Swivel Pro
Complete Upright Vacuum
NV150 Series
OWNER’S GUIDE
Navigator®
sharkclean.comsharkclean.com
GENERAL WARNINGS
1. Your vacuum cleaner may consist of
a motorized nozzle, wand, hose, and/
or vacuum pod. This device contains
electrical connections, electrical
wiring, and moving parts that
potentially present risk to the user.
2. Use only identical replacement parts.
3. Carefully observe and follow the
instructions provided below to avoid
improper use of the appliance. DO
NOT use the vacuum for any purpose
other than those described in this
manual.
4. Before use, carefully inspect all parts
for any damage. DO NOT use if any
parts are damaged.
5. The use of an extension cord is NOT
recommended.
6. This vacuum cleaner contains no
serviceable parts.
USE WARNINGS
7. This appliance can be used by
persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Cleaning and user maintenance shall
not be made by children.
8. Keep the appliance and its cord out
of reach of children. DO NOT allow
the appliance to be used by children.
DO NOT allow to be used as a toy.
Close supervision is necessary when
used near children.
9. Always turn off the vacuum cleaner
before connecting or disconnecting
any motorized nozzles or other
accessories.
10. DO NOT handle plug or vacuum
cleaner with wet hands.
11. DO NOT use without filters in place.
12. Only use Shark® branded filters and
accessories. Failure to do so will also
void the warranty.
13. DO NOT damage the power cord:
a) DO NOT pull or carry vacuum
cleaner by the cord or use the cord
as a handle.
b) DO NOT unplug by pulling on cord.
Grasp the plug, not the cord.
c) DO NOT run the vacuum cleaner
over the power cord, close a door
on the cord, pull the cord around
sharp corners, or leave the cord
near heated surfaces.
14. DO NOT put any objects into nozzle
or accessory openings. DO NOT use
with any opening blocked; keep free
of dust, lint, hair, and anything that
may reduce airflow.
15. DO NOT use if nozzle or accessory
airflow is restricted. If the air paths or
the motorized floor nozzle become
blocked, turn the vacuum cleaner
off and unplug from electrical outlet.
Remove all obstructions before you
plug in and turn on the unit again.
16. Keep nozzle and all vacuum
openings away from hair, face,
fingers, uncovered feet, or loose
clothing.
WARNING
To reduce the risk of fire, electric shock, injury, or property damage:
IMPORTANT SAFETY INSTRUCTIONS
FOR HOUSEHOLD USE ONLY • PLEASE READ CAREFULLY BEFORE USE
If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. DO NOT force into outlet or try to modify to fit.
To reduce the risk of electric shock, this appliance has a polarized plug (one blade
is wider than the other). This plug will fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper outlet. Do not change the plug in any way.
SAVE THESE INSTRUCTIONS
17. DO NOT use if vacuum cleaner is not
working as it should, or has been
dropped, damaged, left outdoors, or
dropped into water.
18. Use extra care when cleaning
onstairs.
19. DO NOT leave the vacuum cleaner
unattended while plugged in.
20. When powered on, keep the
vacuum
cleaner moving over the
carpet surface
at all times to avoid
damaging the carpet fibers.
21. DO NOT place vacuum cleaner on
unstable surfaces such as chairs
or tables.
22. Your Shark® vacuum may not be
designed to stand up on its own.
When taking a break from cleaning,
you may need to lean it against
furniture or a wall, or lay it flat
on the floor. Using the vacuum
for an application where the
unit lacks stability may result in
personalinjury.
23. DO NOT use to pick up:
a) Liquids
b) Large objects
c) Hard or sharp objects
(glass, nails, screws, or coins)
d) Large quantities of dust (drywall
dust, fireplace ash, or embers).
DO NOT use as an attachment to
power tools for dust collection.
e) Smoking or burning objects (hot
coals, cigarette butts, or matches)
f) Flammable or combustible
materials (lighter fluid, gasoline,
or kerosene)
g) Toxic materials (chlorine bleach,
ammonia, or drain cleaner)
24. DO NOT use in the following areas:
a) Poorly lit areas
b) Wet or damp surfaces
c) Outdoor areas
d) Spaces that are enclosed and may
contain explosive or toxic fumes
or vapors (lighter fluid, gasoline,
kerosene, paint, paint thinners,
mothproofing substances, or
flammable dust)
25. Turn off all controls before plugging
in or unplugging the vacuum.
26. Unplug from electrical outlet
when not in use and before any
maintenance or cleaning.
27. Hand wash with water only. Washing
with cleaning chemicals could
damage the unit.
