Supermicro A2SDV-16C-TLN5F User manual

Category
Server/workstation motherboards
Type
User manual

This manual is also suitable for

USER MANUAL
Revision 1.0
A2SDV-8C-TLN5F
A2SDV-12C+-TLN5F
A2SDV-16C-TLN5F
The information in this user’s manual has been carefully reviewed and is believed to be accurate. The vendor assumes
no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update
or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note:
For the most up-to-date version of this manual, please see our website at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described in this manual
at any time and without notice. This product, including software and documentation, is the property of Supermicro and/
or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except
as expressly permitted by the terms of said license.
IN NO EVENT WILL Super Micro Computer, Inc. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT
OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER
MICRO COMPUTER, INC. SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED
OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the
State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution
of any such disputes. Supermicro's total liability for all claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual,
may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only
to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate”.
WARNING: Handling of lead solder materials used in this product may expose you to lead, a
chemical known to the State of California to cause birth defects and other reproductive harm.
The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment,
nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical
systems whose failure to perform be reasonably expected to result in signicant injury or loss of life or catastrophic
property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products
for use in such ultra-hazardous applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully
indemnify, defend and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and
proceedings of any kind arising out of or related to such ultra-hazardous use or sale.
Manual Revision: 1.0
Release Date: February 14, 2018
Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy any part of this
document. Information in this document is subject to change without notice. Other products and companies referred
to herein are trademarks or registered trademarks of their respective companies or mark holders.
Copyright © 2018 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
3
Note: Additional Information given to differentiate various models or to provide in-
formation for correct system setup.
Preface
Preface
About This Manual
This manual is written for system integrators, IT technicians and knowledgeable end users.
It provides information for the installation and use of the A2SDV-8C/-12C+/-16C-TLN5F
motherboard.
About This Motherboard
The Supermicro A2SDV-8C/-12C+/-16C-TLN5F motherboard comes with an integrated Intel®
Atom SoC (FCBGA1310) supporting up to 16 Cores, a TDP of 32W and is optimized for
low-power consumption. This is a small form factor motherboard that is optimized for the
embedded solution. The following are some features that are offered: two M.2 connectors (one
M-Key and one B-Key), four 10G LAN ports, PCI-E 3.0 x8 expandability either via expansion
slot#6 OR #7, and the reliability and dependability of a Supermicro product. Please note that
this motherboard is intended to be installed and serviced by professional technicians only.
For processor/memory updates, please refer to our website at http://www.supermicro.com/
products/.
Conventions Used in the Manual
Special attention should be given to the following symbols for proper installation and to prevent
damage done to the components or injury to yourself:
Warning! Indicates high voltage may be encountered when performing a procedure.
Warning! Indicates important information given to prevent equipment/property damage
or personal injury.
Important: Important information given to ensure proper system installation or to
relay safety precautions.
