Toro Auxiliary Control Kit, 762 Backhoe for RT1200 Trencher Installation guide

Brand: Toro

Model: Auxiliary Control Kit, 762 Backhoe for RT1200 Trencher

Type: Installation guide

Toro Auxiliary Control Kit, 762 Backhoe for RT1200 Trencher will enable you to control certain functions of your machine directly from the backhoe. Specifically, this device will allow you to:

Start and stop the engine
Raise and lower the backfill blade
Control the forward and backward movement of the machine
Control the engine speed

The kit is easy to install and comes with all the necessary parts. Once installed, the auxiliary control kit will give you greater control over your machine and make it easier to operate.

Here are some possible use cases for the Toro Auxiliary Control Kit:

Toro Auxiliary Control Kit, 762 Backhoe for RT1200 Trencher will enable you to control certain functions of your machine directly from the backhoe. Specifically, this device will allow you to:

Start and stop the engine
Raise and lower the backfill blade
Control the forward and backward movement of the machine
Control the engine speed

The kit is easy to install and comes with all the necessary parts. Once installed, the auxiliary control kit will give you greater control over your machine and make it easier to operate.

Here are some possible use cases for the Toro Auxiliary Control Kit:

FormNo.3378-123RevA

AuxiliaryControlKit

762BackhoeforRT1200Trencher

ModelNo.25467

ModelNo.25467E

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Removetheconsolepanel.

Startbutton

Rockerswitch3

Installthestartbuttonandrockerswitches.

Nopartsrequired

–

Connectthebackhoewiringtothebuttonandswitches.

Nopartsrequired

–

Installtheconsolepanel.

RemovingtheConsolePanel

1.Parkthemachineonalevelsurfaceandlowerthe

backhoetotheground.

2.Shutofftheengine,andremovethekeyfromthekey

switch.

3.RotatethebatterydisconnectswitchtotheOff

position;refertotheOperator’sManualforthemachine.

4.Removethe4hex-headbolts(3/8x1inch)and4

washers(3/8inch)thatsecuretheconsolepaneltothe

operatorconsoleforthebackhoe(Figure1).

Figure1

1.Consolepanel3.Washer(3/8inch)

2.Operatorconsole4.Bolt(3/8x1inch)

5.Removethe3rectangularplugsfromtheconsolepanel

(Figure2).

Note:Discardthe3plugsafterremoval.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3378-123*A

Figure2

1.Rectangularplugs

2.Consolepanel

InstallingtheStartButtonand

RockerSwitches

1.Removethejamnutfromthestartbutton(Figure3).

Figure3

1.Consolepanel

3.Jamnut

2.Startbutton

4.Rockerswitch

2.Inserttheelectricalconnector,wires,andcaseofthe

startbuttonthroughthe15.8mm(5/8inch)holein

theconsolepanel(Figure3).

3.Securethestartbuttontotheconsolepanelwiththe

jamnut(Figure3)thatyouremovedinstep1.

4.Alignthe3rockerswitchedtothe3rectangular

openingsintheconsolepanel,andsnapthemintothe

panel(

Figure3).

Note:Ensurethatthealignmentkeyfortheswitchis

pointingtotheforwardedgeofthepanel.

ConnectingtheBackhoe

WiringtotheButtonsand

Switches

1.Connectthe10-socketconnectorofthebackhoe

wiringharnessthatislabeledThrottletothe10-pin

connectoroftheinboardrockerswitch(Figure4).

Note:Thisistherockerswitchthatisclosesttothe

startbutton.

Figure4

1.E-stopbutton

5.Outboard

rockerswitch

(propel)

9.2-pinconnector

(backhoe

wiringharness)

2.Startbutton6.Screw

10.10-socket

connector

(throttle)

3.Inboardrocker

switch(throttle)

7.Forkedterminal11.10-socket

connector

(backllblade)

4.Centerrocker

switch(backll

blade)

8.2-socket

connector(start

button)

12.10-socket

connector

(propel)

2.Connectthe10-socketconnectorofthebackhoewiring

harnessthatislabeledBladetothe10-pinconnector

ofthecenterrockerswitch(Figure4).

3.Connectthe10-socketconnectorofthebackhoewiring

harnessthatislabeledPropeltothe10-pinconnector

oftheoutboardrockerswitch(Figure4).

4.Connectthe2-pinconnectorofthebackhoewiring

harnesstothe2-socketconnectorofthestartbutton

(

Figure4).

5.Afteralloftheconnectionsaremade,verifythatthe

seatswitchandtheE-stopfunctionproperlybefore

operatingthemachine.

InstallingtheConsolePanel

1.Applymediumgrade(serviceremovable)thread

lockingcompoundtothethreadsofthe4hex-head

bolts(3/8x1inch)thatyouremoveinstep4of

RemovingtheConsolePanel.

2.Alignthemountingholesintheconsolepanelwiththe

mountingholesintheoperatorsconsole(Figure1).

