ESC02
ELECTRIC SCOOTER
USER MANUAL
CAUTION: Please read the operating instructions before riding.
Any child must be accompanied by an adult while using this
scooter. In Australia, each state and territory has specic
regulations that may apply to this product, including where
you can legally use such products and if you need to register
them with your local road trafc authority. Please be sure to
familiarise yourself with these prior to using this product.
ESC02 3
PRODUCT OVERVIEW
CONTROL PANEL
WHAT’S IN THE BOX
ASSEMBLY AND SETUP
CHARGING YOUR SCOOTER
FOLDING PROCEDURE
SAFETY WARNINGS
CARE & MAINTENANCE
SPECIFICATIONS
TRADEMARK & LEGAL STATEMENT
CERTIFICATIONS
IGNITE APP QUICK SETUP
04
05
06
07
08
09
11
12
13
15
ESC02 5
PRODUCT OVERVIEW CONTROL PANEL
1
4
6
10 1211
8
9
7
5
2 3
# ACCESSORY/PART # ACCESSORY/ PART
1Accelerator 7Rear Mudap
2Control Panel 8Brake Light
3Scooter Bell 6Disc Brake
4Headlight 10 Charging Port
5Brake Lever 11 Battery Compartment
6Folding Mechanism 12 Kickstand
ACCESSORY/ PART QTY
ESC02 Electric Scooter 1
Charging Adapter 1
Hexagon Wrench 1
Screws 4
WHAT’S IN THE BOX
The battery level is indicated by ve power bars on the control panel. As the battery level
is depleted these bars will turn off. Below the battery bars is the speed in km/h or MPH.
Battery level display
When the bottom battery bar ashes, it indicates the scooter has low power. If possible
stop all use of the scooter and plug in the charger until the battery is fully charged.
If the scooter does run out of power, all lights will turn off, and the scooter will coast
until it comes to a complete stop.
Power button
Press and hold the power button for two seconds to turn on/off the scooter; After turning
on, quickly press the power button twice to turn on/off the headlight; and quickly press
three times to change the units between MPH and km/h.
ESC02 7
1. Fasten the handlebar stem on the base
and put the kickstand down.
2. Attach the handlebar to the stem.
1. Lift up the rubber ap on
the base of the scooter.
2. Plug the power adapter
into the charging port.
3. When completed, remove
the charger and cover
with the rubber ap.
3. Tighten the screws onto both sides of
the stem with the supplied Allen key.
4. When the assembly is complete, press
the power button to ensure the scooter
& control panel work correctly.
ASSEMBLY AND SETUP CHARGING YOUR SCOOTER
FOLDING PROCEDURE
Turn the Scooter off, to fold up, unlock the folding clamp, and fold the handlebars back
towards the rear mudguard.
For ease of transport, once the Scooter is folded it can be carried by the handlebar stem.
ESC02 9
1. In Australia, each state and territory has specic regulations that may apply to this product,
including where you can legally use such products and if you need to register them with your
local road trafc authority. Please be sure to familiarise yourself with these prior to using this
product.
2. When operating this scooter, a helmet and other protective equipment are required.
3. This scooter is not engineered for skatepark or stunting use. Please keep both hands on the
handlebars at all times.
4. This scooter is not designed to be used
off-road. Only ride on at and paved surfaces. Avoid riding on or through sand, gravel, mud,
rugged or open ground. Do not ride on slippery surfaces, such as snow, ice or oil.
5. Do not use this scooter below -5°C or in wet conditions.
6. Before each use, ensure all bolts and screws are secure & tight.
7. Keep ngers, hairs, and clothing away from motors, wheels and any moving parts.
8. Do not open or tamper with the frame or control panel as this will void the warranty.
This electric scooter is for private use only. When used in a public area, please follow the
specic regulations for your state/territory.
This scooter has a top speed of 25km/h, please take into account stopping distances when
traveling in public at these speeds. Please use caution when approaching pedestrians as a
collision can cause serious injury to both the rider and pedestrian.
Check the scooter before each use. Upon inspection, if there are loose parts, low battery alerts,
at or excessive wear on the tyres, or any other abnormal conditions, do not use the scooter
and contact IGNITE customer support if required.
Aquilia Group Pty Ltd. shall not be liable for any nancial losses, physical injuries, accidents, legal
disputes and other interest conicts resulted from actions that violate the user instruction manual.
SAFETY WARNINGS CARE & MAINTENANCE
CLEANING & STORAGE
When not in use, store the scooter in a dry and cool location. Do not leave the scooter
exposed to direct sunlight or in a damp/wet location. This can accelerate tyre aging,
corrosion, or even compromise the battery pack.
To clean the scooter use a damp cloth and wipe away the dirt & debris. Ensure the power
is turned off and the charging cable is unplugged with the rubber ap is securely closed
to prevent any moisture from getting into the electronic components. Do not pressure
wash the scooter as this will cause the electronic systems to fail. Alcohol, gasoline,
kerosene or other corrosive and volatile chemical solvents should also be avoided when
cleaning the scooter.
BATTERY MAINTENANCE
Only original parts are permitted to be used in the scooter. Any third-party batteries or
accessories can cause a failure & will void the warranty.
Do not store the scooter in a location where the ambient temperature is higher than 50°C
or lower than -20°C, this includes leaving the scooter in in a car under direct sunlight for
an extended time.
If the scooter is left for long periods of time between uses, it is recommended to fully
charge the battery before the next use. Charging the battery before it is depleted can
help prolong the life of the battery.
NOTE: Charging the battery takes ~5-6 hours. Each battery has a built-in chip that
records a log of charging and discharging times. If the battery is left depleted for a
prolonged period of time it will be unable to be recharged and not covered by the
standard warranty.
11ESC02
ADJUSTING THE DISC BRAKE
If the disc brake is too tight, use the supplied Allen key to loosen the screws on the
caliper, and readjust the brake cable. Shortening the exposed cable will cause the
brake to use less pressure. Lengthening the cable will cause the brake to become
more responsive.
ADJUSTING THE HANDLEBARS
If the handlebars and stem sway during use, use provided Allen key to tighten the screws
on the folding mechanism.
ACCESSORY/ PART QUALITY ISSUE
Model ESC02
Color Black
Max Speed 25km/h
Maximum grade Approx. 14°
General Range 15-25km
Rider Age Min: 16 | Max: 55
Rider Weight Min: 25kg | Max: 100kg
Battery
Rated Voltage Max. 36 (VDC)
Input Voltage 42 (VDC)
Rated capacity 328 (WH)
Charger
Input Voltage 100-240 (VAC)
Charging Time ~6 hours
Wheel Construction 10” Solid Rubber
Braking method Rear Disc Brake
Dimensions
Scooter size (L x W x H) 1090 × 430 × 1150mm
Scooter folded (L x W x H) 1090 × 430 × 500mm
Weight
Net Weight 14.8 kg
Gross Weight 16.6 kg
[1] ITEM HEIGHT: from the ground to the top of the scooter;
[2] GENERAL RANGE: measured when it is no wind and at 30°C, the scooter’s fully charged to ride at a even speed of 20km/h
on a at surface with a load of 165 pounds.
NOTE: data and specications may vary due to different models, and are subject to change without notice.
SPECIFICATIONS
CARE & MAINTENANCE
Control your Electric Scooter using
the IGNITE App.
1. Scan the QR code below or go to your phones
App Store to download.
2. Once downloaded, activate your Bluetooth,
open the APP and pair your scooter.
3. When the scooter and phone are paired,
the screen will show.
IGNITE APP QUICK SETUP
12ESC02
/
