Crosley CLCG900FW2 Installation guide

Crosley
Brand
Crosley
Model
CLCG900FW2
Category
Tumble dryers
Type
Installation guide

This manual is also suitable for

Installation Instructions
Full Size Laundry Center Gas & Electric
instrucciones para la instalaci6n
Centro de lavanderia a gas y electrica
!
\
www.frigidaire.com P/N134889400A (0804)
CONTENTS
SUBJECT PAGE
Pre-lnstallation Requirements ....................................................................................................................................... 3
Electrical Requirements ................................................................................................................................................ 3
Water Supply Requirements ............................................................................................................................................ 3
Drain Requirements ...................................................................................................................................................... 3
Exhaust System Requirements ................................................................................................................................... 4-5
Gas Supply Requirements .............................................................................................................................................. 5
Location .................................................................................................................................................................... 5
Rough-In Dimensions ................................................................................................................................................. 6
Mobile Home Installation ............................................................................................................................................. 7
Unpacking .................................................................................................................................................................. 7
Electrical Installation .................................................................................................................................................... 8
Grounding Requirements .............................................................................................................................................. 8
3 & 4-Wire Connections ........................................................................................................................................... 8-9
Installation ............................................................................................................................................................. 9-10
ReplacementParts ..................................................................................................................................................... 10
Espahol ............................................................................................................................................................... 11-20
Laundry Center Safety
Before beginning installation, carefully read these instructions. This will simplify the installation
and ensure the laundry center is installed correctly and safely. Leavethese instructions near the
laundry center after installation for future reference.
NOTE: The electrical service to the laundry center must conform with local codes and ordinances and the latest edition of the
National Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian Electrical Code, CSA C22. 1
NOTE: The gas serviceto the laundry center must conform with local codes and ordinances and the latest edition of the National
Fuel GasCode ANSI Z223. 1/NFPA54, or in Canada, the Canadian Natural Gasand Propane Installation Code, CSAB149.1.
NOTE: The laundry center isdesigned under ANSIZ21.5.1 or ANSI/UL 2158- CAN/CSA C22.2 No. 112 (latest edition) for HOME
USEonly. This laundry center is not recommended for commercial applications such as restaurants or beauty salons, etc.
Your safety and the safety of others is very important.
We have provided many important safety messagesin the Use& Care Guide, Operating Instructions, Installation Instructions and
on your appliance. Always read and obey all safety messages.
]-his isthe safety alert symbol. Thissymbol alerts you to hazards that can kill or hurt you or others. All safety messages
will be preceded by the safety alert symbol and the word "DANGER" or "WARNING". Thesewords mean:
You will be killed or seriously injured if you don't follow instructions.
You can be killed or seriously injured ff you don't foflow instructions.
All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if the
instructions are not followed.
Foryour safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent
property damage, personal injury or lossof life.
- Do not store or use gasoline or other flammable vapors and liquid in the vicinity of this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Clear the room, building or area of all occupants.
Immediately call your gas supplier from a neighbor's phone.
• Follow the gassupplier's instructions.
• if you cannot reach your gas supplier, call the fire department.
Installationand service must be preformed by a qualified installer, service agency or the gas supplier.
PRE-INSTALLATION REQUIREMENTS
Tools and Materials Required for Installation:
1. Phillips head screwdriver
2. Channel-lock adjustable pliers
3. Carpenter's level
4. Flat or straight blade screwdriver
5. Duct tape
6. Rigid or flexible metal 4 inch (10.16 cm) duct
7.Vent hood
8. Pipe thread sealer (Gas)
9.1/4 inch socket w/ratchet
10.3/8 inch socket w/ratchet
11.3/8 inch open end wrench
12.7/16 inch open end wrench
13.9/16 inch open end wrench
ELECTRICAL REQUIREMENTS
ELECTRICLaundry Center
CIRCUIT- Individual 30 amp. branch circuit fused with 30
amp. time delay fuses or circuit breakers.