4
Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: +1 (408) 503-8000
Fax: +1 (408) 503-8008
Email: [email protected] (General Information)
[email protected] (Technical Support)
Website: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: +31 (0) 73-6400390
Fax: +31 (0) 73-6416525
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Website: www.supermicro.nl
Asia-Pacic
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel: +886-(2) 8226-3990
Fax: +886-(2) 8226-3992
Website: www.supermicro.com.tw
A2SDV-8C/-12C+/-16C-TLN5F User's Manual
5
Table of Contents
Chapter 1 Introduction
1.1 Checklist ...............................................................................................................................8
Quick Reference ...............................................................................................................11
Quick Reference Table ......................................................................................................12
Motherboard Features .......................................................................................................14
1.2 Processor Overview ...........................................................................................................17
1.3 Special Features ................................................................................................................17
Recovery from AC Power Loss .........................................................................................17
1.4 System Health Monitoring ..................................................................................................17
Onboard Voltage Monitors ................................................................................................18
Fan Status Monitor with Firmware Control .......................................................................18
Environmental Temperature Control .................................................................................18
System Resource Alert......................................................................................................18
1.5 ACPI Features ....................................................................................................................18
1.6 Power Supply .....................................................................................................................19
1.7 Serial Port ...........................................................................................................................19
Chapter 2 Installation
2.1 Static-Sensitive Devices .....................................................................................................20
Precautions .......................................................................................................................20
Unpacking .........................................................................................................................20
2.2 Motherboard Installation .....................................................................................................21
Tools Needed ....................................................................................................................21
Location of Mounting Holes ..............................................................................................21
Installing the Motherboard.................................................................................................22
2.3 Memory Support and Installation .......................................................................................23
Memory Support ................................................................................................................23
DIMM Module Population Conguration ...........................................................................23
DIMM Module Population Sequence ................................................................................24
DIMM Installation ..............................................................................................................25
DIMM Removal .................................................................................................................25
2.4 Rear I/O Ports ....................................................................................................................26
Preface
6
2.5 Front Control Panel ............................................................................................................31
2.6 Connectors .........................................................................................................................36
Power Connections ...........................................................................................................36
Headers .............................................................................................................................38
2.7 Jumper Settings .................................................................................................................45
How Jumpers Work ...........................................................................................................45
2.8 LED Indicators ....................................................................................................................51
Chapter 3 Troubleshooting
3.1 Troubleshooting Procedures ..............................................................................................53
Before Power On ..............................................................................................................53
No Power ..........................................................................................................................53
No Video ...........................................................................................................................53
System Boot Failure ..........................................................................................................54
Memory Errors ..................................................................................................................54
Losing the System's Setup Conguration .........................................................................55
When the System Becomes Unstable ..............................................................................55
3.2 Technical Support Procedures ...........................................................................................57
3.3 Frequently Asked Questions ..............................................................................................58
3.4 Battery Removal and Installation .......................................................................................59
Battery Removal ................................................................................................................59
Proper Battery Disposal ....................................................................................................59
Battery Installation .............................................................................................................59
3.5 Returning Merchandise for Service ....................................................................................60
Chapter 4 BIOS
4.1 Introduction .........................................................................................................................61
Starting the Setup Utility ...................................................................................................61
4.2 Main Setup .........................................................................................................................62
4.3 Advanced ............................................................................................................................64
4.4 Event Logs .........................................................................................................................86
4.5 IPMI ....................................................................................................................................88
4.6 Security ...............................................................................................................................91
4.7 Boot ....................................................................................................................................95
4.8 Save & Exit .........................................................................................................................97
A2SDV-8C/-12C+/-16C-TLN5F User's Manual
7
Preface
Appendix A BIOS Codes
Appendix B Software Installation
B.1 Installing Software Programs ...........................................................................................100
Appendix C Standardized Warning Statements
Battery Handling ..............................................................................................................102
Product Disposal .............................................................................................................104
Appendix D UEFI BIOS Recovery
Appendix E Dual Boot Block
BIOS Boot Block .............................................................................................................110
BIOS Boot Block Corruption Occurrence ......................................................................110
8
A2SDV-8C/-12C+/-16C-TLN5F User's Manual
Main Parts List (included in the retail box)
Description Part Number Quantity
Supermicro Motherboard A2SDV-8C/-12C+/-16C-TLN5F 1
SATA Cables CBL-0044L 2
Quick Reference Guide MNL-2015-QRG 1
I/O Shield MCP-260-00084-0N 1
PCB Spacer for 1U Chassis FST-SCRW-0010 1
Chapter 1
Introduction
Congratulations on purchasing your computer motherboard from an acknowledged leader in
the industry. Supermicro boards are designed with the utmost attention to detail to provide
you with the highest standards in quality and performance.
Please check that the following items have all been included with your motherboard. If
anything listed here is damaged or missing, contact your retailer. The following items are
included in the retail box:
1.1 Checklist
Important Links
For your system to work properly, please follow the links below to download all necessary
drivers/utilities and the user’s manual for your server.
