memory modules supported on this motherboard, please go to

GIGABYTE's website.

(Note 1) Due to standard PC architecture, a certain amount of memory is reserved for system usage and

therefore the actual memory size is less than the stated amount.

For example, 4 GB of memory size will instead be shown as 3.xxGB memory during system startup.

Hardware Installation- 11 -

English

I/O Control w IT8712

Hardware Monitor w System voltage detection

w CPU temperature detection

w CPU / System fan speed detection

w CPU warning temperature

w CPU / System fan failure warning

BIOS w Use of licensed AWARD BIOS

w Supports Q-Flash

Additional Features w Supports @BIOS

w Supports EasyTune

Overclocking w Over Clock via BIOS (CPU)

Form Factor w ATX form factor; 30.5cm x 24.4cm

GA-8TRX330(-L) Motherboard - 12 -

English

1-3 Installation of the CPU and Heatsink

Before installing the CPU, please comply with the following conditions:

1. Please make sure that the motherboard supports the CPU.

2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong

direction, the CPU will not insert properly. If this occurs, please change the insert direction

of the CPU.

3. Please add an even layer of heat sink paste between the CPU and heatsink.

4. Please make sure the heatsink is installed on the CPU prior to system use, otherwise

overheating and permanent damage of the CPU may occur.

5. Please set the CPU host frequency in accordance with the processor specifications. It is not

recommended that the system bus frequency be set beyond hardware specifications since it

does not meet the required standards for the peripherals. If you wish to set the frequency

beyond the proper specifications, please do so according to your hardware specifications

including the CPU, graphics card, memory, hard drive, etc.

HT functionality requirement content :

Enabling the functionality of Hyper-Threading Technology for your computer system requires all

of the following platform components:

- CPU: An Intel

®

Pentium 4 Processor with HT Technology

- Chipset: An ATi Chipset that supports HT Technology

- BIOS: A BIOS that supports HT Technology and has it enabled

- OS: An operation system that has optimizations for HT Technology

1-3-1 Installation of the CPU

Pin1 indicator

Fig. 2

Pull the rod to the

90-degree directly.

Angling the

rod to 65

0

Fig. 1

Angling the rod to 65-

degree maybe feel a

kind of tight , and then

continue pull the rod to

90-d egree wh en a

"click" noise is heard.

Socket

Actuation

Lever

Fig. 3

CPU Top View

Pin1 indicator

Fig. 4

Locate Pin 1 in the

socket and look

for a (golden) cut edge

on the CPU

upper corner. Then

insert the CPU

into the socket.

Hardware Installation- 13 -

English

1-3-2 Installation of the Heatsink

1. Please use Intel approved cooling fan.

2. We recommend you to apply the thermal tape to provide better heat conduction

between your CPU and cooling fan.

(The CPU cooling fan might stick to the CPU due to the hardening of the

thermal paste. During this condition if you try to rem ove the cooling fan, you

might pull the processor out of the CPU socket alone with the cooling fan, and

might damage the processor. To avoid this from happening, we suggest you to

either use thermal tape instead of therm al paste, or rem ove the cooling fan with

extreme caution.)

3. Make sure the CPU fan power cable is plugged in to the CPU fan connector, this

completes the installation. Please refer to CPU cooling fan user's manual for

more detail installation procedure.

Fig. 2

Make sure the CPU fan

is plugged to the CPU

fan connector, than

install complete.

Fig.1

Fasten the cooling fan

supporting-base onto

the CPU socket on the

motherboard.

Before installing the CPU cool fan , adhere to the following warning:

GA-8TRX330(-L) Motherboard - 14 -

English

Fig.1

The DIMM socket has a notch, so the DIMM memory module

can only fit in one direction. Insert the DIM M memory module

vertically into the DIMM socket. Then push it down.

Fig.2

Close the plastic clip at both edges of the DIMM sockets to

lock the DIMM module.

Reverse the installation steps when you wish to remove the

DIMM module.

The motherboard supports DDR memory modules, whereby BIOS will automatically detect memory

capacity and specifications. Memory modules are designed so that they can be inserted only in one direction.

The memory capacity used can differ with each slot.

Before installing the memory modules, please comply with the following conditions:

1 . Please make sure that the memory used is supported by the motherboard. It is recommended that

memory of similar capacity, specifications and brand be used.

2 . Before installing or removing memory modules, please make sure that the computer power is switched

off to prevent hardware damage.

3 . Memory modules have a foolproof insertion design. A memory module can be installed in only one

direction. If you are unable to insert the module, please switch the direction.

1-4 Installation of Memory

Notch

DDR

Hardware Installation- 15 -

English

Dual Channel DDR

GA-8TRX330(-L) supports the Dual Channel Technology. After operating the Dual Channel Technology, the

bandwidth of Memory Bus will add double.

GA-8TRX330(-L) includes 4 DIMM sockets, and each Channel has two DIMM sockets as following:

Channel A : DDR 1, DDR 2

Channel B : DDR 3, DDR 4

If you want to operate the Dual Channel Technology, please note the following explanations due

to the lim itation of Intel chipset specifications.

1. One/three DDR memory module is installed: The Dual Channel Technology can't operate

when only one DDR memory module is installed.

2. Two DDR memory modules are installed (the same memory size and type): The Dual

Channel Technology will operate when two memory modules are inserted individually into

Channel A and B. If you install two memory modules in the same channel, the Dual Channel

Technology will not operate.