Use separately fused circuits for washers and dryers, and DO
NOToperate a washer and a dryer on the same circuit.
POWER SUPPLY- 3 wire or 4-wire, 240 volt, single phase, 60
Hz, Alternating Current.
i
POWER SUPPLYCORD KIT- 3 wire - the laundry center MUST
employ a 3-conductor power supply cord NEMA 10-30 type SRDT
rated at 240 volt AC minimum, 30 amp., with 3 open end spade
lug connectors with upturned ends or closed loop connectors
and marked for use with clothes dryers. See ELECTRICAL
CONNECTIONSFORA 3-WIRE SYSTEM.
4 wire - Thelaundry center MUSTemploy a4-conductor power
supply cord NEMA 14-30 type SRDTor ST(asrequired) rated at
240 volt AC minimum, 30 amp., with 4 open end spade lug
connectors with upturned ends or closed loop connectors and
marked for use with clothes dryers. See ELECTRICAL
CONNECTIONSFORA 4-WIRE SYSTEM.
(Canada-4-wire power supply cord isinstalled on laundry center.)
WARNING- Risk of Shock. Appliance grounded to neutral
conductor through a link. Grounding through the neutral link is
prohibited for (1) New branch circuit installations (2) mobile
homes; (3) recreational vehicles; and (4) areaswhere local codes
do not permit grounding through the neutral, (1) disconnect the
link from the neutral, (2) use grounding terminal or lead to
ground appliance in accordance with localcodes and (3) connect
neutral terminal or lead to branch circuit neutral in usual manner
(if the appliance isto be connected by means of a cord kit, use
4-conductor cord for this purpose). USECOPPERCONDUCTOR
ONLY.
OUTLET RECEPTACLE- NEMA 10-30R (3-wire) receptacle or
NEMA 14- 30R (4-wire) receptacle to be located so the power
supply cord isaccessiblewhen the laundry center isin an installed
position.
NEMA 10-30R
NEMA 14-30R
i
GASLaundry Center
]
CIRCUIT-Individual 15 amp branch circuit fused with a 15
amp maximum time delay fuse or circuit breaker.
POWER SUPPLY - 3 wire, 120 volt single phase, 60 Hz,
Alternating Current.
POWER SUPPLY CORD - The gas laundry center is equipped
with a 120 volt 3-wire power cord.
OUTLET RECEPTACLE - Properly grounded 3-prong
receptacle to be located so the power supply cord is
accessible when the washer is in an installed position. NOTE:
GFI (Ground Fault Interrupter) receptacle is not required or
recommended.
NOTE: Do not under
any circumstances
remove grounding
prong from plug.
\
Grounding Prong
WATER SUPPLY REQUIREMENTS
Hot and cold water faucets MUSTbe installed within 42 inches
(106.68 cm) of your laundry center's water inlet. The faucets
MUST be 3/4 inch (1.9 cm) garden hose type so inlet hoses
can be connected. Water pressure MUSTbe between 10 and
120 pounds per square inch (maximum unbalance pressure,
hot vs.cold, 10 psi). Your water department can advise you of
your water pressure.
DRAIN REQUIREMENTS
1. Drain capable of eliminating 17 gallons per minute.
2. A standpipe diameter of 11/4inches (3.18 cm) minimum.
3. The standpipe height above the floor should be:
Minimum heicht: 24 inches (61 cm)
Maximum heicht: 96 inches (244 cm)
96 in.
(244 cm)
Max.
NOTE: For installations requiring a longer drain hose, have a
qualified technician install a longer hose, Part Number
134042901, available from an authorized parts distributor. For
drain systems in the floor, install a siphon break kit, available
from your local hardware store.
t
24 in.(61cm)
EXHAUSTSYSTEMREQUIREMENTS
Useonly4inch(10.16cm)diameter(minimum)
flexible metal duct and approved vent hood which has a
swing-out damper(s) that opens when the dryer is in
operation. When the dryer stops, the damper(s)
automatically doses to prevent drafts and the entrance
of insects and rodents. To avoid restricting the outlet,
maintain a minimum of 12 inches (38.5 cm) clearance
between the vent hood and the ground or any other
obstruction.