Supermicro product manuals: http://www.supermicro.com/support/manuals/
Product drivers and utilities: ftp://ftp.supermicro.com
Product safety info: http://www.supermicro.com/about/policies/safety_information.cfm
If you have any questions, please contact our support team at: [email protected]m
This manual may be periodically updated without notice. Please check the Supermicro website
for possible updates to the manual revision level.
9
Chapter 1: Introduction
Figure 1-1. A2SDV-8C-TLN5F Motherboard Image
10
A2SDV-8C/-12C+/-16C-TLN5F User's Manual
Figure 1-3. A2SDV-8C-TLN5F Motherboard Layout
(not drawn to scale)
Note: Components not documented are for internal testing only.
BAR CODE
COM2
DESIGNED IN USA
A2SDV-8C-TLN5F
REV:1.02
JIPMB1
JMD2
JMD1
JTGLED1
JPW1
JPI2C1
JSD1
SRW2
SRW3
SRW4
SRW1
JUIDB
JPL1
1
JWD1
JPG1
JBR1
JPME2
JI2C1
JI2C2
DIMMB1
DIMMB2
DIMMA1
DIMMA2
LED1
1
JD1
JSMB1
JGP1
JBT1
JPH1
JPV1
FANB
JTPM1
JNCSI1
JL1
JRT4
1
JRT3
I-SATA1 I-SATA0
UIDLED1
CM CODE
LEDBMC
eUSB
ON
PWR
JF1
RST X
OH/FF
2
NIC NIC
1 LED
HDD
LED
X
PWR
NMI
ALWAYS POPULATE DIMMx1 FIRST
CPU SLOT6 PCI-E 3.0 X8
CPU SLOT7 PCI-E 3.0 X8
VGA
KEY-M PCIE3/SATA3
KEY-B SATA3/USB3
COM1
LAN1(IPMI_LAN)
LAN5
CPU
USB6(3.0)
USB2/3(3.0)
USB0/1(3.0)
USB 4/5
LAN3
FAN4 FAN3
FAN2 FAN1
LAN4/
LAN2/
FANA
SATA DOM POWER
BT1
JF1
BMC AST2400
JPTG1
JSEL1
11
Chapter 1: Introduction
BAR CODE
COM2
DESIGNED IN USA
A2SDV-8C-TLN5F
REV:1.02
JIPMB1
JMD2
JMD1
JTGLED1
JPW1
JPI2C1
JSD1
SRW2
SRW3
SRW4
SRW1
JUIDB
JPL1
1
JWD1
JPG1
JBR1
JPME2
JI2C1
JI2C2
DIMMB1
DIMMB2
DIMMA1
DIMMA2
LED1
1
JD1
JSMB1
JGP1
JBT1
JPH1
JPV1
FANB
JTPM1
JNCSI1
JL1
JRT4
1
JRT3
I-SATA1 I-SATA0
UIDLED1
CM CODE
LEDBMC
eUSB
ON
PWR
JF1
RST X
OH/FF
2
NIC NIC
1 LED
HDD
LED
X
PWR
NMI
ALWAYS POPULATE DIMMx1 FIRST
CPU SLOT6 PCI-E 3.0 X8
CPU SLOT7 PCI-E 3.0 X8
VGA
KEY-M PCIE3/SATA3
KEY-B SATA3/USB3
COM1
LAN1(IPMI_LAN)
LAN5
CPU
USB6(3.0)
USB2/3(3.0)
USB0/1(3.0)
USB 4/5
LAN3
FAN4 FAN3
FAN2 FAN1
LAN4/
LAN2/
FANA
SATA DOM POWER
BT1
JF1
BMC AST2400
JPTG1
JSEL1
Notes:
See Chapter 2 for detailed information on jumpers, I/O ports, and JF1 front panel connec-
tions. Jumpers/LED indicators not indicated are used for testing only.