28. During cleaning or routine
maintenance, DO NOT cut anything
other than hair, fibers, or string
wrapped around the brushroll.
29. Allow all filters to air-dry completely
before replacing in the vacuum to
prevent liquid from being drawn into
electric parts.
30. Make sure the dust cup and all
filters are in place after routine
maintenance.
31. If provided, secure the power cord
around the two cord hooks during
storage.
sharkclean.comsharkclean.com
ASSEMBLY ASSEMBLY
POWER CORD
For cord access, rotate upper hook down
and remove cord.
Use cord holder on the side of wand to hold
cord in place while vacuuming.
UPPER CORD HOOK CORD HOLDER
1
(Click)
2
(Click)
1. Insert the Wand into the Pod.
2. Insert the Handle into the top of the wand.
3. Connect the Hose to the back of the pod.
4. Insert the C-clip into the back of the pod.
5. Insert the hose into the C-clip and the hose holder.
6. Store Accessories on the Tool Storage Posts.
For proper operation, ensure all parts are firmly clicked into place.
3
(Click)
4
(Click)
5(Click)
6
sharkclean.comsharkclean.com
NOTE: All accessories are compatible with both the wand and the handle.NOTE: For deep carpet cleaning per ASTM F608 (embedded dirt in carpets), set to MAX suction and use setting II, Carpet.
WHOLE-HOME CLEANING
CLEANING MODES
To engage Brushroll, step on floor nozzle
and tilt handle back firmly.
Select surface setting:
O O
I Hard Floor
For bare floors and area rugs. The brushrolls will
spin slowly in this mode.
II Carpet
For carpets. The brushrolls spin quickly in this
mode.
To engage the brushrolls, turn on the power,
step on the floor nozzle, and tilt the handle back.
WHAT DOES THE BRUSHROLL INDICATOR LIGHT MEAN?
Solid Green: The brushroll is spinning and working as intended.
Solid Red: There is a jam in the brushroll area. Turn o and unplug the vacuum and remove
any blockages in the nozzle.
Flashing Red: The motorized floor nozzle is overheating. Turn the vacuum o and wait a
minimum of 60 minutes for the unit to cool down. See Troubleshooting section for more
information.
Press the Wand Release button and pull up on
the wand to detach it from the pod.
Press the Handle Release button and pull up on
the handle to detach it from the wand.
Attach a cleaning accessory to handle or wand.
UPRIGHT MODE
POWER/SURFACE SWITCH
INDICATOR LIGHT
ABOVE-FLOOR—WAND
ACCESSORIES—WAND
ABOVE-FLOOR—HANDLE
ACCESSORIES—HANDLE
WHOLE-HOME CLEANING
SETTINGS
BRUSHROLL INDICATOR LIGHT
The Suction Control Slider located on the handle
allows you to adjust the suction depending on
the floor type.
MIN: to reduce suction and increase
maneuverability on carpets.
MAX: to increase suction on bare floors.
SUCTION CONTROL
sharkclean.comsharkclean.com
EMPTYING THE DUST CUP
To remove Dust Cup, slide up the release button
on the dust cup handle. Tilt dust cup forward,
then lift to remove.
To reinstall, place the bottom of dust cup
onto the pod and then tilt until it clicks into
place.
Press the release button to open bottom of
dust cup.
To remove collected debris from Lint Screen,
press the top release button and lift the
handle to open the dust cup. Gently brush
lint screen toclean.
RINSE HEPA FILTER
EVERY YEAR
Remove dust cup, tilt Filter Door and firmly
pull it o. Press tab at top of HEPA Filter and
pull out filter. To reinstall, insert HEPA filter
into unit and replace the filter door.
RINSE PRE-MOTOR FILTERS
EVERY MONTH
Remove Dust Cup, then lift out Filters.
Regularly rinse and replace the filters to maintain your vacuum's suction power.
To prevent damage from cleaning chemicals, rinse filters with cold water only. Allow all filters
to air-dry for at least 24 hours before reinstalling them to prevent liquid from being drawn into
electronicparts.
CLEANING AND REPLACING THE FILTERS
CLEANING FILTERS
IMPORTANT: DO NOT use soap when cleaning the filters.
IMPORTANT: Unplug the power cord before performing any maintenance.
Empty the dust cup each time you vacuum and periodically during cleaning,
when debris in the dust cup reaches the MAX fill line.
Post-Motor
HEPA Filter
Foam
Felt Filter
Door
NOTE: The pre-motor filters should be replaced every 2.5 years. The post-motor filter should be replaced every 3 years.
sharkclean.comsharkclean.com
Clean o any debris on the bristles.
