Wattstopper
®
Quick Connect Wiring Harness
Installation Instructions • Instructions d’Installation • Instrucciones de Instalación
No: 25225 – 11/16 rev. 1
Catalog Number • Numéro de Catalogue • Número de Catálogo: LMBC-300-H6
Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China
DESCRIPTION
The LMBC-300-H6 Quick Connect Wiring Harness provides BACnet connection for up to 6 LMBC-300s, mounted to a DIN rail. Each
end of the harness has the (S) Shield wire connected, while the connectors for each individual LMBC-300 have the (S) Shield wire
twisted and securely wrapped around the wire jacket with heat shrink. Since up to 40 LMBC-300s can be connected in a BACnet
segment, use of the LMBC-300-H6 allows for a minimum number of terminations in a properly wired BACnet network.
The harness contains 6 male terminal blocks for connection to LMBC-300s, plus a male terminal block on one end and female terminal
block on the other end. The harness also includes additional pre-attached male and female terminal blocks, for use when connecting to
LM-MSTP cable. Remove these terminal blocks to connect to another LMBC-300-H6.
Step 1 Remove Connectors from the LMBC-300s
Unscrew and unplug the connectors from each LMBC-300.
Attached
Connector
Step 2 Attach DIN Rail Mounting Bracket
Screw mounting bracket (included with LMBC-300) into
back of the LMBC-300.
Step 3 Attach LMBC-300s to DIN Rail
Attach up to 6 LMBC-300s to an 18” DIN rail, by
pulling spring-loaded handle and fitting clip into rail.
Step 4 Attach Harness Connectors to
LMBC-300s
Plug connectors on the LMBC-300-H6 into
each LMBC-300, securing each connector by
screwing it in.
NOTE: Do not connect the male terminal
block at the end of the harness to
an LMBC-300. This terminal block is
used only to extend the segment by
connecting to LM-MSTP cable or an
additional LMBC-300-H6, or to end the
segment by connecting to a terminal
block with an end-of-line resistor.
NOTE: If connecting fewer than 6 LMBC-300s
to the harness, place LMBC-300s at
both ends of the harness to prevent
slack in the middle, as shown in the
drawing on the next page.
Step 5 Connect BACnet Cable or Another Harness
If connecting the harness to LM-MSTP cable, attach the cable to the
extra male terminal block, as shown below. Repeat at the other end with
the extra female terminal block.
NOTE: Wattstopper recommends the use of ferrules to connect wires to
the terminal block, as described on the next page.
If connecting to another LMBC-300-H6, remove the appropriate extra
terminal block from each harness and connect the two.
If this harness is at the end of the segment, an EOL (End of Line)
120Ω resistor must be installed on the extra female terminal block, as
shown below.
(R) Green with
White Stripe
LM-MSTP cable wired to Male
Terminal Block (included in package)
OR
Additional LMBC-300-H6
Female Terminal Block
at end of harness
S
+
R
S
+
-
R
(+) White
(-) Black
(S) Shield
-
Ferrule
S
+
-
R
Top View End View
Male Female
120Ω
120Ω
S
+
R
S
+
R
-
-
Installing an EOL Resistor
Connecting LM-MSTP cable
or another LMBC-300-H6
800.879.8585
www.legrand.us/wattstopper
No. 25225 – 11/16 rev. 1
© Copyright 2016 Legrand All Rights Reserved.
© Copyright 2016 Tous droits réservés Legrand.
© Copyright 2016 Legrand Todos los derechos reservados.
Wattstopper warranties its products to be free
of defects in materials and workmanship for a
period of five (5) years. There are no obligations
or liabilities on the part of Wattstopper for
consequential damages arising out of, or in
connection with, the use or performance of this
product or other indirect damages with respect
to loss of property, revenue or profit, or cost of
removal, installation or reinstallation.
Wattstopper garantit que ses produits sont
exempts de défauts de matériaux et de fabrication
pour une période de cinq (5) ans. Wattstopper
ne peut être tenu responsable de tout dommage
consécutif causé par ou lié à l’utilisation ou
à la performance de ce produit ou tout autre
dommage indirect lié à la perte de propriété, de
revenus, ou de profits, ou aux coûts d’enlèvement,
d’installation ou de réinstallation.
Wattstopper garantiza que sus productos
están libres de defectos en materiales y mano
de obra por un período de cinco (5) años. No
existen obligaciones ni responsabilidades por
parte de Wattstopper por daños consecuentes
que se deriven o estén relacionados con el
uso o el rendimiento de este producto u otros
daños indirectos con respecto a la pérdida
de propiedad, renta o ganancias, o al costo
de extracción, instalación o reinstalación.
WARRANTY INFORMATION INFORMATIONS RELATIVES À LA GARANTIE INFORMACIÓN DE LA GARANTÍA
Shield is Twisted & Heat Shrunk
(Not Connected to Terminal)
Connect to another
LMBC-300-H6
or to LM-MSTP
cable
with Male
Terminal
Block (in package)
Female
Terminal Block
DIN Mounting Bracket
Male
Terminal Block
S
+
-
R
S
+
R
LMBC-300 LMBC-300
Connect to another
LMBC-300-H6
or to LM-MSTP cable
with Female Te
rminal
Block (in package)
If end of line, attach
120Ω resistor
S
+
R
S
+
R
-
-
-
18” DIN Rail
LMBC-300
If fewer than 6 LMBC-300s
are connected, place one at
each end to prevent slack
in cable
Shield connected to
Terminal Block at
each end of harness
Shield connected to
Terminal Block at
each end of harness
Example of LMBC-300-H6 Installed With LMBC-300s
1.25"
0.50"
Bare Wire
Insulation Strip Guide
*Legrand recommends using Ferrules,
but if not using, wire should be stripped to .25” only
Attaching a Ferrule
Crimp
Ferrule
Insulation
Jacket
LM-MSTP wire
Attaching Ferrules to LM-MSTP Wires
Wattstopper recommends attaching ferrules to the LM-MSTP wires to
help maintain signal integrity. Wires should be stripped as shown in the
diagram to the right. Insert the wire into a ferrule and crimp the end,
using a crimping tool designed to work with ferrules. Then insert the end
of the ferrule into the appropriate slot in the terminal block.
R
+
-
S
R
+
-
S
R
+
-
S
R
+
-
S
Room 1 Room 2 Room 3 Room 4 Room 5 Room 6Electrical Closet
Room 7 Room 8 Room 9 Room 10 Room 11 Room 12
Segment Manager
or
Segment Manager
with NB-Router
LM-MSTP cable (BACnet)
CAT-5e cable (DLM Network)
To
additional LMBC-300-H6s
Room
Controller
LMBC-300-H6 with 6 LMBC-300s
Room
Controller
LMBC-300-H6 with 6 LMBC-300s
Example of hallway and rooms using networked LMBC-300-H6s
-
1
-
2
Legrand LMBC-300-H6 Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Legrand LMBC-300-H6 Guide d'installation
Related papers
-
Legrand LMSM-3E/6E Installation guide
-
Legrand DLM N4 JACE8000-SM Installation guide
-
Legrand LMJA-8xxx Installation guide
-
-
-
-
-
-
-
