Readings may be unstable. Wait for
steady state to be reached (LED
changes from red to green).
Save “as
found” data.
Press ENTER
to analyze.
Summary screen is
displayed
Highlight fuel
from fuel list.
Press ENTER.
Go to MAIN
MENU.
Highlight
TUNE-RITE™.
Press ENTER.
Read and
Accept
Disclaimer.
Highlight
Appliance
Type from list.
Press ENTER.
Highlight the
analysis you
want.
From the
summary
screen,
press NEXT
to show
results list.
Scroll through
results list.
Now stable and
within limits.
Press LIST to
review what
was done.
data.
Press NEXT
for results.
Readings within
acceptable ranges.
BACHARACH, INC.
621 Hunt Valley Drive New Kensington, PA 15068
800-736-4666 [email protected]
www.Tune-Rite.com www.MyBacharach.com
Display bar graphs.
Power on.
Connect probe assembly to analyzer.
Press ENTER.
Always “zero” the analyzer in fresh air.
Select FUEL from MAIN MENU.
Gas
G
Gas
G
U
N
S
T
A
B
L
E
S
T
E
A
D
Y
S
T
A
T
E
Stable, outside range
Unstable
Stable, inside range
Red: Not Ready
Green: Ready
Consult the INSIGHT™
Manual for probe
Press ENTER.
Watch pointers for status of each parameter.
Outside limits shown (red pointers).
Display values screen.
Analyzing...
Press ENTER to
cycle through
Press BACK to
re-analyze.
Press INFO for
more informa-
P/N: 0024-9505
Revision 0 July 2014
© 2014 Bacharach, Inc.
It’s INSIGHT® Plus... plus much, much more.
s
s
Report records may
now be selected and
printed.
IMPORTANT: Before using Tune-Rite™,
be sure to read the following:
appliance manufacturer.
T
u
n
e
-
R
i
t
e
™
P
a
t
e
n
t
P
e
n
d
i
n
g
Scroll through
possible cause list.
Highlight cause to
Press ENTER to see
-
associated with the
selected cause.
IMPORTANT: Inspect, adjust,
and/or repair the appliance
based on safety guidelines,
-
ance manufacturer’s
system guidance from Tune-
Rite™. Refer to the INSIGHT®
further safety details.
LIGHT
OFF
STEADY
STATE
ANALYZE
OKAY?
Steady State
Not Reached*
Watch the dynamic graph to
reach steady-state.
The dynamic graph, status
dot, and status arrows
Review analysis.
checklist, build report,
then print analysis.
ADJUST/
REPAIR
Major Repairs Required?
Consult All Associated
Test
Save
Data
Save
Data
Menu
Tune-Rite Results
Overfired
List
Analyze
Heat Exchanger
Burner
Readings in Range
Unresolved
Smoke Test
(Oil Only)
If steady-state is not reached,
repairs, or replacement.
Save “As Found” data.
Press “Enter” to analyze.
If readings are outside
of limits, review priori-
causes.
If possible causes are
indicated, repair/adjust
of possible causes.
progress of all possible
causes using check boxes.
Review all readings in
-
ing ranges. One sample
(CO reading) is shown
below.
unable to reach typical
repairs or replacement.
*
Menu
Run Nat Gas
Save
Saved to memory
location 24
Menu
Run Nat Gas
Save
Analyzing...
Readings in Range
Overfired
Heat Exchanger
Burner
RESULT A: Inside Range
RESULT B: Outside Range
tuned (problems
resolved/readings in
range).
Back
Burner
Dirty Pilot
Flame Impingement
Dirty Burner
Burner Debris
s
t
side
rior
i
-
Menu
Run Nat Gas
Print
Save
Waiting for
steady-state.
0 500
14
0 500
339
Back
Burner
Dirty Pilot
Flame Impingement
Dirty Burner
Burner Debris
Me
nu
Li
s
t
A
nal
y
z
e
I
f
p
ossible causes are
indicated, re
p
air/ad
j
ust
of
p
ossible causes
.
Bu
rn
er
D
irt
y
Pilo
t
D
irt
y
Burne
r
, , and
Back
Checklist
Print
Save
Cracked Heat Ex
Dirty Burner
Gas Pressure
Flame Impingement
Red: Not Ready
Green: Ready
Red:
Yellow:
Green:
Stable, outside range
Unstable
Stable, inside range
Next
Tune-Rite Summary
6.0 9.0
375 550
0 100
8.5
500
339
WAIT ANALYZE INVESTIGATE TRACK REVIEW SUMMARIZE
Menu
Tune-Rite Results
List
Analyze
CO Unstable
Menu
Run Nat Gas
6.0 9.0
375 550
0 100
8.5
500
10
Save
Menu
Run Nat Gas
6.0 9.0
375 550
0 100
8.5
500
10
Save
Save
Info
Info
As Found DataService Checklist
ec
kli
s
t
,
b
u
ild
re
p
or
t
,
en
p
rint anal
y
sis.
Fuel
Nat. Gas
=========================
As Found Condition:
Time: 03:46:21 PM
Date: 04/09/14
Fuel
Nat. Gas
As Left Condition:
Time: 07:09:28 PM
Date: 04/09/14
Service Checklist
Time: 07:09:57 PM
Date: 04/09/14:
Gas Pressure
Cracked Heat Ex
Dirty Burner
Flame Impingement
Burner Debris
BACHARACH, Inc.
Insight Plus
SN: AB1234
O
2
8.5 %
CO 339 ppm
Eff 76.0 %
CO
2
7.0 %
T-Stk 500
o
F
T-Air 80.0
o
F
EA 61.0 %
CO(O) 571 ppm
O
2
8.0 %
CO 14 ppm
Eff 76.8 %
CO
2
7.3 %
T-Stk 490
o
F
T-Air 80.0
o
F
EA 55.0 %
CO(O) 23 ppm
Print
Print
BACHARACH’S
Fyrite® Tune-Rite™
!!!
SEE HOW TUNE-RITE
™
FITS INTO YOUR
COMBUSTION ANALYSIS PROCESS
A “when-you-need-
integrated with the
Fyrite® INSIGHT® Plus
analyzer
Guidance based on
live data and typical
-
process
A detailed, custom-
izable, and value-added
service report for the
customer
service technician
/