Using a coin, turn locks counterclockwise, then lift the cover to access brushroll.
If you run over a hard or sharp object or
notice a noise change while vacuuming, check
for blockages or objects caught behind the
brushroll.
Clear away any dust, dirt, or blockages in
Debris Intake.
To close the cover, push down until it clicks into
place. Close the locks by using a coin to turn
them clockwise.
DEBRIS WRAPPED AROUND BRUSHROLL DEBRIS BEHIND BRUSHROLL
CLEANING THE BRUSHROLL
MAINTENANCE CHECKING FOR BLOCKAGES
Detach hose from vacuum pod, and check hose
and opening on back of pod for blockages.
Detach wand from pod and handle, and check both
ends for blockages.
Detach wand from pod, and check opening
for blockages.
Detach handle from wand and hose from the
vacuum pod, and check openings for blockages.
Detach dust cup from vacuum pod. Empty dust
cup, remove debris from lint screen, and check for
blockages.
HOSE BLOCKAGES WAND BLOCKAGES
POD BLOCKAGES HANDLE/HOSE BLOCKAGES
DUST CUP BLOCKAGES
sharkclean.comsharkclean.com
AVAILABLE ACCESSORIES TROUBLESHOOTING
Vacuum is not picking up debris. No suction or light suction.
• Check filters to see if they need cleaning. Follow instructions for rinsing and air-drying the
filters before reinstalling them.
• Dust cup may be full; empty dust cup.
• Check hose, hose connections, nozzle, wand, pod, and accessories for blockages. Clear any
blockages found.
• If any string, hair, or carpet fibers are wrapped around the brushroll, remove the floor nozzle
cover and use scissors to carefully cut away debris. See Cleaning the Brushroll section for
more information.
Vacuum lifts area rugs.
• Make sure Power/Surface switch is set to Hard Floor (setting I).
• Rotate suction control slider to MIN.
• Suction is powerful. Take care when vacuuming area rugs or rugs with delicately sewn
edges.
Brushroll does not spin.
• If the Brushroll Indicator Light turns red, immediately turn o and unplug the vacuum. Lay
the unit down and turn over so the brushroll is facing up. Using a coin, turn the 3 locks on
the bottom of the nozzle to access the brushroll. Remove any hair or blockages from the
nozzle. Reinstall the brushroll cover and turn all 3 locks back to the locked position.
• With the power on, recline the handle, which will automatically turn on the brushroll.
Vacuum turns o on its own or indicator light flashes red.
If your vacuum overheats, the thermostat will automatically turn the suction motor o. Perform
the following steps to restart:
1. Turn vacuum o and unplug it.
2. Empty dust cup and clean filters (see Emptying the Dust Cup and Cleaning and Replacing
the Filters).
3. Check for blockages in hose, accessories, wand, nozzle, and inlet openings.
4. Allow unit to cool for a minimum of 60 minutes.
5. Plug in vacuum and restart with the Power/Surface switch.
For all other issues, please call Customer Service 1-800-798-7398.
B
GH
I J
F
E
D
A Crevice Tool
This slender tool oers extended reach to
access corners, baseboards, tight spaces,
and ceilings.
B Duster Crevice Tool
Two cleaning tools in one. The crevice tool
gives you extended reach to clean in tight
spaces, while the soft brush is ideal for
dusting delicate surfaces.
C Dusting Brush
This brush dusts and cleans delicate
surfaces. Great for use on fans, blinds,
lampshades, and keyboards.
D Upholstery Tool
Picks up hair, dust, and large debris from
mattresses, couches, curtains, lampshades,
and other delicate upholstered fabrics.
E Pet Multi-Tool
A single convertible tool for cleaning tough
pet messes two ways: use the sti bristle
brush to clean stuck-on debris, or take o
the bristles to reveal an upholstery tool
perfect for removing stubborn pet hair and
large piles of debris.
F Pet Power Brush
The turbine brush loosens and removes
pet hair and debris from carpets, and
powerfully deep-cleans dander out of
upholstery and other surfaces.
G Under-Appliance Wand
Clean under and behind hard-to-move
appliances and furniture with this adjustable
36” tool. Flip the extension piece over to
clean the underside of appliances.
H Anti-Allergen Dust Brush
This brush features nylon fiber bristles
specifically designed for removing fine
dust and allergen particles from the most
delicate surfaces.
