Royal Sovereign ARP-1200M User manual

Brand: Royal Sovereign

Model: ARP-1200M

Category: Mobile air conditioners

Type: User manual

This manual is also suitable for

Air Conditioner ARP-1200M

Royal Sovereign ARP-1200M is a portable air conditioner that can cool, dehumidify, and circulate air in rooms up to 400 square feet. It features two fan speeds, adjustable louvers for directing airflow, a 24-hour timer, and a remote control for added convenience. The ARP-1200M also has an energy-saving mode that automatically adjusts its cooling power based on the ambient temperature, and a washable and reusable air filter to help keep the air clean.

Royal Centurian Inc.

ARP-1200M / ARP-1200DM / ARP-1200E / ARP-1200DE

OWNER’S MANUAL

MANUAL DEL PROPIETARIO

PORTABLE AIR CONDITIONER

ACONDICIONADOR DE AIRE PORTÁTIL

Read and retain these instructions for future reference

Lea y tenga presente estas instrucciones para futuras consultas

PORTABLE AIR CONDITIONER

Model ARP-1200M / ARP-1200DM / ARP-1200E / ARP-1200DE

BEFORE USE

GENERAL SAFETY

• Only use in the upright position on a flat, level surface at least 20”/50cm from any object (fig 1 & 4).

• Do not place objects on the unit or restrict air inlet / outlet (fig. 2).

• Closely supervise children and pets while unit is in use.

ELECTRICAL SAFETY

• For indoor use only.

• Turn off and unplug the unit when it is not in use.

• Do not use in wet environments (fig 3).

• Do not pull the unit by the cord.

• If the supply cord is damaged, it must be replaced by an

electrician or qualified person, to avoid hazard or injury.

FOR MAXIMUM EFFICENCY

• Do not exceed the recommended room size 400 sq. feet.

• Close doors and windows.

• Keep curtains or blinds closed during the sunniest

part of the day.

• Keep filters clean.

• Once room has reached the desired conditions, reduce

temperature and ventilation settings.

FIG.3

FIG.1 FIG.2

FIG.4

ARP-1200M / ARP-1200DM

ARP-1200E / ARP-1200DE

Front

1. Control Panel

2. Air outlet

3. Carrying handle

4. Caster

Back

5. Air filter

6. Air inlet

7. Exhaust air outlet

8. Cord storage &

power cord with

LCDI breaker plug

and reset buttons.

9. Water stopper /

drainage point

PARTS

Accessories

10. Air Conditioner adaptor - for insertion over hose and into back of the air conditioner.

11. Window adaptor - for insertion over hose and into window spacer.

12. Exhaust hose

13. Extendable window spacer.

14. Drain tube for continuous drainage

15. Water tray

16. Remote control (for electronic type only)

ARP-1200M / ARP-1200DM

ARP-1200E / ARP-1200DE

INSTALLATION

Installation of the exhaust pipe

The unit is a portable air conditioner that may be moved from room to room.

Please follow the steps for installation:

1. Feed the outward adapter through the extendable window spacer.

2. Screw the exhaust hose into the outward adapter.

3. Insert the window spacer into window gaps as shown.

Adjust its length if necessary.

4. Slide window across so that the spacer is held securely.

NOTE: Take care to maintain protection against intruders

NOTE: Install window vent vertically or horizontally depending on window style.

Window Spacer may be cut to fit. If window spacer does not fill opening

completely a custom made spacer from your local home improvement store

can be made.

Extendable

window

spacer

FIG.5

FIG.6

FIG.7

Outward Adapter

Mounting of the exhaust pipe

• Using only the hose provided, screw unit adapter to exhaust hose then clip the unit adaptor to the back of the air conditioner.

• Avoid kinks and bends in the exhaust hose as this will cause expelled moist air to build up causing the

unit to overheat and shut down. (Fig 8 & 9 show correct position).

NOTE: For best results do not exceed a 45º angle.( Fig 10)

• The hose may be extended from 1-5 ft /300mm -1500mm but for maximum efficiency use the shortest straightest length possible.

It is not recommended to exceed 5 feet for this will diminish the efficiency of the unit. See WARNING Figure 11

WARNING

The length of the exhaust pipe is specially designed according to the

specification of this product. Do not replace or lengthen it with your own

hose as this will cause the unit to malfunction.