Thefollowing arespecific requirements for proper
and safe operation of your laundry center. Failureto follow these
instructions can create excessivedrying times and fire hazards.
Do not install a laundry center with flexible
plastic venting materials. If your present system is made up
of plastic duct or metal foil duct, replace itwith arigid or semi-
rigid metal duct. InCanada and the United States if metal (foil
type) duct is installed, it must be of a specific type identified by
the appliance manufacturer assuitablefor usewith clothes dryers
and in the United States must also comply with the Outline for
Clothes Dryer Transition Duct, UL standard 2158A. Flexible
venting materials are known to collapse, be easily crushed and
trap lint. These conditions will obstruct clothes dryer airflow and
increase the risk of fire. Ensure the present duct is free of
any lint prior to installing dryer duct.
- Risk of Fire - A clothes dryer must be
exhausted outdoors. Do not exhaust dryer into a chimney, a
wall, a ceiling, an attic, a crawl space or any concealed space of
a building A clothes dryer produces combustible lint. If the
dryer is not exhausted outdoors some fine lint will be expelled
into the laundry area. An accumulation of lint in any area of the
home can create a health and fire hazard. The dryer must be
connected to an exhaust outdoors. Regularly inspect the
outdoor exhaust opening and remove any accumulation of lint
around the outdoor exhaust opening and in the surrounding area.
Do not allow combustible materials (for
example: clothing,draperies/curtains paper) to come in contact
with the exhaust system. The dryer MUST NOT be exhausted
into a chimney, a wall, a ceiling, or any concealed space of a
building which can accumulate lint, resulting in a fire hazard.
Do not exceed the length of duct pipe or
number of elbows allowed in the" EXHAUST DUCT LENGTHS"
chart. Lint can accumulate in the system, plugging the system
and creating a fire hazard, aswell as increasing drying times.
Do not screen the exhaust ends of the vent
system, nor use any screws or rivets to assemble the exhaust
system. Lint can become caught in the screen, on the screws or
rivets, clogging the exhaust system and creating a fire hazard
aswell as increasing drying times. Usean approved vent hood
to terminate the duct outdoors, and seal all joints with duct
tape. All male duct pipe fittings MUST be installed downstream
with the flow of air.
Explosion hazard. Do not install the laundry
center where gasoline or other flammables are kept or stored.If
the laundry center isinstalled in a garage, it must be a minimum
of 18 inches (45.7 cm) above the floor. Failure to do so can
result in death, explosion, fire or burns. The exhaust system
back pressure MUSTnot exceed 0.6 inches (1.52 cm) of water
column, measured with an inclined manometer at the point the
exhaust connects to the dryer. The exhaust system should be
inspected and cleaned a minimum of every 18 months with
normal usage. The more the dryer is used, the more often you
should check the exhaust system and vent hood for proper
operation.
The maximum length of the exhaust system depends upon the
type of duct used, number of elbows and type of exhaust hood.
The maximum length for both rigid and semi-rigid duct isshown
in the chart below.