3.Securethepaneltotheconsolewiththe4hex-head

boltsand4washers,andtorquethebolts51to65N-m

(38to48lb-ft).

4.RotatethebatterydisconnectswitchtotheOn

position;refertotheOperator’sManualforthemachine.

Operation

Theauxiliarycontrolkitisusedwiththebackhoetocontrol

theforwardandbackwardmovementofthemachine,the

enginespeed,andtheelevationofthebackllblade—from

theoperatorspositiononthebackhoe.

StartingandControllingthe

Engine

1.Fromtheoperatingposition,ensurethatallofthe

controlsareintheNeutralposition,andthekeyswitch

intheOnposition;refertotheOperator’sManualfor

themachine.

Note:Iftheengineiscold,thewait-to-start-engine

indicatorwilldisplayinthecommandcenter.Wait

fortheengineheatertowarmtheengineinletbefore

movingtothebackhoe.

2.Sitintheoperatorseatforthebackhoe.

3.Pressthestartbutton(Figure5).

Note:Ensurethatallofthebackhoecontrolsare

intheNeutralpositionbeforestartingtheengine,or

suddenmotionoftheattachmentmayoccur.

Note:Iftheenginestartsandthenstops,donot

startbuttonagainuntilthestartermotorhasstopped

turning.

Important:

Do not

operatethestartermotoruntil

itstopsturning.

Do not

operatethestartermotor

formorethan30secondsatonetime.Allowthe

startermotortocoolfor2minutesbeforeyou

operateitagain.Whenyouengagethestarter

motor,youshouldseewhiteorblacksmoke

comingfromtheexhaustpipe;ifyoudonot,check

thefuelsupply.

Figure5

1.Propel-rockerswitch

4.Startbutton

2.Backll-bladerocker

switch

5.E-stopbutton

3.Throttle-rockerswitch

4.Usethethrottle-rockerswitchtocontroltheengine

speedasfollows:

•Pressuponthethrottle-rockerswitchtoraisethe

enginespeed(Figure5).

•Pressdownonthethrottle-rockerswitchtolower

theenginespeed(

Figure5).

5.Shuttheengineoffasfollows:

Important:Intheeventofanemergency,press

theE-stopbuttonimmediately.

A.Lowertheenginespeedtoidlebypressingdown

onthethrottle-rockerswitch(Figure5).

Note:Allowtheenginetoidlefor3to5minutes.

B.PresstheE-stopbuttontoshutofftheengine

(Figure5).

C.Aftertheenginestops,resettheE-stop.

D.TurnthekeytotheOffpositionattheoperator

positionforthemachine.

RaisingandLoweringthe

BackllBlade

Usethebackll-bladerockerswitchtoraiseandlowerthe

backllbladeasfollows:

1.Pressdownontheupperhalfoftheblade-rocker

switchtoraisethebackllblade(

Figure5).

2.Pressdownonthelowerhalfoftheblade-rocker

switchtolowerthebackllblade(Figure5).

MovingtheMachineForward

orBackward

Usethepropel-rockerswitchtomovethemachineforward

orbackwardasfollows:

1.Raisethebackllblade;refertoRaisingandLowering

theBackllBlade(page4).

2.Raisetheleftandrightstabilizersofthebackhoe;refer

totheOperator’sManualforthebackhoeattachment.

3.Lowerthethrottletoidle;refertoStartingand

ControllingtheEngine(page3).

4.Usethepropel-rockerswitchtomovethemachine

forwardorbackwardasfollows:

A.Pressuponthepropel-rockerswitchtomovethe

machineforward(Figure5).

B.Pressdownonthepropel-rockerswitchtomove

themachinebackward(

Figure5).

5.Onceyouareatthenewlocationwhereyouintendto

usethebackhoe,lowerthestabilizersandbackllblade;

refertoRaisingandLoweringtheBackllBlade(page

4)andtheOperator’sManualforthebackhoeattachment.

Note:Donotmovethemachinetooclosetoahole,

especiallyifonsoftground.

Toro Auxiliary Control Kit, 762 Backhoe for RT1200 Trencher Installation guide

Brand: Toro

Model: Auxiliary Control Kit, 762 Backhoe for RT1200 Trencher

Type: Installation guide

Toro Auxiliary Control Kit, 762 Backhoe for RT1200 Trencher will enable you to control certain functions of your machine directly from the backhoe. Specifically, this device will allow you to:

Start and stop the engine
Raise and lower the backfill blade
Control the forward and backward movement of the machine
Control the engine speed

The kit is easy to install and comes with all the necessary parts. Once installed, the auxiliary control kit will give you greater control over your machine and make it easier to operate.

Here are some possible use cases for the Toro Auxiliary Control Kit:

Download PDF

report

Toro Auxiliary Control Kit, 762 Backhoe for RT1200 Trencher Installation guide

Toro Auxiliary Control Kit, 762 Backhoe for RT1200 Trencher Installation guide

Related papers

Other documents