" " indicates the location of Pin 1.
When JLED1 (Onboard Power LED indicator) is on, system power is on. Unplug the power
cable before installing or removing any components.
Quick Reference
LAN4/5
COM1
USB0/1 (3.0)
LAN1
IPMI
USB2/3 (3.0)
FAN2
FAN3
JL1
JPH1
FANB
USB4/5 eUSB
USB6 (3.0)
DIMMB1
DIMMA1
JPL1
BT1
JTGLED1
JI2C2
JI2C1
JMD2
FAN4
LAN2/3
JPW1
DIMMA2
DIMMB2
JRT3
JSEL1
I-SATA1
JSD1
SRW4
VGA
SRW1
SLOT7
SLOT6
JIPMB1
JWD1
JPI2C1
JPME2
JNCSI1
UIDLED1
LEDBMC
FAN1
JF1
LED1
SRW3
JRT4
FANA
JBR1
JMD1
JUIDB
COM2
JD1
JPG1
JTPM1
SRW2
I-SATA0
JPV1
JBT1
JSMB1
JGP1
JPTG1
12
A2SDV-8C/-12C+/-16C-TLN5F User's Manual
Note: Table is continued on the next page.
Quick Reference Table
Jumper Description Default Setting
JBR1 BIOS Recovery Pins 1-2 (Normal)
JBT1 CMOS Clear Open (Normal)
JI
2
C1/JI
2
C2 SMB to PCI-E Slots Enable/Disable Pins 2-3 (Disabled)
JNCSI1 IPMI Shared LAN Port Selection ON (short): LAN1, OFF (open): LAN2
JPG1 Onboard VGA Enable/Disable Pins 1-2 (Enabled)
JPL1 LAN1 GbE Enable/Disable Pins 1-2 (Enabled)
JPME2 ME Manufacturing Mode Pins 1-2 (Normal)
JPTG1 LAN2/3/4/5 10GbE Enable/Disable Pins 1-2 (Enabled)
JSEL1 PCI-E Slot Selection Pins 1-2: Slot 7, Pins 2-3: Slot 6
JWD1 Watch Dog Timer Pins 1-2 (Reset)
LED Description Status
LED1 Power LED Solid Green: Power On
LEDBMC BMC Heartbeat Blinking Green: BMC Normal
UIDLED1 UID LED Solid Blue: Unit Identied
Connector Description
BT1 Onboard Battery
COM1 COM Port (on the I/O back panel)
COM2 COM Header
FAN1 - FAN4, FANA, FANB System Fan Headers
IPMI_LAN Shared IPMI LAN Port (Default: shared with LAN1)
I-SATA0-1 Intel® PCH SATA 3.0 Ports (I-SATA0: SuperDOM)
JD1 Speaker Header (Pins 1-4: Speaker)
JF1 Front Control Panel Header
JGP1 General Purpose I/O Header
JIPMB1 System Management Bus Header (for IPMI only)
JL1 Chassis Intrusion Header
JMD1 M.2 B-Key PCIE3/SATA3/USB3 Connector
JMD2 M.2 M-Key PCIE3/SATA3 Connector
JPI
2
C1 Power Supply SMBus I
2
C Header
JPH1 4-pin Power Connector for HDD use
JPW1 24-pin ATX Power Connector
JPV1 4-pin 12V DC Power Connector (To provide alternative power for a special enclosure when
the 24-pin ATX power is not in use.)