Number
of 90 °
Turns
0
1
2
3
0
1
2
3
EXHAUST DUCT LENGTHS
EXHAUST HOOD TYPE
(10.2 CM)
Louvered
(6.35 CM)
MAXIMUM LENGTH OF 4-INCH (10.2 CM)
DIAMETER RIGID METAL DUCT
56 ft. (17.07 m)
46 ft. (14.02 m)
34 ft. (10.36 m)
32ft. (9.75m)
42 ft. (12.8 m)
36 ft. (10.97 m)
28 ft. (8.53 m)
18 ft. (5.48 m)
MAXIMUM LENGTH OF 4-INCH (10.2 CM)
DIAMETER FLEXIBLE METAL DUCT
30 ft. (9.f4 m)
22 ft. (6.7 m)
16 ft. (4.88 m)
NOT RECOMMENDED
22 ft. (6.7 m)
14 ft. (4.27 m)
10 ft. (3.05 m)
The laundry center may be exhausted four (4) ways with rear
flush installation:
1. Straight back
2. Down (8 inch [20.32 cm] length of 4 inch [10.16 cm] rigid
duct and 1 elbow down)
3. Left (8 inch [20.32 cm] length of 4 inch [10.16 cm] rigid
duct, 1 elbow down and 1 elbow left)
4. Right (8 inch [20.32 cm] length of 4 inch [10.16 cm] rigid
duct, 1 elbow down and 1 elbow right)
Although vertical orientation of the exhaust systemisacceptable,
certain extenuating circumstances could affect the performance
of the dryer:
• Only the rigid metal duct
work should be used.
• Venting vertical through
a roof may expose the
exhaust system to down
drafts causing an
increase in vent
restriction.
• Running the exhaust
systemthrough an
uninsulated area may
cause condensation and
faster accumulation of
lint.
• Compression orcrimping
of the exhaust system
will cause an increase in
vent restriction.
To exhaust up, add an 11 inch (27.94 cm) length of standard 4
inch (10.16 cm) diameter duct and a 90° elbow. The unit will
be positioned about 41/2inches (11.43 cm) away from the wall
(flush to wall exhausting may be done by going below the dryer
then sideways).
An exhaust hood positioned to line up with the dryer exhaust
can be installed directly through the outside wall. Toexhaust to
the side or down, add an 8 inch (20.32 cm) length of standard 4
inch (10.16 cm) diameter duct and a 90° elbow.
GAS SUPPLY REQUIREMENTS
1.Installation MUST conform with local codes, or in the absence
of local codes, with the National FuelGasCode, ANSI Z223.1
(latest edition) or in Canada, the current AN/CGA B149.
2.The gas supply line should be of 1/2 inch (1.27 cm) pipe.
3.If codes allow, flexible metal tubing may be used to connect
your dryer to the gas supply line. The tubing MUST be
constructed of stainless steel or plastic-coated brass.
4.The gas supply line MUSThave an individual shutoff valve.
5.A 1/8 inch (0.32 cm) N. RT. plugged tapping, accessible for
test gage connection, MUST be installed immediately
upstream of the gas supply connection to the dryer.
6.The dryer and its individual shutoff valve MUST be
disconnected from the gas supply piping system during any
pressure testing of the gas supply piping system at test
pressures equal to or less than 1/2 psig (3.45 kPa).
7.Thedryer MUST be isolated from the gassupply piping system
by closing its individual manual shutoff valve during any
pressuretesting of the gassupplypiping systemat test pressures
equal to or less than 1/2 psig (3.45 kPa).
LOCATION OF YOUR LAUNDRY CENTER
DO NOT INSTALL YOUR LAUNDRY CENTER:
1. In an area exposed to dripping water or outside weather conditions.
2. In an area where it will come in contact with curtains or drapes.
3. On carpet. Floor MUSTbe solid with a maximum slope of 1 inch (2.54 cm).
4. On a pedestal. Excessivevibration can occur.
INSTALLATION IN RECESSOR CLOSET
1. A laundry center installed in a bedroom, bathroom, recessor closet, MUSTbe exhausted outdoors.
2. No other fuel burning appliance shall be installed in the same closet asthe Gas laundry center.
3. Your laundry center needs the space around it for proper ventilation.
DO NOT INSTALL YOUR LAUNDRY CENTERINA CLOSET WITH A SOLID DOOR.
4. A minimum of 120 square inches (774.2 square cm) of opening, equally divided at the top and bottom of the door, is
required. Air openings are required to be unobstructed when a door is installed. A Iouvered door with equivalent air openings
for the full length of the door is acceptable.