FIG.8 FIG.9 FIG.10

FIG.11

Installation of the carbon filter

1. Remove the filter frame from the unit.

2. Separate the filter fixer from the filter frame.

3. Remove the active carbon filter from its plastic bag.

4. Insert the active carbon filter into the filter frame.

5. Fix the filter by reassembling the fixer to the filter frame.

6. Re-fit the filter frame inside the unit.

1. Power indicator

2. Fan operating indicator

3. Cooling operating indicator

4. 'Full water' indicator

5. Heating operating indicator (ARP-1200DM only)

6. Timer (1-8 hours) as well as ON/OFF Switch

7. Speed switch with options for - FAN, LOW COOL, HIGH COOL, LOW HEAT, HIGH HEAT.

8. Thermostat

OPERATION for mechanical unit

ARP-1200M/ ARP-1200DM

FIG.12

ARP-1200M / ARP-1200DM

ARP-1200E / ARP-1200DE

Turning ON/OFF

Set the TIMER to ON position for continuous operation (the unit will operate as long as it is not turned off).

Power indicator comes on.

To turn off the unit, turn the TIMER to the OFF position.

Setting function / ventilation speed

Cooling only models (ARP-1200M and ARP-1200E)

Turn the speed switch to select required setting: LOW FAN, HIGH FAN, LOW COOL, HIGH COOL

Cooling & heating models (ARP-1200DM and ARP-1200DE)

Turn the speed switch to select required setting: FAN, LOW COOL, HIGH COOL, LOW HEAT, HIGH HEAT

Setting temperature

Turn the THERMOSTAT to regulate the temperature desired: The cooling intensity increases clockwise..

Set timer

Set the TIMER to the desired operating time (1 to 8 hours). When the set time has been reached, the machine will shut off automatically.

Regulating air flow direction

Turn the roller on the air vent to control the air flow direction of the vertical louvers.

Move the air vent directly to adjust the air flow direction of the horizontal louvers.

NOTE: 1. To lengthen the compressor's life, when the unit is turned off wait at least 3 minutes before turning it back on.

2. The cooling system will turn off if the ambient temperature is lower than the set one. The ventilation, however,

keeps working on the set level. If the ambient temperature rises above the selected level, the cooling function will resume.

3. On the contrary, the heat will turn off if the ambient temperature is higher than the set one (still, the ventilation keeps working on

the set level). As the ambient temperature drops below the selected level, the heating function will resume.

4. This machine is equipped with an ANTI-FROST function. While using the heating function in low temperatures, sometimes the

heat will stop for a while in order to melt the frost. As this occurs, just wait for the heating function to resume.

FIG.13

FIG.14

FIG.15

Turning ON/OFF

Press ON/OFF button, the unit will start automatically. If the ambient temperature is

- Higher than 75

F / 24

C, the unit will work in cooling mode.

- Higher than 68

F / 20

C, but below or equal to 75

F / 24

C, the unit will work in ventilation mode.

- Below 68

F / 20

C, the unit will work in heating mode (Only for units ARP-1200 DM/DE)

Indicators of the functions in progress will be lit. *NOTE: The COMPRESSOR indicator will only light up when the compressor is in operation.

The display window shows the ambient room temperature.

To turn the unit off, press the ON/OFF button again.

Setting mode/function

Press MODE button to select required working mode: automatic, cooling, fan or heating,

(heating is only available for units ARP-900DE and ARP-900DM). The indicator of your selected mode will be lit.

Auto mode is factory preset at 75 degrees. When in auto mode(auto and cool light illuminated) the temp up and temp down buttons are

disabled and you cannot set a desired temperature. If you want a desired temperature above or below 75 run unit in cool mode and set your

desired temperature by pressing the temp up or temp down buttons.

OPERATION for electronic unit

Control panel

1. 'Heating operation indicator (For ARP-DM, ARP-DE)

2. Fan operation indicator

3. Cooling operation indicator

4. Automatic mode indicator

5. ' Set temperature' indicator

6. 'Room temperature' indicator

7. High ventilation indicator

8. Low ventilation indicator

9. Timer operation indicator

10. Sleep function indicator

11. Compressor operation indicator

12. Mode (function) option button

13. 'Temperature up' button

14. 'Temperature down' button

15. Speed (ventilation) button

16. Sleep button

17. Timer button (1~12 hours)

18. ON/OFF(power) button

19. Receiver

20. Display window

FIG.16

ARP-1200M / ARP-1200DM

ARP-1200E / ARP-1200DE

Setting temperature

Press the 'Temperature up' or 'Temperature down' button to regulate the temperature desired.

The display window will show the temperature which you have set as you press the 'Temperature up' or 'Temperature down' button.

Otherwise, it will always show the ambient temperature.