JRT3 Thermal Diode 1
JRT4 Thermal Diode 2
13
Chapter 1: Introduction
Connector Description
JSD1 SATA Disk On Module (DOM) Power Connector
JSMB1 System Management Bus Header
JTGLED1 LAN4 - LAN5 Activity LED Header
JTPM1 Trusted Platform Module (TPM)/Port 80 Connector
JUIDB1 Unit ID Button
LAN1 - LAN5 LAN1: Gigabit Ethernet (RJ45) Port
LAN2 - LAN5: 10Gigabit Ethernet (RJ45) Ports
SLOT6, SLOT7 PCI-E 3.0 x8 Slots (use SLOT 6 or SLOT 7 only, selectable with JSEL1)
SRW1 - SRW4 M.2 Holding Screws
USB0/1, USB2/3 Back Panel USB 3.0 Ports
USB4/5 Front Accessible USB 2.0 Header
USB6 USB 3.0 Type A Header
VGA VGA Port
14
A2SDV-8C/-12C+/-16C-TLN5F User's Manual
Note: The table above is continued on the next page.
Motherboard Features
CPU
Intel® Atom SoC C3000 Series (FCBGA1310) Processor
Memory
Supports up to 256GB of RDIMM and 64GB of Non-ECC/ECC UDIMM DDR4 memory with speeds of up to 2400MHz.
On select SKUs, 2400MHz modules can be used but will operate at a lower speed.
DIMM Size
4GB, 8GB, 16GB, 32GB, and 64GB
Expansion Slots
Two (2) PCI-E 3.0 x8 slots option (SLOT6 or SLOT 7 only)
One (1) M.2 PCI-E 3.0 x2 slot (M-Key)
One (1) M.2 PCI-E 3.0 x2 slot (B-Key)
Network
Intel i210AT Gigabit Ethernet Controller
Intel X557-AT4 10Gigabit Ethernet Controller
Baseboard Management Controller (BMC)
ASpeed AST2400 Baseboard Controller (BMC) supports IPMI 2.0
One (1) IPMI LAN port (shared with Intel i210AT LAN1)
Graphics
Graphics controller via ASpeed AST2400 BMC
I/O Devices
Serial (COM) Port One (1) RJ45 serial port (COM1) on back panel
Serial (COM) Header One (1) serial header (COM2)
SATA 3.0 Four (4) SATA 3.0 ports (two via the M.2 connector)
Peripheral Devices
Four (4) USB 3.0 ports on the I/O back panel (USB0/1/2/3)
Two (2) USB2.0 ports in one internal header (USB4/5)
One (1) USB 3.0 Type A header (USB6)
BIOS
128Mb AMI BIOS® SPI Flash BIOS
Plug and Play (PnP), SPI dual/quad speed support, real time clock (RTC) wakeup, ACPI 3.0, BIOS rescue hot-key, and
SMBIOS 2.7
Motherboard Features
15
Chapter 1: Introduction
Motherboard Features
Power Management
ACPI power management
CPU fan auto-off in sleep mode
Power button override mechanism
Power-on mode for AC power recovery
System Health Monitoring
Onboard voltage monitors for CPU cores, +3.3V, +5V, +12V, +3.3V Stby, +5V Stby, VBAT, Memory, PCH temperature,
system temperature, and memory temperature
Status monitor for on/off control
CPU Thermal Trip support
Fan Control
Fan status monitoring via IPMI connections
Low noise fan speed control
Dual cooling zone
System Management
PECI (Platform Environment Control Interface) 3.1 support
IPMI 2.0 (shared with LAN1)
SuperDoctor® 5, Watch Dog, NMI
Chassis Intrusion header and detection
Power supply monitoring
LED Indicators
Power / suspend-state indicator LED
UID / Remote UID
HDD activity LED
LAN activity LED
Other
RoHS
Dimensions
FlexATX form factor (9" x 7.25") (228.6 mm x 184.15 mm)
Note 1: The CPU maximum thermal design power (TDP) is subject to chassis and
heatsink cooling restrictions. For proper thermal management, please check the chas-
sis and heatsink specications for proper CPU TDP sizing.
Note 2: For IPMI conguration instructions, please refer to the Embedded IPMI Con-
guration User's Guide available at http://www.supermicro.com/support/manuals/.