5. The following illustrations show minimum clearance dimensions
installation, oIN.
(oCM)_
Closet Door
--60 SQ. IN.
(387.1 SQ. CM)
5
-- 60 SQ. IN.
(387.1 SQ. CM)
and air openings for proper operation in a recessor closet
0 IN. 1IN. ', ', ',', 0 IN.
cM) (zs4cWi,, cM)
#. .
ROUGH-IN DIMENSIONS
75_ IN.
(191.14 CM.)
l&
_r
53 IN. --/r:-
(134.62 CM.)
31% I^
(8o.65 c_
]2Y21N,J._ _ 9S/81N,
(3] ,75 CM} I (23,_
VENT--/1-"_
3 :Y4IN, __._d
(9,52CM)
DRAIN OUTLET -
(REAR) --/
27 IN,
(68,58CM)
16 1AIN,
(41,27 CM)
GASSUPPLY
PIPE(REAR)
5 1AIN, _' T
_--(] 3,33 CM)
/
42_ IN.
(107.32 CM.)
40Y2IN.
(102.87 CM.)
f
36 IN.
(91.44 CM.)
29% IN.
(75.57CM.)
_J
J
1 7/8 IN,
(4,76 CM)
31/8 IN.
(7.94 CM.)
3 IN.
(7.62_M.)
MOBILE HOME INSTALLATION
1. Dryer MUST be exhausted outside (outdoors,
not beneath the mobile home) using metal
ducting that will not support combustion. Metal
ducting must be 4 inches (10.16 cm)in
diameter with no obstructions. Rigid metal duct
is preferred.
UNPACKING
1. Using the four shipping carton corner posts (two on each side), carefully
lay the laundry center on its left side and remove the foam shipping
base.
_ Excessive weight. Use two or more people to
-- move Laundry Center.
2. If dryer isexhausted through the floor and area
beneath the mobile home is enclosed, the
exhaust system MUST terminate outside the
enclosure with the termination securelyfastened
to the mobile home structure.
X
iilil
i I,q,!,!,!,!,,! i,,_@iw! _ , ,
3. Refer to page 3 for other important venting
requirements.
4. When installing a gasdryer into a mobile home,
a provision must be made for outside make up
air. This provision is to be not less than twice
the area of thedryer exhaust outlet.
5. Installation MUST conform to current
Manufactured Home Construction & Safety
Standard (which is a Federal Regulation Title
24 CFR-Part 32-80) or when such standard is
not applicable, with American National Standard
for Mobile Homes. In Canada, the CSA Z240 is
applicable.
The laundry center isdesigned
under ANSI Z21.5.1 for
HOME USE only.
FOAM
SHIPPING
PAD
,
3.
,
,
,
,
,
9.
Return laundrycenter to an upright position.
Removethe following from
the back side of the
washer:
4 bolts,
4 yellow plastic spacers,
3 metal "P" clamps.
Remove the service panel
from the front of the
washer.
Remove the 4 nuts and 6
large washers that attach
the 2 yellow shipping
braces to the drum and
the base. Lift up on the
drum and remove the
braces (a yellow ribbon
surrounds the items to be
removed).
Remove the large
styrofoam block located
under the drum. Lift up on
the drum, tilt the base of
the foam block inwards
toward the rear of the
washer until free, then pull
it out.
Remove and discard the
yellow ribbon and label
from the front of the
washer.
Replace the service panel
and screws.
Carefully move the laundry
center to within 4 feet
(1.22m) of the final location
to begin the installation.
NOTE: If the laundry
f_
center is to be _ o
transported at a later
date, the shipping
support hardware must
be reinstalled toprevent
shipping damage.
®
®
CARTON CORNER POSTS
ELECTRICAL INSTALLATION
ALL ELECTRICLaundry Centers
The following are spedfic requirements
for proper and safe electrical installation of your laundry
center. Failure to follow these instructions can create an
electrical shock and/or a fire hazard.
