Marantec EM 110 Owner's manual

Brand: Marantec

Model: EM 110

Type: Owner's manual

Marantec EM 110 is an expansion module that enhances the functionality of the Control x.plus control unit. It offers additional features such as signal light control, potential-free radio contact, and extended levels of programming options. With this module, you can customize the operation of your door system to suit your specific needs, improving convenience and security.

Expansion module EM 110

Manual for installation and operation

2 Manual for installation and operation, Expansion module EM 110 GB (#85967)

2. Table of contents

Caution!

Danger of personal injury!

The following safety advice must be

observed at all times so as to avoid

personal injury!

Attention!

Danger of material damage!

The following safety advice must be

observed at all times so as to avoid

material damage!

Advice / Tip

Check

Reference

Advice

1. Meaning of symbols . . . . . . . . . .2

2. Table of contents . . . . . . . . . . . .2

3. General safety advice . . . . . . . . .3

4. Product overview . . . . . . . . . . . .5

4.1 Supply package . . . . . . . . . . . .5

4.2 Dimensions . . . . . . . . . . . . . . .5

5. Installation . . . . . . . . . . . . . . . . .6

5.1 Install expansion module . . . . .6

5.2 Wiring of the expansion

module . . . . . . . . . . . . . . . . . .6

6. Programming . . . . . . . . . . . . . .10

6.1 Functions of the module . . . .10

6.2 Extended levels of the

Control x.plus control unit . .14

7. Attachment . . . . . . . . . . . . . . . .15

EC Declaration of Conformity . . . . . . .15

1. Meaning of symbols

Manual for installation and operation, Expansion module EM 110 GB (#85967) 3

3. General safety advice

Target group

This product may only be installed, connected and put into operation by qualified and trained professionals!

Qualified and trained specialist personnel are persons

- who have knowledge of the general and special safety regulations,

- who have knowledge of the relevant electro-technical regulations,

- with training in the use and maintenance of suitable safety equipment,

- who are sufficiently trained and supervised by qualified electricians,

- who are able to recognise the particular hazards involved when working with electricity,

- with knowledge regarding applications of the EN 12635 standard (installation and usage requirements).

Warranty

For an operations and safety warranty, the advice in this instruction manual has to be observed.

Disregarding these warnings may lead to personal injury or material damage. If this advice is disregarded,

the manufacturer will not be liable for damages that might occur.

To avoid installation errors and damage to the device, it is imperative that the installation instructions are

followed. The product may only be operated after reading these installation and operating instructions.

The installation and operating instructions are to be given to the door system user, who must keep them

safe. They contain important advice for operation, checks and maintenance.

This item is produced according to the directives and standards mentioned in the Manufacturer's

Declaration and in the Declaration of Conformity. The product has left the factory in perfect condition with

regard to safety.

Power-operated windows, doors and gates must be checked by an expert (and this must be documented)

before they are put into operation and thereafter as required, but at least once a year.

Correct use

The expansion module expands the Control x.plus control unit.

Beside the advice in these instructions, please observe the general safety and accident

prevention regulations!

Our sales and supply terms and conditions are effective.

Please read carefully!

3. General safety advice

Installation tips

• Ensure that the devices to be connected (doors etc.) are in a mechanically faultless state.

• Before commencing cabling works it is very important to disconnect the system from the electricity supply.

Ensure that the electricity supply remains disconnected throughout the cabling works.

• Adhere to the local protection regulations.

• Lay the electricity supply cables and control cables; these MUST be laid separately.

The operating voltage is 24 V.

Information on cleaning the operator system

Never use water jets, high pressure cleaners, acids or bases for cleaning.

Please read carefully!

4 Manual for installation and operation, Expansion module EM 110 GB (#85967)

4.1 Supply package 4.2 Dimensions

1 Expansion module

2 Cable harness for module connection

4. Product overview

Manual for installation and operation, Expansion module EM 110 GB (#85967) 5

4.1 / 1

4.2 / 1

126

6 Manual for installation and operation, Expansion module EM 110 GB (#85967)

Designation

Type / function

A Operating indicator

B Display for output XH19B

C Display for output XH19A

Display for control element

activated

XB59 Control element connections

XB41A

Connection of Control x.plus

control unit

XB41B Connection of further module

XH19A Connection of signalling device

XH19B Connection of signalling device

5.1 Install expansion module 5.2 Wiring of the expansion

module

5. Installation

• Fit the expansion module (B) in the type 4 /

type 5 (A) expansion housing type.

5.2.1 Overview of the module connections

5.1 / 1

5.2.1 / 1

XB59

XB41A

XH19A

XH19B

XB41B

Manual for installation and operation, Expansion module EM 110 GB (#85967) 7

5. Installation

5.2.2 Connection of the modules

XB41A

• Connect the Control x.plus control unit to the

connecting socket XB41A.

• Connect further modules to socket XB41B as

required.

5.2.2 / 1

XB41B

Connection of the control unit and a further

module

8 Manual for installation and operation, Expansion module EM 110 GB (#85967)

5. Installation

Advice:

To activate the module, a single com-

mand must be given via the connec-

tion XB59 (impulse to B5-8). As a

result further menus in the Control

x.plus control unit will be activated.

Reference:

The activated menus are described in

section 6.2.

-XB59

-SB8

13 14

-SB4

13 14

-SB47

13 14

-SB6

13 14

B5 8 4 47 6

5.2.2 / 2

Designation

Type / function

SB8 Operating button for IMPULSE*

SB4

Operating button

intermediate CLOSE position*

SB47 Has no function

SB6 Operating button for OPEN**

Connection of control element (XB59)

M08E002

* The function sequence is programmable in

level 8 / menu 6 of the Control x.plus control

unit.

