Page is loading ...
Revision :1.0
1
Revision Description Date
1.0 Release 2009/11/25
AR-ES5495
Installation Guide
Revision :1.0
2
Contents
1
Introduction to AR-ES5495………………………………………………….……… 3
1.1 Specifications…………………………………………………………………… 3
1.2 Packing List……………………………………………………………………… 3
1.3 System Dissection………………………………………………………………. 4
1.3-1 Dimensions………………………………………………………………… 4
1.3-2 Front Panel………………………………………………………………… 4
1.3-3 I/O Bracket………………………………………………………………… 5
1.4 System Configuration
……………………………………………………………………… 5
2
Procedure of Assembly/Disassembly……………………………………………… 6
2.1 Installation 3.5“ HDD…………………………………………………………… 6
2.2 Installation Memory Module……………………………………………………. 10
2.3 Installation IDE-DOM…………………………………………………………… 12
Revision :1.0
3
1 Introduction to AR-ES5495
AR-ES5495 is an Intel Atom N270 + 945GSE chipset based platform; it provides fanless,
low power consumption, tiny size, easy installation and light weight for you. It is design for
low cost communication device; user can use it to build up simply internal communication
environment.
1.1 Specifications
Item Description
System AR-ES5495
CPU Board AR-B5495
System Dimensions 230×215×65 (mm)
1.2 Packing List
Description Q’ty
AR-ES5495 1
1GB DDRII 667MHz SDRAM (pre-installed) 1
Utility CD 1
AR-ES5495 system manual 1
LPT Cable 1
SATA Cable 2
SATA Power convert cable 1
44 pin IDE Cable 1
COM Port Cable w/bracket 1
Revision :1.0
4
1.3 System Dissection
1.3-1 Dimensions
230mm
65mm
1.3-2 Front Panel
Power Button
Reset Botton
HDD Led(red)
Power Led(green)
2 x USB
Revision :1.0
5
1.3-3 I/O Bracket
Serial Port
(COM1)
Micro
p
hone
LAN Port x 2
Power Inlet
Line-out
USB Port x 4
Serial Port
(COM2)
V
GA1 Port
Parallel Port
PS2 Keyboard
PS2 Mouse
1.4 System Configuration
Power Supply
AR-ES5495 Case IDE DOM
HDD Bracket
RAM
AR-B5495 Board
Revision :1.0
6
2 Procedure of Assembly/Disassembly
2.1 HDD Installation
The following instructions guide you to install 3.5” HDD
1. Unscrew two screws to unfasten the top cover.
Unscrew Unscrew
2. Take off the top cover.
1
2
Revision :1.0
7
3. Unscrew screws of the HDD-Bracket and take off the HDD-Bracket.
4. Put the 3.5” HDD on the HDD-Bracket and fix it by four screws.
Revision :1.0
8
5. Plug in the SATA cable and SATA power cable to the 3.5”HDD.
6. Then connect the SATA cable and SATA power cable to the AR-B5495 board.
SATA power cable
SATA cable
Revision :1.0
9
7. Put the HDD-Bracket back to chassis and fix it.
Screw
Screw
8. Fixed the top cover with the chassis.
Screw
Screw
Revision :1.0
10
2.2 Installation Memory Module
1. Please follow the steps above to remove the top cover.
2. Open the two latch of memory slot.
Latch
RAM module
2. Align the memory cutout with the memory module slot notch.
Cut out
Notch
Revision :1.0
11
3. Slide the memory into the memory module.
Check that the latches are closed, and
memory module is firmly installed.
PUSH
Revision :1.0
12
2.3 Installation IDE-DOM
1. The IDE-DOM slot please look at below photo.
2. Install IDE-DOM on below position.
IDE-DOM slot
First pin
/