_This appliance MUSTbe properly grounded.
Electrical shock can result if the laundry center isnot properly
grounded. Follow the instructions in this manual for proper
grounding.
Do not use an extension cord with this
laundry center. Some extension cords are not designed to
withstand the amounts of electrical current this laundry center
utilizes and can melt, creating electrical shock and/or fire
hazard. Locate the laundry center within reach of the receptacle
for the length power cord to be purchased, allowing some slack
in the cord. Refer to the pre-installation requirements in this
manual for the proper power cord to be purchased.
_ A U.L. approved strain relief must be
installed onto power cord. If the strain relief is not attached,
the cord can be pulled out of the laundry center and can be
cut by any movement of the cord, resulting in electrical shock.
Do nott use an aluminum wired receptacle
with a copper Wired power cord and plug (or vice versa). A
chemical reaction occurs between copper and aluminum and
can cause electrical shorts. The proper wiring and
receptacle is a copper wired power cord with a copper
wired receptacle OR aluminum wired power cord with
an aluminum wired receptade.
NOTE: Laundry centers operating on a 208 volt power supply
will have longer drying times than laundry centers operating on
a 240 volt power supply.
GROUNDING REQ UIREMENTS
Non-Canadian ELECTRICLaundry Center ]
Improper connection of the equipment
grounding conductor can result in a risk of electrical shock.
Check with a licensed electrician if you are in doubt as to
whether the appliance is properly grounded.
For a grounded cord-connected laundry center:
1. The laundry center MUST be grounded. In the event of
malfunction or breakdown, grounding will reduce the risk of
electrical shock by a path of least resistance for electrical
current.
2. If your laundry center isequipped with a power supply cord
having an equipment-grounding conductor and a grounding
plug, the plug MUSTbe plugged into an appropriate, copper
wired receptacle that is properly installed and grounded in
accordance with all local codes and ordinances. If in doubt,
call a licensed electrician.
For a permanently connected laundry center:
The laundry center MUSTbe connected to a grounded metal,
permanent wiring system;or an equipment grounding con-ductor
MUSTbe run with the circuit conductors and connected to the
equipment-grounding terminal or lead on the appliance.
[
ALL 6AS Laundry Centers
}
The laundry center isequipped with a three-prong (grounding)
plug for your protection against shock hazard and should be
plugged directly into a properly grounded three-prong receptacle.
Do not cut or remove thegrounding prong from the plug.
Canadian ELECTRICLaundry Center }
_lmproper connection of the equipment
grounding conductor can result in a risk of electrical shock.
Check with a licensed electrician if you are in doubt as to
whether the appliance is properly grounded.
For a grounded cord connected laundry center:
1. The laundry center MUST be grounded. In the event of
malfunction or breakdown, grounding will reduce the risk of
electrical shock by providing a path of least resistance for
the electrical current.
2. Sinceyour laundry center is equipped with a power supply
cord having an equipment-grounding conductor and a
grounding plug, the plug MUST be plugged into an
appropriate outlet that isproperly installed and grounded
in accordance with all codes and ordinances. If in doubt,
call a licensed electrician.
[
NON-CANAD/AN ELECTR/CLaundry Center
J
ELECTRICAL CONNECTIONS FOR A 3 WIRESYSTEM
,
,
,
,
Remove the screw securing the
terminal block access cover to the rear
panel and remove cover.
Install a U.L. approved strain relief
connector in the entry hole on the back
panel.
Insert a NEMA 10-30 Type SRDT, U.L. approved power
cord through the strain relief.
Attach the power cord neutral (central wire) conductor to
the silver colored center terminal on the terminal block.
Tighten the screw securely.
GREEN GROUND SCREW
SILVER TERMINAL
NEUTRAL
GROUND
WIRE
5. Attach the remaining two power cord outer conductors to
the outer brass colored terminals on the terminal block.