The preset temperature of this machine is: 75

F / 24

C / for cooling, 68

F / 20

C for heating.

Setting ventilation speed

1. Press the SPEED button to choose the ventilation speed needed, high or low. The indicator of high or low

ventilation will light up at the same time.

2. If the unit is in AUTO mode, it will choose the ventilation speed automatically according to the ambient temperature (the related

indicators will light up: at this time, the speed switch is invalid).

Setting timer

1. Press the TIMER button to set the operating hours desired (1 to 12 hours, the timer indicator will light on).

When the set time has been reached, the machine will turn off automatically.

The display window will show the hour(s) you set as you press the TIMER button. If the timer button is not pressed,

the unit will work continuously.

2. By pressing the timer but without turning on the other functions, you can PRESET the time for the machine to start.

For example, if you press the timer to '2', the unit will start automatically after 2 hours.

Sleep function

1. By pressing the SLEEP button, the set temperature will increase 2

F /1

C / in the 1st hour, another 2

F / 1

C in the second hour,

then remains at that temperature.

2. By pressing the SLEEP button again, the temperature setting will return to the pre-selected one.

3. The unit will automatically turn off after the SLEEP function runs for 12 hours.

All the above functions can also be performed with the supplied remote control.

The remote control requires 2 AAA batteries to operate.

FIG.17

Regulating air flow direction

Turn the roller on the air vent to control the air flow direction of the vertical louvers.

Move the air vent directly to adjust the air flow direction of the horizontal louvers.

NOTE: 1. To lenghten the compressor's life, after turning off the unit, please wait at

least 3 minutes before turning it back on.

2. The cooling system will switch off if the ambient temperature is lower than the set one. The ventilation, however, keeps working at the

set level. If the ambient temperature rises above the selected level, the cooling function will resume.

3. On the contrary, the heat will switch off if the ambient temperature is HIGHER than the set one (still, the ventilation keeps working at

the set level). As the ambient temperature drops below the selected level, the heating fu nction will reume.

4. This machine is equipped with ANTI-FROST function. While using the heating function in low temperatures, sometimes the heat will

stop for a while in order to melt the frost. As this occurs, just wait for the heating function to resume.

DRAINAGE

Although the unit is self evaporating, during high humidity levels excess water may fill the internal water tray. Depending on how high the humidity

and the duration of high humidity levels will depend on how often the unit needs to be drained. When the reservoir full :

a. For the mechanical model, the compressor will stop, only the fan ill continue to circulate the air. The 'FULL WATER' indicator will light up.

b. For the electronic model, both of the compressor and motor will stop. The COMP. indicator light will flash.

To resume the cooling function, empty the water by the following steps:

1. Turn off the air conditioner and avoid moving it when full.

2. Position the water tray underneath the drain hole.

3. Remove the drain knob & rubber plug from the drain hole and allow the water to drain out.

4. When the water tray is almost full, replace the rubber plug in the drain hole and empty

the water tray.

5. Repeat until the unit is emptied.

6. Replace the rubber plug and tighten the drain knob firmly.

7. Turn on the unit - the comp light should not be flashing.

FIG.18

FIG.19

ARP-1200M / ARP-1200DM

ARP-1200E / ARP-1200DE

Drain hole

Rubber plug

Drain knob

If you wish to operate the unit without the need to empty the water tank, please:

• Remove the drain knob and rubber plug and retain for future use.

• Connect the drain tube supplied to the water outlet as shown and locate

the other end into a drain.

• The drain tube may be extended by adding an extension tube and using a

suitable connector.

Please note

1. The drain must be at or below the outlet level.

2. Flashing comp / 'full water' indicator will not function in this mode of drainage.

3. If you want to extend the water tube, you can connect it with another tube

(OD: .7" / 18mm)

Caution for heating function:

While using the heating function, please note:

1. In heat mode the exhaust MUST be exhausted to the outside just as in air conditioning

mode. The unit works in reverse of air conditioning mode with the warm air out the front

and cold air is exhausted out the back.

2. Fix the drainage to be a continuous one (i.e. drain the water by water tube).

3. Working range for heating function is 41

- 80.6

F (5

- 27

C) and for the cooling

function, it is 64

- 89

F (18

- 32

C). For temperatures outside of this range, the

unit will not work properly.

rubber plug

drain knob

drain tube

original water tube

FIG.20

FIG.21

FIG.22

MAINTENANCE

Always unplug the air conditioner from the outlet before cleaning.

To maximize the efficiency of the air conditioner clean regularly.