16
A2SDV-8C/-12C+/-16C-TLN5F User's Manual
Note: This is a general block diagram and may not exactly represent the features on
your motherboard. See the previous pages for the actual specications of your moth-
erboard.
Figure 1-4.
Chipset Block Diagram
PCIE X8 SLOT 6
M.2 2242/2280 M KEY
PCIe 3.0 x2 (8GT/s)
SATA 3.0 x1 (6GT/s)
USB 3.0 x1 / USB 2.0 x1
USB 3.0 x1
USB 2.0 x1
USB 2.0 x1
USB 3.0 x1
(OPTION)
2400MHz
DDR4 (CHA)
DIMMA1,A2
DDR4 (CHB)
DIMMB1,B2
2400MHz
AST2400
COM2 HEADER
TPM1.2 Header
LPCHSIO[8] , PCIE X1
SVID
VR13
VGA
PCIE/SATA SSD
USB 3.0/2.0
MICRO SIM
M.2 3042/2280 B KEY
PCIe 3.0 x2 (8GT/s)
SATA 3.0 x1 (6GT/s)
PCIE X8 SLOT 7
PCIe 3.0 x8
8GT/s
HSIO[7:0] , PCIE x8
HSIO[13:12] , PCIE x2
PCIE/SATA SSD
SATA-III
6Gb/s
HSIO[17:16] , SATA III
RGMII2
SGPIO[1]
2X SATA-III
USB2.0[3]
USB 2.0 [0]
FCBGA1310
C3000 Series
SMBUS2
USB3.0 HUB1
USB3.0
+
USB3.0
USB3.0
USB3.0
HSIO[18] , USB 3.0
HSIO[19] , USB 3.0
USB3.0 HUB2
USB2.0[2]
HEADER USB2.0 X2
TYPE-A USB3.0
COM1
UART2
UART1
HSIO[15:14] , PCIE x2
HSIO[10] , PCIE X1
X557-AT4
KR X4, PORT 0,1
FAN X6
RGB
TACHOMETER
I210AT 1Gb NIC
*2.5 (GT/s)
PCIE 3.0 X1
LAN1
BMC
REAR REAR
Intel
17
Chapter 1: Introduction
1.2 Processor Overview
The Intel Atom C3000 series processor, with 16 cores and up to 31W of power, offers
performance, reliability, and high intelligence. As a low-power system-on-a-chip motherboard,
the A2SDV-8C/-12C+/-16C-TLN5F is optimized for a variety of workloads that include
networking and cloud storage.
ACPI Power Management Logic Support Rev. 4.0a
Intel QuickAssist Technology
Adaptive Thermal Management/Monitoring
PCI-E 3.0, SATA 3.0 and M.2 (B-Key and M-Key) connectors
System Management Bus (SMBus) Specication Version 2.0
Intel VT-x with Extended Page Tables (EPT)
Intel Virtualization Technology (VT-x)
Intel Virtualization Technology for Directed I/O (Intel VT-d)
1.3 Special Features
This section describes the health monitoring features of the A2SDV-8C/-12C+/-16C-TLN5F
motherboard. The motherboard has an onboard System Hardware Monitor chip that supports
system health monitoring.
Recovery from AC Power Loss
The Basic I/O System (BIOS) provides a setting that determines how the system will respond
when AC power is lost and then restored to the system. You can choose for the system to
remain powered off (in which case you must press the power switch to turn it back on), or
for it to automatically return to the power-on state. See the Advanced BIOS Setup section
for this setting. The default setting is Last State.
1.4 System Health Monitoring
This section describes the health monitoring features of the A2SDV-TLN5F Series
motherboard. The motherboard has an onboard Baseboard Management Controller (BMC)
chip that supports system health monitoring. Once a voltage becomes unstable, a warning
is given or an error message is sent to the screen.