3. Four DDR memory modules are installed: If you install four memory modules at the same

time, the Dual Channel Technology will operate only when those modules have the same

memory size and type.

We'll strongly recommend our user to slot two DDR memory modules into the DIMMs with the same color in

order for Dual Channel Technology to work.

The following table is for Dual Channel Technology combination: (DS: Double Side, SS: Single Side)

2 memory modules

4 memory modules

DDR 1 DDR 2 DDR 3 DDR 4

DS/SS X DS/SS X

X DS/SS X DS/SS

DS/SS DS/SS DS/SS DS/SS

GA-8TRX330(-L) Motherboard - 16 -

English

1-5 Installation of Expansion Cards

You can install your expansion card by following the steps outlined below:

1. Read the related expansion card's instruction document before install the expansion card into the

computer.

2. Remove your computer's chassis cover, screws and slot bracket from the computer.

3. Press the expansion card firmly into expansion slot in motherboard.

4. Be sure the metal contacts on the card are indeed seated in the slot.

5. Replace the screw to secure the slot bracket of the expansion card.

6. Replace your computer's chassis cover.

7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.

8. Install related driver from the operating system.

Installing a AGP expansion card:

AGP Card

Please carefully pull out the small white- drawable

bar at the end of the AGP slot when you try to install/

Uninstall the AGP card. Please align the AGP card to

the onboard AGP slot and press firmly down on the

slot .Make sure your AGP card is locked by the small

white- drawable bar.

When an AGP 2x (3.3V) card is installed the 2X_DET will light up, indicating a non-supported

graphics card is inserted. Informing users that system might not boot up normally due to AGP 2x

(3.3V) is not supported by the chipset.

Hardware Installation- 17 -

English

PS/2 Keyboard and PS/2 Mouse Connector

To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the

lower port (purple).

Parallel Port

The parallel port allows connection of a printer, scanner and other peripheral devices.

COM A (Serial Port)

Connects to serial-based mouse or data processing devices.

USB port

Before you connect your device(s) into USB connector(s), please make sure your device(s) such as

USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface. Also make sure

your OS supports USB controller. If your OS does not support USB controller, please contact OS ven

dor for possible patch or driver upgrade. For more information please contact your OS or device(s)

vendors.

LAN Port

(

*

)

The provided Internet connection is fast Ethernet, providing data transfer speeds of 10/100Mbps.

Line In

Devices like CD-ROM, walkman etc. can be connected to Line In jack.

Line Out

Connect the stereo speakers, earphone or front surround channels to this connector.

MIC In

Microphone can be connected to MIC In jack.

1-6 I/O Back Panel Introduction

You can use audio software to configure 2-/4-/6-channel audio functioning.

(

*

)

Only for GA-8TRX330-L.

(

*

)

GA-8TRX330(-L) Motherboard - 18 -

English

1-7 Connectors Introduction

1) ATX_12V

2) ATX (Power Connector)

3) CPU_FAN

4) SYS_FAN

5) FDD

6) IDE1/IDE2

7) S_ATA1 / S_ATA2

8) LED1

9) 2X_DET

10) PWR_LED

11) F_PANEL

12) F_AUDIO

13) CD_IN

14) SPDIF_IO

15) COMB

16) F_USB1 / F_USB2

17) IR

18) CLR_CMOS

19) BAT

1 3

4

8

17

19

7

14

1015

16

11

18

9

2

5

12

4

13

6

Hardware Installation- 19 -

English

1/2) ATX_12V/ATX (Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the

components on the motherboard. Before connecting the power connector, please make sure that all

components and devices are properly installed. Align the power connector with its proper location on

the motherboard and connect tightly.

The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power

connector is not connected, the system will not start.

Caution!

Please use a power supply that is able to handle the system voltage requirements. It is

recommended that a power supply that can withstand high power consumption be used (300W or

greater). If a power supply is used that does not provide the required power, the result can lead to an

unstable system or a system that is unable to start.

Pin No. Definition

1 GND

2 GND

3 +12V

4 +12V

2 0

1 0

11

1

Pin No. Definition

1 3.3V

2 3.3V

3 GND

4 VCC

5 GND

6 VCC

7 GND

8 Power Good

9 5V SB(stand by +5V)

10 +12V

11 3.3V

12 -12V

13 GND

14 PS_ON(softOn/Off)

15 GND

16 GND

17 GND

18 -5V

19 VCC

20 VCC

2

3

4

1

GA-8TRX330(-L) Motherboard - 20 -

English

3/4) CPU_FAN / SYS_FAN (Cooler Fan Power Connector)

The cooler fan power connector supplies a +12V power voltage via a 3-pin power connector and

possesses a foolproof connection design.

Most coolers are designed with color-coded power connector wires. A red power connector wire

indicates a positive connection and requires a +12V power voltage. The black connector wire is

the ground wire (GND).

Please remem ber to connect the power to the cooler to prevent system overheating and failure.

Caution!

Please remember to connect the power to the CPU fan to prevent CPU overheating and failure.

1

CPU_FAN

SYS_FAN

5) FDD (Floppy Connector)

The FDD connector is used to connect the FDD cable while the other end of the cable connects to the

FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB.

Please connect the red power connector wire to the pin1 position.

1

2

3 3

3 4

Pin No. Definition

1 GND

2 +12V

3 Sense

Page is loading ...

Gigabyte GA-8TRX330 User manual

This manual is also suitable for

Gigabyte GA-8TRX330 User manual

Related papers

Other documents