Cleaning the housing

Use a soft, damp cloth to wipe the body clean.

Never use chemicals, gasoline, detergents, chemically treated cloths, or other cleansing solutions, as such could possibly damage the cabinet.

Cleaning the filter

Use a vacuum cleaner or tap the filter lightly to remove loose dust and dirt, then rinse thoroughly under running water (no hotter than 104

F/40

C).

Dry thoroughly before replacing.

NOTE: Never operate the unit without the filters.

End of season storage

• Drain any water from the unit. Operate the unit in fan mode only for a few hours to thoroughly dry the inside.

• Clean or change the filter.

• Unplug and store the power cord as shown

• Replace in the original carton or cover for storage..

• Always maintain the unit in an upright position.

FIG.23

ARP-1200M / ARP-1200DM

ARP-1200E / ARP-1200DE

Cord

TROUBLE SHOOTING

* Never try to repair or dismantle the unit yourself

The compressor doesn't run:

Too noisy:

The machine seems to do nothing:

The machine seems to do little:

The air conditioner does not run:

•

It is possible that the overheat protection of the compressor is on. Just wait for the

temperature to drop.

•

Is the machine positioned unevenly Creating Vibration?

•

Is the floor underneath the machine uneven?

•

Is the filter dusty or contaminated?

•

Is the air intake or output blocked up?

•

Is the room temperature below your selected temperature?

•

Is there direct light? (Please pull down the curtain.)

•

Are too many windows or doors open?

•

Are there too many people in the room?

•

Is there something in the room producing heat?

•

Is the air conditioner plugged in?

•

Reset plug breaker by pressing reset buttons until green light is illuminated on plug.

•

Is there a power failure?

•

Is the comp / 'full water' indicator flashing?

•

Is the room temperature below the set temperature?

SPECIFICATION FOR ARP-1200 UNITS

MODEL ARP-1200M ARP-1200DM ARP-1200E ARP-1200DE

Voltage/Hz 115V / 60Hz

Cooling (BTU/hr) 12000

Heating (BTU/hr) N/A 12500 BTU’s N/A 12500 BTU’s

Power/Ampere for cooling 950 W / 8.7 A

Power/Ampere for heating N/A 930 W / 8.6 A N/A 930 W / 8.6 A

Refrigerant R22

Control manual manual electronic w/ remote electronic w/ remote

Carton weight 73 (lbs) 33 (kg)

Carton Dimension (W x H x D) 19.7 x 15.7 x 29.5 (in) 500 x 400 x 750 (mm)

Noise Level 54.1 dB(A)

NOTE: 1. Heating capacity is only for the models with the heating function, i.e. model no. ARP-1200 DM & ARP-1200 DE.

2. Measuring condition for above is: Cooling - RT 80.6 °F (27

C), RH60%

Heating - RT 68 °F (20

C), RH60%

ARP-1200M / ARP-1200DM

ARP-1200E / ARP-1200DE

FULL ONE YEAR WARRANTY

Royal Sovereign warrants each Portable Air Conditioner to be free from defects in material and workmanship. Our obligation under this warranty is limited to

the repair or replacement, free of charge, when delivered to an authorized Royal Sovereign service center, of any defective part(s) thereof, other than parts

damaged in transit. This warranty is in effect to the original purchaser, for a period of one year from the date of purchase and is not transferable. This warranty

shall apply only if the air conditioner is used on Alternating Current (AC) circuit, in accordance with the factory provided instructions which accompany it.

LIMITED FIVE YEAR WARRANTY (COMPRESSOR)

For a period of five years from the date of purchase, when this Royal Sovereign Portable Air Conditioner is operated and maintained according to the

instruction manual provided with the product, Royal Sovereign will supply a replacement compressor (part only), free of charge, if the original compressor is

determined to be defective in workmanship or material. If repair becomes necessary, please contact our customer service center. You will be responsible for all

freight, insurance, and any other transportation charges to get the unit to our factory or service center. If shipping is required, be sure to pack the unit properly

to avoid shipping damages, as we will not be responsible for such damages.

THIS WARRANTY IS VALID THROUGHOUT THE UNITED STATES AND PUERTO RICO ONLY

EXCLUSIONS

This warranty excludes and does not cover defects, malfunctions or failures of your Royal Sovereign Portable Air Conditioner, caused by repairs by

unauthorized persons or service centers, mishandling, improper installation, modification or unreasonable use including incorrect voltage, acts of god, or failure

to provide reasonable and necessary maintenance.