Tighten both screw securely.
6. Tighten the screws securing the cord restraint against the
power cord.
7. Reinstall the terminal access cover.
[ NON-CANAD/ANELECTR/CLaundryCenter ]
ELECTRICALCONNECTIONS FORA 4-WIRE SYSTEM
1. Remove the screw securing the
terminal block accesscover to the rear
panel and remove cover.
2. Install a U.L. approved strain relief
connector in the entry hole on the
back panel.
INSTALLATION
Leve/ing the Laundry Center
Excessive noise and vibration can be prevented by properly
leveling the washer.
1. With the laundry center in it's final position, place a level
ontop of the laundry center. Adjust the leveling legs so the
laundry center is level front-to-rear and side-to-side, and
stable corner-to-corner.
3. Remove the ground wire from the green ground screw
located above the termial block.
GREEN GROUND GREEN
SCREW CONDUCTOR
GROUND
WIRE
SILVER TERMINAL
TERMINAL BLOCK
WHITE
RED /
STRAIN '
RELIEF
POWER CORD
4. Insert a NEMA 14-30 Type STor SRDT,U.L. approved power
cord through the strain relief.
5. Attach the green power cord ground wire to the cabinet
with the green ground screw.
6. Attach the white (neutral) wire from the power cord and the
ground wire from the appliance harness to the silver-colored
center terminal on the terminal block. Tighten the screw
securely.
7. Attach the red and black wires from the power cord to the
outer brass-colored terminals on the terminal block. Tighten
both screws securely.
8. Tighten the screws securing the cord restraint firmly against
the power cord.
9. Reinstall the terminal block access cover.
Pressdown on alternate corners and sides and feel for the
slightest movement. Adjust the appropriate leg so the
washer is SOLID on the floor on ALL four legs. Keep the
leveling leg extension at a minimum for best performance of
the laundry center.
Washer Connections
.
.
3.
Run some water from the hot and cold faucets to flush the
water lines and remove particles that might clog up the water
valve screens.
Check inlet hoses to ensure the rubber washers are installed
in each end.
Carefully connect the inlet hoses to the water valve (on the
left sideof the washer cabinet), tighten by hand, then tighten
another 2/3 turn with pliers.
DO NOT CROSS THREAD OR
__.=_w__ OVERTIGHTEN THESE CONNECTIONS.
4. Determine which water faucet is the HOTwater faucet and
carefully connect the bottom inlet hose to the HOT water
faucet, tighten by hand, then tighten another 2/3 turn with
pliers. Carefully connect the top inlet hose to the COLD
water faucet, tighten by hand, then tighten another 2/3 turn
with pliers.
w . a . DO NOT CROSS THREAD OR
__,,7_,_,,__ OVERTIGHTEN THESE CONNECTIONS.
Turn the water on and check for leaks at both connections.
.
.
GAS CONNECTION (Gaslaundry centers only)
Remove the shipping cap from gas pipe at the rear of the
dryer.
NOTE: DO NOT connect the laundry center to L.P. gas
service without converting the gas valve. An L.R conversion
kit must be installed by a qualified gas technician.
Connect a 1/2 inch (1.27 cm) I.D. semi-rigid or approved
pipe from the gas supply line to the 3/8 inch (0.96 cm) pipe
located on the back of the dryer. Use a 1/2 inch (1.27 cm) to
3/8 inch (0.96 cm) reducer for the connection. Apply an
approved thread sealerthat isresistant to the corrosive action
of liquefied gases on all pipe connections.
3. Opentheshutoffvalveinthegassupplyline.
4. Testallconnectionsbybrushingonasoapywatersolution.
NEVER TEST FOR GAS LEAKS WITH AN OPEN FLAME.