** The function “active without stop” is not

modifiable through level 8 / menu 5.

-XH19A

-HH94

H1 92 94

Manual for installation and operation, Expansion module EM 110 GB (#85967) 9

Connection for signal light (XH19B)

Connection for signal light (XH19A)

-XH19B

-HH94

H1 92 94

5.2.2 / 4

M08E002

Designation

Type / function

HH94 Signal light supplied by customer

XH19A Connection of signalling device

Designation

Type / function

HH94 Signal light supplied by customer

XH19B Connection of signalling device

5.2.2 / 3

M08E002

5. Installation

Attention!

To avoid damage being caused to the

circuit board, the contact loading

(max. 230 V / 0.5 A) must be

observed.

6. Programming

10 Manual for installation and operation, Expansion module EM 110 GB (#85967)

6.1 Functions of the module

6.1.1 Functions of the module

* Identification plate

** Terminal block

Example 1

XH19A**

XH19B**

Control EM 110 Typ A 1 0 / G 2 0*

Door not in intermediate OPEN position: signalling device OFF

Door in intermediate OPEN position: signalling device illuminated

Function: door in intermediate OPEN position

If door stationary: signalling device OFF

If door is moving: signalling device flashes

Function: door in motion

Example 2

XH19A**

XH19B**

Control EM 110 Typ E 2 0 / J X X*

No further adjustment possible

Function: signal light (level 3 / menu 7)

Door not in OPEN position: signalling device OFF

Door in OPEN position: signalling device illuminated

Function: door in OPEN position

Manual for installation and operation, Expansion module EM 110 GB (#85967) 11

6. Programming

* Identification plate

** Terminal block

Example 3

XH19A**

XH19B**

Control EM 110 Typ L 1 X / K X X*

No further adjustment possible

Function: lighting (level 5 / menu 4)

No further adjustment possible

1: ON/OFF

Function: potential-free contact (level 4 / menu 8)

6. Programming

12 Manual for installation and operation, Expansion module EM 110 GB (#85967)

Function

Programming in the

Control x.plus control

unit

Adjustment of functions

A Door in motion - Refer to section 6.1.3

B Door moves to OPEN - Refer to section 6.1.3

C Door moves to CLOSED - Refer to section 6.1.3

D Door in any intermediate position - Refer to section 6.1.3

E Door in intermediate OPEN position - Refer to section 6.1.3

F Door in CLOSED door position - Refer to section 6.1.3

G Door in intermediate OPEN position - Refer to section 6.1.3

H Door in intermediate CLOSED position - Refer to section 6.1.3

I Motor starts - Wiping impulse

J Signal light Level 3, menu 7 -

Lighting (door in motion +

lighting duration)

Level 5, menu 4 -

L Potential-free radio contact Level 4, menu 8

0 Wiping impulse

1 ON / OFF

M Problem - Refer to section 6.1.3

N Maintenance indicator - Refer to section 6.1.3

6.1.2 Function table

Manual for installation and operation, Expansion module EM 110 GB (#85967) 13

6. Programming

6.1.3 Table of values

Function fulfilled Function not fulfilled

0 OFF 1 flashing

0 OFF 2 illuminated

1 flashing 0 OFF

1 flashing 2 illuminated

2 illuminated 0 OFF

2 illuminated 1 flashing

No further

adjustment

possible

No further

adjustment

possible

14 Manual for installation and operation, Expansion module EM 110 GB (#85967)

6. Programming

Level 4 – Remote programming

Menü 8: Potential-free contact

LED 7 flashes slowly -> press the hand transmitter button -> LED 7 flashes quickly

Level 5 – Special function

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Menu 4: Lighting duration (in seconds)

OFF 5 10 15 20 25 30 35 40 50 80 100 120 150 180 255

Advice:

Potential-free contact by radio is only available if the module has the identification code LOX

or L1X on the corresponding connection.

Advice:

The lighting duration is only available if the module has the identification code KXX on the

corresponding connection.

6.2 Extended levels of the Control x.plus control unit

An activated module results in the menus which follow in the Control x.plus control unit being activated.

Manual for installation and operation, Expansion module EM 110 GB (#85967) 15

EC Declaration of Conformity

We hereby declare that the product sold by us

and mentioned below corresponds in its design,

construction and version to the relevant and basic

health and safety requirements of the following

EC regulations: EMC Directive, Machinery Directive

and Low Voltage Directive.

Product changes made without our consent will

render this Declaration void.

Product:

Relevant EC Regulations:

- EC EMC Directive

(89/336/EEC),

- Machinery Directive

(98/37/EEC) and

- Low Voltage Directive

(73/23/EEC and 93/68/EEC).

Applied harmonised standards, in particular:

EN 292-1 / EN 61000-6-2 / EN 61000-6-3 /

EN 55014 / EN 61000-3-2 / EN 61000-3-3 /

EN 60335-1 / EN 60335-2-95 / EN 12445 /

EN 12453 / EN 300220-1 / EN 301489-3 /

ETS 300683

Date / Signature

7. Attachment

English Copyright.

No part of this manual may be reproduced without our prior consent.

Subject to changes which are in the interest of technical improvements.

Version: 05.2008

#85 967

1 - GB/KD 36-0286 - M - 0.5 - 0508

85967

Marantec EM 110 Owner's manual

Marantec EM 110 Owner's manual

Marantec EM 110 Owner's manual

Related papers

Other documents