This warranty is in lieu of any and all expressed warranties. In no event shall Royal Sovereign be liable for consequential or incidental

damages. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion

may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

ROYAL SOVEREIGN INTERNATIONAL, INC.

Royal Centurian Inc.

2 Volvo Drive, Rockleigh, NJ 07647 USA

TEL : +1) 201-750-1020, 800-397-1025 FAX : +1) 201-750-1022

RS International Australia PTY. LTD. Royal Sovereign Canada

30 Prime Drive, Seven Hills, NSW 2147, AUSTRALIA 164 Oakdale Road, Toronto, Ontario M3N 2S5 CANADA

TEL : +61) 2-9674-2127 FAX : +61) 2-9674-2027 TEL: +1) 416-741-8400 FAX: +1) 416-741-8185

www.royalsovereign.com / [email protected]

Royal Centurian Inc.

ARP-1200M / ARP-1200DM / ARP-1200E / ARP-1200DE

MANUAL DEL PROPIETARIO

ACONDICIONADOR DE AIRE PORTÁTIL

Lea y tenga presente estas instrucciones para futuras consultas

AIRE-CONDICIONADO PORTABLE

Model ARP-1200M / ARP-1200DM / ARP-1200E / ARP-1200DE

ANTES DE USAR LA UNIDAD

• LA UNIDAD DEBE USARSE SÓLO EN POSICIÓN VERTICAL SOBRE UNA SUPERFICIE HORIZONTAL LISA Y SEPARADA POR

LOS MENOS 20”/50cm DE OTROS OBJETOS (Fig. 1 a 4).

• NO COLOQUE OBJETOS SOBRE LA UNIDAD NI RESTRINJA LA ENTRADA/SALIDA DE AIRE (FIG. 2).

• VIGILE ATENTAMENTE A LOS NIÑOS Y MASCOTAS MIENTRAS LA UNIDAD ESTÁ FUNCIONANDO.

SEGURIDAD ELÉCTRICA

• LA UNIDAD DEBE USARSE SÓLO EN INTERIORES.

• APAGUE Y DESENCHUFE LA UNIDAD CUANDO NO SE

USA.

• NO LA USE EN AMBIENTES HÚMEDOS (FIG 3).

• NO ARRASTRE LA UNIDAD TIRANDO DEL CORDÓN DE

ALIMENTACIÓN ELÉCTRICA.

• SI EL CORDÓN DE ALIMENTACIÓN ELÉCTRICA ESTÁ

DAÑADO, DEBE REEMPLAZARLO UN ELECTRICISTA

COMPETENTE PARA EVITAR RIESGOS O LESIONES.

PARA LOGRAR EL RENDIMIENTO MÁXIMO

• No exceda el tamaño recomendado de la habitación:

164 pies cúbicos/50m3

(normalmente 66 pies cuadrados/20m2 de área útil).

• Cierre puertas y ventanas.

• Mantenga ventanas y persianas cerradas durante las

horas más soleadas.

• Mantenga limpios los filtros.

• Cuando la habitación alcance las condiciones deseadas

reduzca los valores fijados de temperatura y ventilación.

FIG.3

FIG.1 FIG.2

FIG.4

ARP-1200M / ARP-1200DM

ARP-1200E / ARP-1200DE

Parte delantera

1. Panel de Control (vea en la

página 5 una ilustración

del pane

2. Salida de aire

3. Manija para transporte

4. Rueda giratoria

Parte posterior

5. Filtro de aire

6. Entrada de aire

7. Descarga de la salida

de aire

8. Depósito para el

cordón y Cordón de

alimentación con

enchufe de disyuntor

LCDI y botones de

9. Tapón para el agua /

punto de drenaje

COMPONENTES

Accesorios

10. Adaptador de acondicionador - para conectar a la manguera y a la parte

posterior del acondicionador

11. Adaptador de ventana - para insertar sobre la manguera y en el espaciador de

ventana.

12. Manguera de descarga

13. Espaciador de ventana extensible.

14. Tubo de drenaje para drenaje continuo

15. Bandeja para el agua

16. Control remoto (sólo para el modelo electrónico)

Page is loading ...

Royal Sovereign ARP-1200M User manual

Brand: Royal Sovereign

Model: ARP-1200M

Category: Mobile air conditioners

Type: User manual

This manual is also suitable for

Air Conditioner ARP-1200M

Download PDF

report

in other languages

español: Royal Sovereign ARP-1200M Manual de usuario

Royal Sovereign ARP-1200M User manual

This manual is also suitable for

Royal Sovereign ARP-1200M User manual

in other languages

Related papers

Other documents