I Home & Car Detail Kit
Deep-clean your car like a professional
detailer, or clean hard-to-reach areas in
your home. Micro-sized tools let you clean
around delicate objects and access the
tightest spaces like car vents and computer
keyboards.
J Accessory Bag
This convenient accessory storage bag
measures 32 cm x 70 cm and fits the Under-
Appliance Wand. Smaller size available at
sharkaccessories.com.
A
C
NOTE: Not all accessories come with all units. For a list of the accessories included with this model, see the top inside flap
of the box. To order additional accessories, visit sharkaccessories.com.
sharkclean.comsharkclean.com
FIVE (5) YEAR LIMITED WARRANTY
TECHNICAL SPECIFICATIONS
Voltage: 120V, 60Hz
Watts: 700W
Amps: 5.8A
TIP: You can find the model and serial
numbers on the QR code label on the
bottom of the back of the vacuum pod.
Benefits of registering your product and
creating an account:
• Get easier, faster product support and
access to warranty information
• Access troubleshooting and product care
instructions
• Be among the first to know about
exclusive product promotions
RECORD THIS INFORMATION
Model Number:
����������������������������������������������������������������������������������������������������
Serial Number:
������������������������������������������������������������������������������������������������������
Date of Purchase:
��������������������������������������������������������������������������������������������
(Keep receipt)
Store of Purchase:
������������������������������������������������������������������������������������������
REGISTER YOUR PURCHASE
registeryourshark.com
Scan QR code using
mobile device
The Five (5) Year Limited Warranty applies to purchases made from authorized retailers of SharkNinja
Operating LLC. Warranty coverage applies to the original owner and to the original product only and is
not transferable.
SharkNinja warrants that the unit shall be free from defects in material and workmanship for a period
of five (5) years from the date of purchase when it is used under normal household conditions and
maintained according to the requirements outlined in the Owner’s Guide, subject to the following
conditions and exclusions:
What is covered by this warranty?
1. The original unit and/or non-wearable components deemed defective, in SharkNinja’s sole discretion,
will be repaired or replaced up to five (5) years from the original purchase date.
2. In the event a replacement unit is issued, the warranty coverage ends six (6) months following the
receipt date of the replacement unit or the remainder of the existing warranty, whichever is later.
SharkNinja reserves the right to replace the unit with one of equal or greater value.
What is not covered by this warranty?
1. Normal wear and tear of wearable parts (such as foam filters, HEPA filters, pads, etc.), which require
regular maintenance and/or replacement to ensure the proper functioning of your unit, are not covered
by this warranty. Replacement parts are available for purchase at sharkaccessories.com.
2. Any unit that has been tampered with or used for commercial purposes.
3. Damage caused by misuse (e.g., vacuuming up water or other liquids), abuse, negligent handling,
failure to perform required maintenance (e.g., not cleaning the filters), or damage due to mishandling
in transit.
4. Consequential and incidental damages.
5. Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused
in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the
repair is performed by a repair person not authorized by SharkNinja.
6. Products purchased, used, or operated outside North America.
How to get service
If your appliance fails to operate properly while in use under normal household conditions within the warranty
period, visit sharkclean.com/support for product care and maintenance self-help. Our Customer Service
Specialists are also available at 1-800-798-7398 to assist with product support and warranty service options,
including the possibility of upgrading to our VIP warranty service options for select product categories.
SharkNinja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee of
$24.95 (subject to change) will be charged when SharkNinja ships the repaired or replacement unit.
How to initiate a warranty claim
You must call 1-800-798-7398 to initiate a warranty claim. You will need the receipt as proof of purchase.
A Customer Service Specialist will provide you with return and packing instruction information.
How state law applies
This warranty gives you specific legal rights, and you also may have other rights that vary from state to
state. Some states do not permit the exclusion or limitation of incidental or consequential damages, so
the above may not apply to you.
© 2020 SharkNinja Operating LLC. SHARK and SHARK NAVIGATOR are registered trademarks
of SharkNinja Operating LLC. NAVIGATOR is a trademark of SharkNinja Operating LLC.
NV150Series�IB�REV�Mv4
PRINTED IN CHINA
PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.
This Owner’s Guide is designed to help you get a complete understanding of your new
Shark Navigator® Swivel Pro Complete Upright Vacuum.
SharkNinja Operating LLC
US: Needham, MA 02494
CAN: Ville St-Laurent, QC H4S 1A7
1-800-798-7398
sharkclean.com
Illustrations may dier from actual product. We are constantly striving to improve our products;
therefore the specifications contained herein are subject to change without notice.
For SharkNinja U.S. Patent information, visit sharkninja.com/uspatents
/