18
A2SDV-8C/-12C+/-16C-TLN5F User's Manual
Onboard Voltage Monitors
The onboard voltage monitor will continuously scan crucial voltage levels. Once a voltage
becomes unstable, it will give a warning or send an error message to the screen. Users can
adjust the voltage thresholds to dene the sensitivity of the voltage monitor. Real time readings
of these voltage levels are all displayed in BIOS.
Fan Status Monitor with Firmware Control
The system health monitor embedded in the BMC chip can check the RPM status of the
cooling fans. The CPU and chassis fans are controlled via lPMI.
Environmental Temperature Control
System Health sensors monitor temperatures and voltage settings of onboard processors
and the system in real time via the IPMI interface. Whenever the temperature of the CPU or
the system exceeds a user-dened threshold, system/CPU cooling fans will be turned on to
prevent the CPU or the system from overheating
Note: To avoid possible system overheating, please provide adequate airow to your
system.
System Resource Alert
This feature is available when used with SuperDoctor 5® in the Windows OS or in the Linux
environment. SuperDoctor is used to notify the user of certain system events. For example,
you can congure SuperDoctor to provide you with warnings when the system temperature,
CPU temperatures, voltages and fan speeds go beyond a predened range.
1.5 ACPI Features
ACPI stands for Advanced Conguration and Power Interface. The ACPI specication denes
a exible and abstract hardware interface that provides a standard way to integrate power
management features throughout a computer system, including its hardware, operating
system and application software. This enables the system to automatically turn on and off
peripherals such as CD-ROMs, network cards, hard disk drives and printers.
In addition to enabling operating system-directed power management, ACPI also provides a
generic system event mechanism for Plug and Play, and an operating system-independent
interface for conguration control. ACPI leverages the Plug and Play BIOS data structures,
while providing a processor architecture-independent implementation that is compatible with
Windows® 2012.
19
Chapter 1: Introduction
1.6 Power Supply
As with all computer products, a stable power source is necessary for proper and reliable
operation. It is even more important for processors that have high CPU clock rates.In areas
where noisy power transmission is present, you may choose to install a line lter to shield the
computer from noise. It is recommended that you also install a power surge protector to help
avoid problems caused by power surges. For the A2SDV-8C/-12C+/16C-TLN5F motherboard,
please use a power supply that supports 2.5A or above on 5V standby.
1.7 Serial Port
The A2SDV-8C/-12C+/-16C-TLN5F motherboard supports two serial communication
connection. COM port 1 (RJ45 socket) and COM port 2 (internal header) can be used for
input/output. The UART provides legacy speeds with a baud rate of up to 115.2 Kbps as well
as an advanced speed with baud rates of 250 K, 500 K, or 1 Mb/s, which support high-speed
serial communication devices.
20
A2SDV-8C/-12C+/-16C-TLN5F User's Manual
Chapter 2
Installation
2.1 Static-Sensitive Devices
Electrostatic Discharge (ESD) can damage electronic com ponents. To prevent damage to your
motherboard, it is important to handle it very carefully. The following measures are generally
sufcient to protect your equipment from ESD.
Precautions
Use a grounded wrist strap designed to prevent static discharge.
Touch a grounded metal object before removing the board from the antistatic bag.
Handle the board by its edges only; do not touch its components, peripheral chips, memory
modules or gold contacts.
When handling chips or modules, avoid touching their pins.
Put the motherboard and peripherals back into their antistatic bags when not in use.
For grounding purposes, make sure your computer chassis provides excellent conductivity
between the power supply, the case, the mounting fasteners and the motherboard.
Use only the correct type of onboard CMOS battery. Do not install the onboard battery
upside down to avoid possible explosion.
Unpacking
The motherboard is shipped in antistatic packaging to avoid static damage. When unpacking
the motherboard, make sure that the person handling it is static protected.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111

Supermicro A2SDV-16C-TLN5F User manual

Category
Server/workstation motherboards
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI