HitLights LED Strip Lights 32.8ft Color Changing Tape Lights SMD 5050 300LEDs Flexible RGB Light Strips User manual

Brand: HitLights

Model: LED Strip Lights 32.8ft Color Changing Tape Lights SMD 5050 300LEDs Flexible RGB Light Strips

Type: User manual

This manual is also suitable for

USB LED TV Backlight, Bendable RGB Light Strip

1/2. Turn On/off

Turn unit on/Off. When powered on,unit will restore

the previous status setting.

1. Using Remote Controller

Remove Plastic tab before using. Remote’s signal can pass

through many barriers. To properly receive remote signal,

do not install the main unit within enclosed metal parts.

2. Paring New Remote

Remote is paired to reciever by default. A receiver can be

paired to 2 remotes. Remotes can be paired to any receiver.

If a receiver be paired to 3 remotes, the 3rd remote will

cover the 1st. Follow steps below to pair a new remote.

1. Turn On

2. Turn Off

4. Speed adjust +

5. Speed adjust -

3. Auto mode

6. Modes switch +

7. Modes switch -

8.Brightness adjust +

9.Brightness adjust -

3. Switch Output color sequence

The controller's default output signal sequence is

Blue-Red-Green. If the led application is in a different

cable sequence, the direct color won't match the led

color. In this case, you can adjust the output signal

sequence with the following steps.

With this operation, output sequence will be memorized.

Static Color Mode: [Red], [Green], [Blue], [Purplish Red]

[Light Green], [Light Blue], [Orange], [Purple], [Cyan],

[yellow], [Lavender], [White]

Modes list

Automatically plays 19 dynamic modes in a loop.

3. Auto mode

S+to increase speed, S- to decrease.

This key only works in dynamic mode.

4/5. Speed adjust

Switch to dynamic mode from static color, or switch

between static mode.

6/7. Dynamic modes switch

Press to increase brightness and to decrease.

This key only works in dynamic mode.

8/9. Brightness adjust

Dynamic Mode: [Red fade],[Green fade],[Blue fade]

[Yellow fade],[Purple fade], [Cyan fade], [White fade]

[Red fade+jump], [Green fade+jump],[Blue fade+jump]

[Red flash],[Green flash],[Blue flash],[3 colors jump]

[7 colors jump],[3 colors alteranting flash],

[Dazzling mode],[3 colors fade],[7 colors fade]

Working temperature: -20-60°C

Input voltage: DC5-24V

Output: 3 circuit

Connection mode: Common anode

Controller size: L55.7×W16.6×H10.7mm

RF frequency: 433.92Mhz

Static power consumption: <0.5W

Output current: <2A*3CH(each circuit)

Output power: 5V:<30W

12V:<72W

24V:<144W

Controller distance: 20-30M

2.2 Press ' 'for 2 seconds and the receiver will recognize

the new remote controller.

3.1 Turn off the led strip light, then press ' ' 5 times,

the led strip light will now be lit.

3.2 Press Red ' ', sequence will be Red-Green-Blue.

Press Green ' ', sequence will be Green-Red- Blue.

Press Blue' ', sequence will be Blue- Red- Green.

Then new sequence will now be used.

Remember to remove plastic tab.

2.1 Disconnect reciever from power, reconnect within 5 sec.

HitLights LED Strip Lights 32.8ft Color Changing Tape Lights SMD 5050 300LEDs Flexible RGB Light Strips User manual

Brand: HitLights

Model: LED Strip Lights 32.8ft Color Changing Tape Lights SMD 5050 300LEDs Flexible RGB Light Strips

HitLights LED Strip Lights 32.8ft Color Changing Tape Lights SMD 5050 300LEDs Flexible RGB Light Strips User manual

This manual is also suitable for

HitLights LED Strip Lights 32.8ft Color Changing Tape Lights SMD 5050 300LEDs Flexible RGB Light Strips User manual

Other documents