Drain Hose installation
1. Form a " U " shape on the end of the drain hose with the
hose pointed toward the drain. Place the formed end in a
laundry tub or a standpipe and secure with a cable tie
provided inthe enclosure package. An air gap must be around
the drain hose. WATER WILL SIPHON FROM THE
WASHER IF THE ABOVE INSTRUCTIONS ARE NOT
FOLLOWED.
Exhaust Installation
1. Remove the two (2) screws securing the dryer front access
panel to the dryer cabinet. Lift the panel until the tabs can
be disengaged from the cabinet. Remove the panel and set
aside.
Access
Panel
Screws
3. Turn on the power at a circuit breaker/fuse box.
_ Before operating the dryer, make sure the
dryer area isclear and free from combustible materials, gasoline,
and other flammable vapors. Also see that nothing (such as
boxes, clothing, etc.) obstructs the flow of combustion and
ventilation air.
4. Reinstall the dryer front access panel.
5. Runthe washer and dryer though a cycle. Check for proper
operation.
NOTE: On gas dryers, before the burner will light, it is
necessary for the gas line to be bled of air. If the burner
does not light within 45 seconds the first time the dryer is
turned on, the safety switch will shut the burner off. If
this happens, turn the timer to "OFF" and wait 5 minutes
before making another attempt to light.
6. If your laundry center does not operate, please review the
"Avoid Service Checklist" located in your Owner's Guide
before calling for service.
7. Place these instructions in a location near the laundry
center for future reference.
NOTE: A wiring diagram islocated behind the dryer front access
panel.
REPLA CEMENT PARTS
If replacement parts are needed for your laundrycenter, contact
the source where you purchased your laundry center.
_ Destroy the carton, plastic bags, and metal
band after the laundry center is unpacked. Children might use
them for play. Cartons covered with rugs, bedspreads, or plastic
sheets can become airtight chambers causing suffocation. Place
all materials in a garbage container or make materials inaccessible
to children.
_Label all wires prior to disconnection when
servicing controls. Wiring errors can cause improper and
dangerous operation. Verify proper operation after servicing.
_l__The instructions in this manual and all other
literature included with this laundry center are not meant to
cover every possiblecondition and situation that may occur.Good
safe practice and caution MUST be applied when installing,
operating and maintaining any appliance.
Connect the exhaust duct to outside duct work. Use duct
tape to seal all joints.
2. Plug the power cord into a grounded outlet.
NOTE: Check to ensure the power is off at a circuit breaker
fuse box before plugging the power cord into an outlet.
10
Maximum benefits and enjoyment are achieved when all
the Safety and Operating instructions are understood and
practiced asa routine with your laundry tasks.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
DIMENSIONS PARA LA INSTALACION
_k
53 iN. T
(134.62 CM.)
31_ I/_
(80.65 CM.)
44 iN.
111.76 CM
I
' 1 ' II
12 T/2IN,m}_ _l 9 3/8 IN,
(31,75 CM)" --------_1 (23,_C_).
VENT-_,,1-'_ ,
_N
-_" "-_:NTRADAS
DE
3 :Y4IN, ____
(9,52 CM)
SAI_IDA AL DRENA.IE
27 IN, 11
(68,58CM)
16 1/4IN,
(41,27 CM)
LINEA DE ALIMENTA-
rY-T/ON DE GAS (ATRAS)
5 1AIN,
(13,33 CM)
421/4IN.
(107.32 CM.)
40Y2IN.
(102.87 CM.)
F
<
T s
36 iN.
(91.44 CM.)
17Y2iN.
(44.45 CM.)
!
I-
47"
25 1AIN,
(64,13 CM)
29_ IN.
(75.57 CM.)
U
2 1/2IN,
(6.35 CM)
1 7/8 IN,
(4,76 CM)
__ 3-1/81N.
(7.94 CM.)
3IN.
(7.62_M.)
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Crosley CLCG900FW2 Installation guide

Crosley
Brand
Crosley
Model
CLCG900FW2
Category
Tumble dryers
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents